Diagnostic Routines

WARNING: This page is about a different car, the 2008 Mercury Sable, 2008 Ford Taurus X, and 2008 Ford Taurus. However, it is still accessible from the selected car via links, so may be relevant.

ENGAGEMENT CONCERN: NO FORWARD

Possible Component		Reference/Action
201 - ELECTRICAL ROUTINE
Powertrain Control System
	No electrical concerns
301 - HYDRAULIC/MECHANICAL ROUTINE
Transmission Fluid Level
	Low transmission fluid level	Check transmission fluid level and adjust as necessary. Refer to Preliminary Inspection .
	Transmission fluid condition	Carry out transmission fluid condition check. Refer to Preliminary Inspection .
Selector Lever Linkage (Internal/External)
	Damaged or out of adjustment	Inspect for damage. Repair as required. Verify selector lever cable adjustment. Refer to AUTOMATIC TRANSAXLE/TRANSMISSION EXTERNAL CONTROLS article.
Incorrect Pressures
	Line Pressure Control (LPC) solenoid stuck low	Check pressure at line pressure tap. Carry out Line Pressure Tests and Stall Speed Tests. Refer to Special Testing Procedures . See the Line Pressure Chart for specification. If pressures are low, check the following possible components: Main control valve body Pump assembly LPC solenoid
Main Control Valve Body
	Bolts out of torque specification	Adjust bolts to specification.
	Gaskets and Separator Plate - damaged, off location	Inspect gaskets for damage. Install new as required.
	Manual Control Valve - damaged	Inspect for damage. Install new as required.
Pump Assembly
	Bolts out of torque specification	Inspect for damage. Install a new pump as required.
	Porosity/cross leaks/ball missing or leaking	Inspect for damage. Install a new pump as required.
	Components - damaged	Inspect for damage. Install a new pump as required.

ENGAGEMENT CONCERN: NO REVERSE

Possible Component		Reference/Action
202 - ELECTRICAL ROUTINE
Powertrain Control System
	No electrical concerns
302 - HYDRAULIC/MECHANICAL ROUTINE
Transmission Fluid Level
	Low transmission fluid level	Check transmission fluid level and adjust as necessary. Refer to Preliminary Inspection .
	Transmission fluid condition	Carry out transmission fluid condition check. Refer to Preliminary Inspection .
Selector Lever Linkage (Internal/External)
	Damaged or out of adjustment	Inspect for damage. Repair as required. Verify selector lever cable adjustment. Refer to AUTOMATIC TRANSAXLE/TRANSMISSION EXTERNAL CONTROLS article.
Incorrect Pressures
	Line Pressure, Line Pressure Control (LPC) Pressure - low	Carry out Line Pressure Tests and Stall Speed Tests. Refer to Special Testing Procedures . Check pressure at line pressure tap. See the Line Pressure Chart for specifications. If pressures are low, check the following possible components: Main control valve body Pump assembly Low/reverse clutch assembly Direct clutch assembly Shift Solenoid B (SSB), Shift Solenoid D (SSD) and Shift Solenoid E (SSE) solenoids
Main Control Valve Body
	Bolts out of torque specification	Tighten bolts to specification.
	Gasket and Separator Plate - damaged, off location	Inspect for damage. Install new as required.
	Manual Control Valve, Springs - stuck, damaged	Inspect for damage. Install new as required.
	Multiplex Valve, Springs - stuck, damaged	Inspect for damage. Install new as required.
	Low/Reverse Clutch Valve, Springs - stuck, damaged	Inspect for damage. Install new as required.
	Direct Clutch Valve, Springs - stuck, damaged	Inspect for damage. Install new as required.
Pump Assembly
	Bolts out of torque specification	Inspect for damage. Install a new pump as required.
	Porosity/cross leaks, pump assembly leaking, plugged hole	Inspect for damage. Install a new pump as required.
	Components damaged	Inspect for damage. Install a new pump as required.
Low/Reverse Clutch Assembly
	SSD solenoid stuck low	Inspect for damage. Install a new solenoid body as required. Refer to Solenoid Body Assembly .
	Low/Reverse regulator valve stuck	Inspect for damage. Repair as required.
	Seals, Piston, Springs - damaged	Inspect for damage. Repair as required.
	Clearance check out of specification	Inspect for damage. Carry out clearance checks.
	Friction Elements - damaged or worn	Inspect for damage. Repair as required.
Direct Clutch Assembly
	Seals, Piston, Spring - damaged	Inspect for damage. Repair or install new as required.
	SSB solenoid	Inspect for damage. Install a new solenoid body as required. Refer to Solenoid Body Assembly .
	Direct clutch regulator valve	Inspect for damage. Repair or install new as required.
	Clearance check out of specification	Inspect for damage. Carry out clearance checks.
	Friction Elements - damaged, clearance check incorrect	Inspect for damage. Repair as required.

