LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2009 >> Flex Limited, FWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 1602 (Seat System - Seating) >> Disassembly And Assembly >> Seat Cushion - Driver >> Disassembly

Seat Cushion - Driver: Disassembly

WARNING: This page is about a different car, the 2009 Mercury Sable, 2009 Ford Taurus X, and 2009 Ford Taurus. However, it is still accessible from the selected car via links, so may be relevant.
Fig 1: Driver Front Seat Cushion With Torque Specifications
GF0045430Courtesy of FORD MOTOR CO.
Item Part Number Description
1 62900 Cushion trim cover
2 - Cushion heater mat electrical connector
3 - Cushion foam pad
4 N803766 Cushion frame-to-seat track nuts (4 required)
5 60392 Cushion frame-to-backrest frame bolts (2 required)
6 63100 Cushion frame
7 611B24 Small roll pins (2 required)
8 620A24 Large roll pins (2 required)
9 62184 Side shield
10 14D716 Power recliner knob (if equipped)
11 620A90 Manual recliner handle (if equipped)
12 14711 Seat control switch knob
13 14A701 Seat control switch
14 - Seat control switch electrical connector (part of 14A698)
15 - Side air bag module electrical connector (part of 14A698) (if equipped)
16 - Driver seat module (if equipped)
17 619A74 Manual recliner (if equipped)
18 - Heater mat electrical connector (part of 14A698)
19 - Rivets (2 required)
20 - Driver seat module electrical connector (if equipped)
21 619A74 Power recliner (if equipped)
22 - Power recliner mounting screws (3 required) (if equipped)
23 - Fore/aft power seat motor electrical connector (part of 14A698)
24 - Power recliner motor electrical connector (part of 14A698) (if equipped)
25 W520114 Safety belt buckle pretensioner nut
26 611B09 Safety belt buckle pretensioner
27 - Safety belt buckle pretensioner electrical connector (part of 611B09)
28 - Seat position sensor electrical connector (part of 14A698)
29 - Front height power seat motor electrical connector (part of 14A698)
30 61700 Seat track
31 - Rear height power seat motor electrical connector (part of 14A698)
WARNING: Never probe the electrical connectors on safety belt buckle/retractor pretensioners or adaptive load limiting retractors. Failure to follow this instruction may result in the accidental deployment of the safety belt pretensioners or adaptive load limiting retractors, which increases the risk of serious personal injury or death.
WARNING: Never probe the electrical connectors on air bag, safety canopy or side air curtain modules. Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.
NOTE: The air bag warning indicator illuminates when the correct restraint control module (RCM) fuse is removed and the ignition switch is ON.
NOTE: The supplemental restraint system (SRS) must be fully operational and free of faults before releasing the vehicle to the customer.

All seats 

  1. Remove the front seat. For additional information, refer to Seat - Front .
  2. Remove the front seat backrest. For additional information, refer to Seat Backrest - Front .
  3. Remove the seat track. For additional information, refer to Seat Track - Front .

    4. Seat with power recline 

  4. Disconnect the power recliner motor electrical connector.
  5. Drive out the 2 large roll pins.
  6. Remove the 3 bolts and the power recliner assembly.
    • To install, tighten to 10 Nm (89 lb-in).

    7. Seat with manual recline 

  7. Drive out the 2 large roll pins and remove the manual recliner.

    8. All seats 

  8. If equipped, remove the 2 rivets, disconnect the 4 connectors and remove the driver seat module.
  9. Remove the seat wire harness.
  10. Remove the hog rings and the cushion trim cover from the cushion foam pad.
    11. Fig 2: Locating Hog Rings For Seat Cushion Trim Cover
    G03988965Courtesy of FORD MOTOR CO.
  11. To assemble, reverse the disassembly procedure.
  12. Install the seat. For additional information, refer to Seat - Front .
    • If a new seat track has been installed on a driver seat with memory, the seat must be operated in all directions through the full range of travel to avoid a premature stopping point occurrence after the vehicle is returned to the customer.
  13. Repower the SRS. For additional information, refer to Supplemental Restraint System (SRS) Depowering and Repowering in the General Procedures portion of SUPPLEMENTAL RESTRAINT SYSTEM article.
scientia non olet · About LEMON Manuals