Differential Bearings: Installation

WARNING: This page is about a different car, the 2007 Ford Ranger. However, it is still accessible from the selected car via links, so may be relevant.

CAUTION: Always install new gaskets and seals when assembling the axle. When building the subassembly, lubricate each component with clean rear axle lubricant. Also, lubricate the subassembly when installing it into the differential housing. Tighten all fasteners to specification.

Lubricate the new differential drive pinion bearing cups.

Fig 1: Identifying Special Tool For Differential Drive Pinion Bearing Cups

Courtesy of FORD MOTOR CO.

Using the special tools, install the differential drive pinion bearing cups.

Fig 2: Assembling Differential Housing Parts

Courtesy of FORD MOTOR CO.

NOTE: Apply a light film of oil to the differential pinion bearings before installing them.

Assemble and position the following in the differential housing.
1. Position the Screw.
2. Position the Aligning Adapter.
3. Position the inner differential pinion bearing.
4. Position the Gauge Disc.
5. Position the Gauge Block.
6. Position the outer differential pinion bearing.
Thread on the Handle.

Fig 3: Tightening Handle Using Torque Wrench

Courtesy of FORD MOTOR CO.

Using a N.m (lb-in) torque wrench, tighten the Handle.

Fig 4: Rotating Gauge Block Several Half Turns To Ensure Differential Pinion Bearings Seat Correctly

Courtesy of FORD MOTOR CO.

NOTE: Offset the Gauge Block to obtain an accurate reading.

Rotate the Gauge Block several half turns to ensure the differential pinion bearings seat correctly, and position the Gauge Block as shown.

Fig 5: Installing Special Tool And Paper Shipping Tags

Courtesy of FORD MOTOR CO.

Install the special tool and the paper shipping tags.
1. Position the special tool and the paper shipping tags.
2. Install the differential bearing caps.
3. Install the bolts.
- Tighten to 61 Nm (45 lb-ft).

Fig 6: Locating Gauge Block & Gauge Tube

Courtesy of FORD MOTOR CO.

NOTE: Use a feeler gauge, or flat, clean drive pinion position shims as a measuring device.

NOTE: Selection of a shim that is too thick results in deep tooth contact at final assembly. Do not attempt to force the gauge or shim between the Gauge Block and the Gauge Tube. A slight drag indicates a correct selection.

Using a feeler gauge, or a flat, clean drive pinion position shim, measure between the Gauge Block and the Gauge Tube. Record the measurement.
- Remove the special tools after determining the correct shim thickness.

Fig 7: Identifying Drive Pinion Position Shim

Courtesy of FORD MOTOR CO.

Select the correct thickness drive pinion position shim.
- New drive pinion position shims are available in 0.762 mm (0.030 in), 0.8128 mm (0.032 in), 0.8636 mm (0.034 in), 0.9144 mm (0.036 in), 0.9652 mm (0.038 in), 1.016 mm (0.040 in), 1.0668 mm (0.042 in), 1.1176 mm (0.044 in), 1.1684 mm (0.046 in), 1.2192 mm (0.048 in),1.27 mm (0.050 in) and 1.3208 mm (0.052 in) thickness.
- Notice the plus (+), minus (-) or zero (0) etching on the drive pinion, and adjust the thickness of the new shim. If the etching is positive, subtract the number from the selected position shim. If the etching is negative, add the number to the selected position shim.
- The selected shim thickness should be very close to the recorded thickness of the original position shim.

Fig 8: Installing Pinion Position Shim & Differential Pinion Bearing

Courtesy of FORD MOTOR CO.

Install the pinion position shim and the differential pinion bearing.
- Using the special tool and a suitable press, seat the differential pinion bearing firmly against the pinion position shim.

Fig 9: Identifying Collapsible Spacer

Courtesy of FORD MOTOR CO.

Install a new collapsible spacer.

Fig 10: Identifying Outer Drive Pinion Bearing And Drive Pinion Shaft Oil Slinger

Courtesy of FORD MOTOR CO.

Install the differential pinion bearing and the front axle drive pinion shaft oil slinger.

Fig 11: Installing Pinion Seal Using Special Tool (205-133)

Courtesy of FORD MOTOR CO.

CAUTION: Installing the pinion seal without the correct tool can result in early seal failure.

CAUTION: If the pinion seal becomes cocked during installation, remove it and install a new one.

NOTE: Pinion seal must be fully seated all the way around or pinion seal damage will occur.

