A/C Odor Treatment

WARNING: This page is about a different car, the 2006 Mercury Montego, 2006 Ford Freestyle, and 2006 Ford Five Hundred. However, it is still accessible from the selected car via links, so may be relevant.

WARNING:

Avoid contact with eyes and skin. Contact with eyes and skin will cause irritation. Wear chemical goggles when using the A/C cooling coil coating.
This procedure should only be carried out in well ventilated areas. Open all windows and doors of the vehicle. Leave doors and windows open during the entire procedure. Avoid breathing vapors.
Read all instructions and warnings packaged with the A/C cooling coil coating. For additional information, see the material safety data sheet (MSDS) for this product.

NOTE: There are typically 4 types of objectionable odors found in a vehicle:

Chemical odors
Environmental odors
Human and other interior-generated odors
Microbiological odors

Before determining that A/C order treatment is required, the source and the circumstances under which the odor occurs must be determined.

NOTE:

Chemical odors are usually constant regardless of the climate control system setting although they may be enhanced by A/C operation. Most chemical odors are caused by fluid leaks or incorrectly cured adhesives. Chemical odors can be eliminated by repairing the leaking component and removing any residue.
Environmental odors usually occur for a short time and diminish after the vehicle passes through the affected area. These odors are typically only detected when the vehicle windows are open, or when the climate control system is operating in a mode that allows for fresh air. Environmental odors cannot be eliminated because they are external in source, but they may be minimized by switching to a climate control setting that uses recirculated air.
Human and other interior-generated odors occur while the source is present and may linger for a short time after. These odors may be more noticeable during A/C operation. Human odors may be eliminated by removing the source and cleaning the affected area.
Microbiological odors, if in the A/C system, usually last for about 30 seconds after the system is turned on. They will be detected while the A/C is turned on and using either outside or recirculated air. Microbiological odors that occur in areas other than the A/C system (for example, water in doors or wet carpeting) may last indefinitely and will be more intense when recirculated air is used. Microbiological odors will not be present at temperatures at or below 10°C (50°F).

Microbiological odors can be eliminated by removing the source and treating the affected area. Standing water must be allowed to drain and dry out. A/C systems may be treated by using A/C cooling coil coating as described in the service procedure below.

Microbiological odors result from microbial growth supported by warm temperatures and moisture. Microbiological odors are described as musty/mildew type smells and may occur on/in:

foam seals.
rubber seals.
adhesives.
standing water.

water soaked carpet/trim.

Identify the type of odor present in the vehicle. Do not proceed with A/C odor treatment if the odor source is found to be outside of the A/C system. Refer to ODOR DESCRIPTION TABLE for examples.

ODOR DESCRIPTION TABLE

Odor Source	Odor Description
Chemical Odors
Coolant	Sweet smell
Fuel	Gasoline or diesel fuel smell
Oil	Oil type or burning smell
Power Steering Fluid	Oil type or burning smell
Transmission Fluid	Oil type or burning smell
Washer Fluid	Alcohol type smell
Gear Lube	Garlic/sulfur smell
Refrigerant Oil	Ether type smell
Carpet/trim Adhesives	Fishy, urine or sweet smell
Evaporator Core Coating	Wet cement type smell
Environmental Odors
Exhaust	Exhaust, fuel or burning type smell
Industrial Pollutants	Various smells
Dust	Musty, mildew or wet cement type smell
Pollen	Sweet smell
Tobacco	Burning, tar smell
Human and Other Interior Generated Odors
Body Secretions	Body odor
Perfuming Agents	Sweet or fragrance smell
Clothing	Musty, mildew or body odors
Food/Beverage	Sweet, musty, mildew or fishy smell
Microbiological Odors
Microbiological Odors Occurring Inside of A/C System	Musty, mildew smell lasting about 30 seconds after A/C is turned on
Microbiological Odors Occurring Outside of A/C System	Musty, mildew smell lasting indefinitely and possibly more pronounced when using recirculated air

Identify the source of the odor.
- Check the passenger and driver side carpet for moisture. Continue diagnosis if moisture is found.
- Check the blower motor and blower motor cover (if equipped) for moisture resulting from water bypassing the cowl baffling system. Continue diagnosis if moisture is present.
- Check the evaporator core drain tube for restriction.
- Check the cowl top panel and air inlet screen for standing water or foreign material. If possible, remove any standing water and clean the air inlet screen using a wet/dry vacuum.
Open all vehicle windows.
Disconnect the low-side A/C pressure switch (cycling or low-charge protection) electrical connector.
Remove the evaporator air discharge temperature sensor (if equipped).
Set the following.
- Enable the A/C using fresh air inlet.
- Adjust the temperature setting to full warm.
- Adjust the blower motor speed to HI.
Run the engine for 25 minutes to dry out the A/C system.
Turn the ignition OFF.
Remove the blower motor.

NOTE: Blower motor speed controls that are mounted outside of the evaporator core housing and not exposed to the blower motor airflow do not need to be removed.

Remove the blower motor resistor (if equipped) or blower motor speed control (if equipped and exposed to the inside of the evaporator core housing).

CAUTION: To avoid damage to the vehicle interior, do not spill or spray this product on any interior surface.

Add one full bottle of A/C cooling coil coating to the applicator or sprayer.
Insert the nozzle into the evaporator housing and direct the spray toward the evaporator core face. Spray the entire evaporator core face until empty.
Install the blower motor and blower motor resistor (if equipped) or blower motor speed control (if equipped).
Install the evaporator air discharge temperature sensor (if equipped),
Repeat Steps 6 through 8 to cure the evaporator core coating.
Connect the low-side A/C pressure switch (cycling or low-charge protection) electrical connector.