Occupant Classification System Module (OCSM) DTC Chart

WARNING: This page is about a different car, the 2010 Lincoln MKX and 2010 Ford Edge. However, it is still accessible from the selected car via links, so may be relevant.

OCCUPANT CLASSIFICATION SYSTEM MODULE (OCSM) DTC CHART

DTC ⁽¹⁾

Description

Action To Take

B00A0:54

Occupant Classification System: Missing Calibration

GO to PINPOINT TEST AC .

B00A0:67

Occupant Classification System: Signal Incorrect After Event

CARRY OUT the Occupant Classification Sensor (OCS) System Zero Seat Weight Test. REFER to OCCUPANT CLASSIFICATION SENSOR (OCS) SYSTEM ZERO SEAT WEIGHT TEST .

B00A0:76

Occupant Classification System: Wrong Mounting Position

GO to PINPOINT TEST AC .

B00A0:97

Occupant Classification System: Component or System Operation Obstructed or Blocked

GO to PINPOINT TEST X .

B00C0:12

Passenger Seat Occupant Classification Sensor "A": Circuit Short To Battery

GO to PINPOINT TEST Y .

B00C0:13

Passenger Seat Occupant Classification Sensor "A": Circuit Open

GO to PINPOINT TEST Y .

B00C0:1A

Passenger Seat Occupant Classification Sensor "A": Circuit Resistance Below Threshold

GO to PINPOINT TEST Y .

B00C0:49

Passenger Seat Occupant Classification Sensor "A": Internal Electronic Failure

GO to PINPOINT TEST AC .

B00C0:81

Passenger Seat Occupant Classification Sensor "A": Invalid Serial Data

CARRY OUT the Occupant Classification Sensor (OCS) System Reset. REFER to OCCUPANT CLASSIFICATION SENSOR (OCS) SYSTEM RESET .

B00C1:12

Passenger Seat Occupant Classification Sensor "B": Circuit Short To Battery

GO to PINPOINT TEST Z .

B00C1:13

Passenger Seat Occupant Classification Sensor "B": Circuit Open

GO to PINPOINT TEST Z .

B00C1:1A

Passenger Seat Occupant Classification Sensor "B": Circuit Resistance Blow Threshold

GO to PINPOINT TEST Z .

B00C1:49

Passenger Seat Occupant Classification Sensor "B": Internal Electronic Failure

GO to PINPOINT TEST AC .

B00C1:81

Passenger Seat Occupant Classification Sensor "B": Invalid Serial Data

CARRY OUT the Occupant Classification Sensor (OCS) System Reset. REFER to OCCUPANT CLASSIFICATION SENSOR (OCS) SYSTEM RESET .

B00C2:12

Passenger Seat Occupant Classification Sensor "C": Circuit Short To Battery

GO to PINPOINT TEST AA .

B00C2:13

Passenger Seat Occupant Classification Sensor "C": Circuit Open

GO to PINPOINT TEST AA .

B00C2:1A

Passenger Seat Occupant Classification Sensor "C": Circuit Resistance Blow Threshold

GO to PINPOINT TEST AA .

B00C2:49

Passenger Seat Occupant Classification Sensor "C": Internal Electronic Failure

GO to PINPOINT TEST AC .

B00C2:81

Passenger Seat Occupant Classification Sensor "C": Invalid Serial Data

CARRY OUT the Occupant Classification Sensor (OCS) System Reset. REFER to OCCUPANT CLASSIFICATION SENSOR (OCS) SYSTEM RESET .

B00C3:12

Passenger Seat Occupant Classification Sensor "D": Circuit Short To Battery

GO to PINPOINT TEST AB .

B00C3:13

Passenger Seat Occupant Classification Sensor "D": Circuit Open

GO to PINPOINT TEST AB .

B00C3:1A

Passenger Seat Occupant Classification Sensor "D": Circuit Resistance Blow Threshold

GO to PINPOINT TEST AB .

B00C3:49

Passenger Seat Occupant Classification Sensor "D": Internal Electronic Failure

GO to PINPOINT TEST AC .

B00C3:81

Passenger Seat Occupant Classification Sensor "D": Invalid Serial Data

CARRY OUT the Occupant Classification Sensor (OCS) System Reset. REFER to OCCUPANT CLASSIFICATION SENSOR (OCS) SYSTEM RESET .

B1193:00

Crash Event Storage Full and Locked: No Sub Type Information

INSTALL new passenger seat track assembly with OCS weight sensor bolts. REFER to REMOVAL AND INSTALLATION and INSPECTION AND REPAIR AFTER A SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPLOYMENT .

B1A59:01

Sensor 5 Volt Supply: General Electrical Failure

GO to PINPOINT TEST AD .

B1A59:11

Sensor 5 Volt Supply: Circuit Short to Ground

GO to PINPOINT TEST AD .

U0100:00

Lost Communication With ECM/PCM "A": No Sub Type Information

U0100:00 will set in a module that is reporting a communication fault from another module on the data bus. The module that reports the fault is not the problem module. Do not install a new OCSM as part of repair for DTC U0100:00.
REFER to MODULE COMMUNICATIONS NETWORK to diagnose the High Speed Controller Area Network (HS-CAN)/module communication concern.

U0151:00

Lost Communication With Restraints Control Module: No Sub Type Information

U0151:00 will set in a module that is reporting a communication fault from another module on the data bus. The module that reports the fault is not the problem module. Do not install a new Occupant Classification System Module (OCSM) as part of repair for DTC U0151:00.
REFER to MODULE COMMUNICATIONS NETWORK to diagnose the HS-CAN /module communication concern.

U0401:00

Invalid Data Received From ECM/PCM "A": No Sub Type Information

U0401:00 will set in a module that is reporting a communication fault from another module on the data bus. The module that reports the fault is not the problem module. Do not install a new OCSM as part of repair for DTC U0401:00.
REFER to MODULE COMMUNICATIONS NETWORK to diagnose the HS-CAN /module communication concern.

U200D:12

Control Module Output Power A: Circuit Short To Battery

GO to PINPOINT TEST AE .

U3003:16

Battery Voltage: Circuit Voltage Below Threshold

GO to PINPOINT TEST W .

U3003:17

Battery Voltage: Circuit Voltage Above Threshold

GO to PINPOINT TEST W .

U3000:49

Control Module: Internal Electronic Failure

INSTALL a new OCSM . REFER to OCCUPANT CLASSIFICATION SYSTEM MODULE (OCSM) - MANUAL SEAT TRACK or OCCUPANT CLASSIFICATION SYSTEM MODULE (OCSM) - POWER SEAT TRACK .

U3000:53

Control Module: Deactivated

INSTALL a new OCSM . REFER to OCCUPANT CLASSIFICATION SYSTEM MODULE (OCSM) - MANUAL SEAT TRACK or OCCUPANT CLASSIFICATION SYSTEM MODULE (OCSM) - POWER SEAT TRACK .

U3000:54

Control Module: Missing Calibration

CARRY OUT the Occupant Classification Sensor (OCS) System Reset. REFER to OCCUPANT CLASSIFICATION SENSOR (OCS) SYSTEM RESET .

⁽¹⁾	DTC: Retrieved using scan tool.