Using the special tool, install the pinion seal.
Lightly lubricate the pinion gear splines.

Fig 12: Positioning Pinion Gear In Differential Housing

Courtesy of FORD MOTOR CO.

Position the pinion gear in the axle housing.

Fig 13: Locating Index Marks

Courtesy of FORD MOTOR CO.

CAUTION: Never use a metal hammer on the pinion flange or install the flange with power tools. If necessary, use a plastic hammer to tap on a tight fitting flange.

Align the index marks and install the pinion flange.

Fig 14: Locating Pinion Nut

Courtesy of FORD MOTOR CO.

Install the new pinion nut hand-tight.

Fig 15: Using Special Tool (205-126) To Hold Pinion Flange While Tightening Pinion Nut

Courtesy of FORD MOTOR CO.

CAUTION: Do not loosen the nut to reduce preload. Install a new collapsible spacer and nut if preload reduction is necessary.

NOTE: Remove the special tool before taking the differential pinion bearing preload reading.

Use the special tool to hold the pinion flange while tightening the pinion nut to set the preload.
- Rotate the pinion occasionally to make sure the differential pinion bearings are seating correctly. Take frequent differential pinion bearing preload readings by rotating the pinion with a N.m (lb-in) torque wrench. The final rotational reading must be 1.7-3.4 Nm (15-30 lb-in).

Fig 16: Installing Special Tool (205-247)

Courtesy of FORD MOTOR CO.

Install the special tool.

Fig 17: Installing Differential Case In Differential Housing

Courtesy of FORD MOTOR CO.

Install the differential case in the differential housing.

Fig 18: Measuring Total End Play

Courtesy of FORD MOTOR CO.

NOTE: Repeat this step until obtaining a consistent reading.

Measure the total end play.
1. Install the special tool.
2. Force the differential case as far as possible away from the indicator. Position the indicator tip on the machined surface and adjust it to measure full travel. With force still applied, set the indicator to zero.
3. Force the differential case as far as possible in the opposite direction.
4. Record the total end play reading on the Differential Bearing Shim Selection Procedure Worksheet, Line A in this procedure.

Fig 19: Identifying Special Tool And Differential Assembly

Courtesy of FORD MOTOR CO.

Remove the special tool, and remove the differential case.
1. Remove the special tool.
2. Remove the differential case.

Fig 20: Using Suitable Press To Install Differential Ring Gear

Courtesy of FORD MOTOR CO.

CAUTION: Do not reuse the original bolts.

Using a suitable press, install the differential ring gear.
1. Position the differential ring gear and the differential case. Start 2 or 3 new bolts to align the holes in the ring gear and the differential case.
2. Using a suitable press, install the differential ring gear.

Fig 21: Locating Differential Ring Gear Bolts

Courtesy of FORD MOTOR CO.

Install the remaining new differential ring gear bolts.
- Tighten to 122 Nm (90 lb-ft).

Fig 22: Locating Special Tool And Differential Assembly In Differential Housing

Courtesy of FORD MOTOR CO.

Install the special tool and position the assembly in the differential housing.
1. Install the special tool.
2. Position the assembly in the differential housing.

Fig 23: Positioning Special Tool

Courtesy of FORD MOTOR CO.

Position the special tool.

Fig 24: Forcing Differential Ring Gear Into Mesh With Pinion Gear (Zero Backlash)

Courtesy of FORD MOTOR CO.

Force the differential ring gear into mesh with the pinion gear (zero backlash). With force still applied, set the special tool to zero.

Fig 25: Forcing Differential Ring Gear Away From Pinion Gear As Far As Possible

Courtesy of FORD MOTOR CO.

Force the differential ring gear away from the pinion gear as far as possible. Record the reading on the Differential Bearing Shim Selection Procedure Worksheet, Line D in this procedure.

Fig 26: Positioning Special Tool

Courtesy of FORD MOTOR CO.

Remove the special tool.

Fig 27: Removing Differential Case From Differential Housing

Courtesy of FORD MOTOR CO.

Remove the differential case from the differential housing. Remove the special tool from the differential case hubs.

Complete the worksheet, and select the appropriate thickness differential shims. New differential shims are available in 0.0762 mm (0.003 in), 0.127 mm (0.005 in), 0.25 mm (0.010 in) and 0.762 mm (0.030 in) thickness.

