LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2009 >> Flex Limited, FWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 1424 (Steering System - General Information) >> Diagnostic Tests >> Steering System >> Symptom Chart - NVH

Symptom Chart - NVH

WARNING: This page is about a different car, the 2009 Ford Mustang. However, it is still accessible from the selected car via links, so may be relevant.
NOTE: NVH symptoms should be identified using the diagnostic tools that are available. For a list of these tools, an explanation of their uses and a glossary of common terms, refer to NOISE, VIBRATION AND HARSHNESS article. Since it is possible any one of multiple systems may be the cause of a symptom, it may be necessary to use a process of elimination type of diagnostic approach to pinpoint the responsible system. If this is not the causal system for the symptom, refer back to NOISE, VIBRATION AND HARSHNESS article for the next likely system and continue diagnosis.
Symptom Chart - NVH

Condition Possible Sources Action
  • Steering system cold start noise
  • Blockage in the power steering fluid reservoir caused by power steering fluid contamination
    NOTE: Some noise during an extremely cold start (-12.2°C [-10°F]) is normal and should improve as the steering system warms up (usually within 60 seconds).
    NOTE: It may be necessary to remove the power steering fluid reservoir to flush contamination trapped in the reservoir screen.
  • CHECK the power steering fluid reservoir for contamination. FLUSH the power steering system as necessary. REFER to Power Steering System Flushing .
 
  • Air in the steering hydraulic system (aerated fluid)
  • Steering grunt or shudder - occurs when turning into or out of a turn at low speeds (temperature sensitive)
  • Air in the steering hydraulic system (aerated fluid)
  • CHECK for leaks in the system. REFER to Power Steering Leak Test Component Test. PURGE the air from the system. REFER to Power Steering System Purging .
 
  • Steering gear or power steering hoses
  • Steering system clonk - hydraulic knocking sound
  • Air in the steering hydraulic system (aerated fluid)
    NOTE: Some amount of clonk noise is considered acceptable. If in doubt of the acceptability, compare to another vehicle.
  • CHECK for leaks in the system. REFER to Power Steering Leak Test Component Tests . PURGE the air from the system. REFER to Power Steering System Purging .
  • Power steering pump moan - loud humming noise occurs when the steering wheel is rotated to the stop position. Produces a 120-600 Hz frequency that changes with RPM
  • Low fluid and/or air in the steering hydraulic system (aerated fluid)
  • CHECK for leaks in the system. REFER to Power Steering Leak Test Component Test. PURGE the air from the system. REFER to Power Steering System Purging . If a pump moan still exists, INSTALL a new power steering pump. REFER to POWER STEERING article.
 
  • Power steering fluid reservoir or screen is blocked or damaged
  • INSPECT the reservoir. FLUSH or INSTALL a new reservoir as necessary.
 
  • Power steering line/hose grounded to chassis
  • INSPECT the power steering lines/hoses. REPAIR as necessary.
 
  • Power steering pump brackets loose or misaligned
  • CHECK bolts, brackets and bracket alignment. TIGHTEN bolts to specification. REPAIR or INSTALL new brackets as necessary. REFER to POWER STEERING article.
 
  • Steering gear isolators
  • INSPECT the isolators for wear or damage. REPAIR as necessary.
  • Steering gear clunk - occurs only while cornering over a bump (can be temperature sensitive)
  • Steering gear
  • INSPECT the steering gear for loose mounting bolts. TIGHTEN to specification as necessary. REFER to POWER STEERING article.
  • Feedback (rattle, chuckle or knocking noise in the steering gear) - roughness is felt in the steering wheel when the vehicle is driven over rough surfaces
  • Steering column shaft/U-joints damaged or worn
 
  • Loose, damaged or worn tie-rod ends
  • INSPECT and INSTALL new tie-rod ends as necessary. Go to Steering Linkage Component Tests .
 
  • Steering gear insulators or mounting bolts loose or damaged
  • TIGHTEN the bolts to specification or INSTALL new bolts as necessary. REFER to POWER STEERING article.
 
  • Steering column shaft bolts are loose
 
  • Steering column damaged or worn
  • REPAIR or INSTALL a new steering column as necessary. REFER to STEERING COLUMN article.
  • Power steering hiss or whistle
  • Steering column shaft-to-steering gear is binding or misaligned
  • REPAIR or INSTALL a new steering column shaft as necessary. REFER to STEERING COLUMN article.
 
  • Grounded or loose steering column boot at the dash panel
  • REPAIR as necessary.
 
  • Damaged or worn steering gear input shaft and valve
  • REPAIR or INSTALL a new steering gear as necessary. REFER to POWER STEERING article.
 
  • Restricted power steering lines/hoses
  • INSTALL new power steering lines/hoses as necessary. REFER to POWER STEERING article.
  • Steering column rattle
  • Loose bolts or attaching brackets
  • TIGHTEN the bolts to specification.
 
  • Loose, worn or insufficiently lubricated column bearings
  • LUBRICATE bearings or INSTALL new steering column bearings or steering column as necessary. REFER to STEERING COLUMN article.
 
  • Steering shaft insulators damaged or worn
 
  • Steering column shaft compressed or extended
  • INSPECT the rubber spider coupling for damage. INSTALL a new steering column shaft. REFER to STEERING COLUMN article.
  • Steering gear squeak
  • Incorrect power steering fluid in system
  • If incorrect power steering fluid is suspected, FLUSH the power steering system. REFER to Power Steering System Flushing . If noise persists after system flush, INSTALL a new steering gear. REFER to POWER STEERING article.
 
  • Steering gear rotary seal
    NOTE: VERIFY that the steering gear is the source of the noise. It may be necessary to replicate the customer operating conditions (fluid temperature, turning rate of steering wheel) to get the squeak to reoccur.
  • INSTALL a new steering gear as necessary. REFER to POWER STEERING article.
 
  • Stone shield (if equipped)
  • MAKE SURE that the stone shield is correctly installed and that it is not making contact with the steering shaft. REPOSITION stone shield or INSTALL a new stone shield as necessary.
  • Steering column squeak, cracks or grinds
  • Insufficiently lubricated steering shaft bushings
  • LUBRICATE the steering shaft and shaft tube seals.
 
  • Loose or misaligned steering column shrouds
  • TIGHTEN or ALIGN the steering column shrouds.
 
  • Steering wheel rubbing against steering column shrouds
  • REPOSITION the steering column shrouds.
 
  • Upper or lower bearing sleeves out of position
  • REPOSITION the bearing sleeves.
  • Power steering pump noisy
  • Power steering pump
  • INSTALL a new power steering pump as necessary. REFER to POWER STEERING article.
  • Power steering pump relief noise
  • Power steering fluid flow into the bypass valve of the pump valve housing, with fluid temperature below 54°C (130°F)
  • Acceptable condition.
  • Power steering pump whine noise
  • Aerated fluid
 
  • Damaged power steering pump
  • INSTALL a new power steering pump as necessary. REFER to POWER STEERING article.
  • High speed shake or shimmy - occurs at high speeds
  • Worn or damaged steering linkage components
scientia non olet · About LEMON Manuals