Symptom Chart - Instrument Panel Cluster (IPC)

SYMPTOM CHART - INSTRUMENT PANEL CLUSTER (IPC)

Condition	Possible Sources	Action
No communication with the Instrument Panel Cluster (IPC)	Fuse Wiring, terminals or connectors IPC	REFER to MODULE COMMUNICATIONS NETWORK .
The Instrument Panel Cluster (IPC) is inoperative	Fuse Wiring, terminals or connectors Communication concern IPC	GO to PINPOINT TEST A .
Incorrect fuel gauge indication - single sender L-shaped fuel tank	Wiring, terminals or connectors Fuel pump module Fuel level sender (float and card) Fuel tank IPC	GO to PINPOINT TEST B .
Incorrect fuel gauge indication - dual sender saddle-type fuel tank	Wiring, terminals or connectors Fuel tank transfer tube Fuel pump module Fuel level sensor Fuel level sender (float and card) Fuel tank IPC	GO to PINPOINT TEST C .
The temperature gauge is inoperative	PCM IPC	GO to PINPOINT TEST D .
Incorrect temperature gauge indication	PCM concern IPC	GO to PINPOINT TEST E .
The tachometer is inoperative	PCM IPC	GO to PINPOINT TEST F .
Incorrect tachometer indication	PCM concern IPC	GO to PINPOINT TEST G .
The speedometer is inoperative	PCM IPC	GO to PINPOINT TEST H .
Incorrect speedometer indication	Tire size configuration Axle ratio configuration PCM concern IPC	GO to PINPOINT TEST I .
The odometer is inoperative	PCM IPC	GO to PINPOINT TEST J .
The All-Wheel Drive (AWD) gauge is inoperative	IPC configuration AWD concern IPC	GO to PINPOINT TEST K .
The brake warning indicator is never on	Wiring, terminals or connectors Parking brake warning indicator switch Brake fluid level switch Body Control Module (BCM) IPC	GO to PINPOINT TEST L .
The brake warning indicator is always on	Wiring, terminals or connectors Parking brake warning indicator switch Brake fluid level switch ABS concern BCM IPC	GO to PINPOINT TEST M .
The ABS warning indicator is never/always on	ABS module IPC	GO to PINPOINT TEST N .
The stability/traction control indicator is never/always on	Stability/traction control concern ABS module IPC	GO to PINPOINT TEST O .
The stability/traction control disabled indicator is never/always on	A MyKey® programmed key is in use Stability/traction control cannot be disabled ABS module IPC	GO to PINPOINT TEST P .
The LH/RH turn signal, high beam or fog lamp (MKX only) indicator is never/always on	Turn signal concern High beam concern Fog lamp concern BCM IPC	GO to PINPOINT TEST Q .
The Tire Pressure Monitoring System (TPMS) warning indicator is never/always on	Tire pressure TPMS concern BCM IPC	GO to PINPOINT TEST R .
The air bag warning indicator is never/always on	Supplemental Restraint System (SRS) concern Restraints Control Module (RCM) IPC	GO to PINPOINT TEST S .
The safety belt warning indicator is never/always on	Safety belt buckle concern RCM IPC	GO to PINPOINT TEST T .
The Malfunction Indicator Lamp (MIL) is never/always on	PCM IPC	GO to PINPOINT TEST U .
The PRNDL indicator is never on/always displays P	Wiring, terminals or connectors Brake shift interlock PCM concern Transmission Control Module (TCM) concern IPC	GO to PINPOINT TEST V .
The select shift indicator is does not display the selected range	Transmission Control Module (TCM) concern IPC	GO to PINPOINT TEST V .
The powertrain malfunction (wrench) message center warning indicator is never/always on	Electronic Throttle Control (ETC) concern AWD concern (if equipped) Transaxle concern IPC	GO to PINPOINT TEST W .
The charging system message center warning indicator is never/always on	Charging system concern PCM IPC	GO to PINPOINT TEST X .
The cruise control message center indicator is never/always on	Cruise control system concern PCM IPC	GO to PINPOINT TEST Y .
The low oil pressure message center warning indicator is never/always on	Wiring, terminals or connectors Tachometer concern Engine oil pressure switch Base engine concern PCM IPC	GO to PINPOINT TEST Z .
The engine overtemperature message center warning indicator is never/always on	PCM concern IPC	OPEN then CLOSE the driver door and VERIFY the door ajar message center warning indicator functions correctly. If the door ajar message center warning indicator does not function correctly, INSTALL a new IPC . REFER to INSTRUMENT PANEL CLUSTER (IPC) . TEST the system for normal operation. If the door ajar message center warning indicator functions correctly, GO to PINPOINT TEST D to diagnose the temperature gauge.
The grade assist message center indicator is never/always on	Grade assist system concern Transaxle concern PCM IPC	GO to PINPOINT TEST AA .
The low fuel message center indicator is never/always on	Fuel gauge indication concern IPC	GO to PINPOINT TEST AB .
The low washer fluid message center indicator is never/always on	Wiring, terminals or connectors Washer fluid level switch IPC	GO to PINPOINT TEST AC .
The door ajar message center warning indicator is never/always on	Interior lighting concern BCM IPC	GO to PINPOINT TEST AD .