DIFFERENTIAL BEARING SHIM SELECTION PROCEDURE WORKSHEET

Line	Item	Result (actual)	Result (example)
A	Total end play reading (without gears)		2.032 mm (0.080 in)
B	Add preload	+0.2032 mm (+0.008 in)	+0.2032 mm (+0.008 in)
C	Total (add A and B)		2.2352 mm (0.088 in)
D	End play measurement (with gears)		1.0414 mm (0.041 in)
E	Subtract the shim thickness on the ring gear side	-0.0762 mm (-0.003 in)	-0.0762 mm (-0.003 in)
F	Total (subtract E from D) (thickness of shims to place on the ring gear side)		0.9652 mm (0.038 in)
G	Total (subtract F from C) (thickness of shims to place on the drive pinion side)		1.27 mm (0.050 in)

Fig 28: Installing Differential Bearing Shims And Differential Bearing

Courtesy of FORD MOTOR CO.

Install the differential shims and the differential bearing.
1. Position the differential shims and the differential bearing.
2. Using a suitable press, install the differential bearing.
- Repeat this step for opposite side of the differential case.

Fig 29: Positioning Clutch Housing Gauge Needle In Differential Carrier Spreader Adapter Hole

Courtesy of FORD MOTOR CO.

Install the special tools.
- Position the Clutch Housing Alignment Adapter needle in the Housing Spreader Adapter hole.

Fig 30: Spreading Differential Housing To Specification

Courtesy of FORD MOTOR CO.

CAUTION: Over spreading can damage the differential housing.

Spread the differential housing to the specification.

Fig 31: Identifying Special Tools (100-002) & (308-021)

Courtesy of FORD MOTOR CO.

Remove the special tools.

Fig 32: Installing Differential Bearing Cups & Differential Case In Differential Housing

Courtesy of FORD MOTOR CO.

NOTE: Push the differential case downward to fully seat the differential bearing cups in the differential housing.

Install the differential bearing cups and the differential case in the differential housing.
1. Position the differential bearing cups on the differential bearings.
2. Lower the differential case in place.

Fig 33: Locating Differential Bearing Cap And Bolts

Courtesy of FORD MOTOR CO.

CAUTION: Do not tighten the bolts to specification at this time.

Install the differential bearing caps in their original positions.
1. Position the differential bearing caps.
2. Install the bolts hand-tight.
Remove the special tools.

Fig 34: Locating Differential Bearing Cap Bolts

Courtesy of FORD MOTOR CO.

Tighten the bolts.
- Tighten to 61 Nm (45 lb-ft).
Verify that the differential case rotates freely.

Fig 35: Measuring Differential Ring Gear Backlash

Courtesy of FORD MOTOR CO.

Using the special tools, measure the backlash at 3 equally spaced points on the differential ring gear.
1. Mount the special tool.
2. Position the special tool.
3. Zero the indicator.
4. Turn the differential ring gear without turning the pinion gear. Record the measurement.
- The backlash tolerance is 0.13 mm (0.005 in) to 0.20 mm (0.008 in) and cannot vary more than 0.05 mm (0.002 in) between points checked.
- If the backlash is not within specification, correct by increasing the thickness of one differential bearing shim and decreasing the thickness of the other differential bearing shim by the same amount.

Fig 36: Measuring Differential Ring Gear Backlash Using Special Tools

Courtesy of FORD MOTOR CO.

Remove the special tools.
Apply marking compound and rotate the differential assembly 5 complete revolutions.
Verify an acceptable pattern check. For additional information, refer to DIAGNOSTIC TESTS .
Install the RH axle shaft.

Fig 37: Applying Continuous Bead Of Sealant To Differential Housing Cover Mounting Surface

Courtesy of FORD MOTOR CO.

CAUTION: The machined surfaces on the differential housing and the differential housing cover must be clean and free of oil before applying the new silicone sealant. Cover the inside of the axle before cleaning the machined surface to prevent contamination.

CAUTION: Install the differential housing cover within 15 minutes of applying the silicone material.

CAUTION: Allow the sealant to cure for one hour before filling the axle with lubricant.

Apply a continuous bead of sealant, of the specified thickness, to the differential housing cover mounting surface.
Install the differential housing cover and the differential housing cover bolts.
- Tighten to 29 Nm (21 lb-ft).
Install the axle assembly. For additional information, refer to Axle Assembly .
Fill the axle with 1.54 liters (3.25 pints) of lubricant.