ENGAGEMENT CONCERN: HARSH REVERSE

Possible Component		Reference/Action
203 - ELECTRICAL ROUTINE
Powertrain Control System
	Electrical Inputs/Outputs, Vehicle Wiring Harnesses, PCM, Mass Air Flow (MAF) Sensor, Intake Air Temperature (IAT) Sensor, Throttle Position (TP) Sensor, Idle Speed Control (ISC) and Power Steering Pressure (PSP) Sensor, Engine RPM, Line Pressure Control (LPC) Solenoid, Transmission Fluid Temperature (TFT), Turbine Shaft Speed (TSS) and Output Shaft Speed (OSS) sensor, Shift Solenoid B (SSB) and Shift Solenoid D (SSD) solenoids or transaxle solenoid power control circuit open/shorted	Run On-Board Diagnostic (OBD). Refer to the Introduction - Gasoline Engines article for diagnosis. Go to Pinpoint Test A , go to Pinpoint Test B , go to Pinpoint Test C and Go to Pinpoint Test E .
Solenoid Body
	Incorrect solenoid body strategy data stored in the PCM	Verify solenoid body strategy data stored in the PCM, download new identification and strategy as necessary. Refer to Solenoid Body Strategy .
303 - HYDRAULIC/MECHANICAL ROUTINE
Incorrect Pressures
	Line Pressure, LPC Pressure - high	Carry out Line Pressure and Stall Speed Tests. Refer to Special Testing Procedures . Check pressure at line pressure taps. See the Line Pressure Chart for specifications. If high, check the Main Control Valve Body.
Pump Assembly
	Bolts out of torque specification	Inspect for damage. Install a new pump as required.
	Porosity/cross leaks, pump assembly leaking, plugged hole	Inspect for damage. Install a new pump as required.
	Components damaged	Inspect for damage. Install a new pump as required.
Main Controls
	Bolts out of torque specification	Tighten bolts to specification.
	Gasket and Separator Plate - damaged, off location	Inspect for damage. Install new as required.
	Low/Reverse regulator valve - stuck, damaged	Inspect for damage. Install new as required.
	Low/Reverse boost valve - stuck, damaged	Inspect for damage. Install new as required.
	Direct regulator valve - stuck, damaged	Inspect for damage. Install new as required.
	Direct boost valve - stuck, damaged	Inspect for damage. Install new as required.
	SSB mechanically stuck - high	Install a new solenoid body. Refer to Solenoid Body Assembly .
	SSD mechanically stuck - high	Install a new solenoid body. Refer to Solenoid Body Assembly .
	Main Regulator Valve - stuck, damaged	Inspect for damage. Install new as required.
Low/Reverse Clutch Assembly
	SSD solenoid stuck low	Inspect for damage. Install a new solenoid body as required. Refer to Solenoid Body Assembly .
	Low/Reverse regulator valve stuck	Inspect for damage. Install a new solenoid body as required.
	Seals, Piston, Springs - damaged	Inspect for damage. Repair as required.
	Clearance check out of specification	Inspect for damage. Carry out clearance checks.
	Friction Elements - damaged or worn	Inspect for damage. Repair as required.
Direct Clutch Assembly
	Seals, Piston, Spring - damaged	Inspect for damage. Repair or install new as required.
	SSB solenoid stuck	Inspect for damage. Install a new solenoid body as required. Refer to Solenoid Body Assembly .
	Direct clutch regulator valve	Inspect for damage. Repair or install new as required.
	Clearance check out of specification	Inspect for damage. Carry out clearance checks.
	Friction Elements - damaged, clearance check incorrect	Inspect for damage. Repair or install new as required.

ENGAGEMENT CONCERN: HARSH FORWARD

Possible Component		Reference/Action
204 - ELECTRICAL ROUTINE
Powertrain Control System
	Electrical Inputs/Outputs, Vehicle Wiring Harnesses, PCM, Mass Air Flow (MAF) Sensor, Intake Air Temperature (IAT) Sensor, Throttle Position (TP) Sensor, Idle Speed Control (ISC) and Power Steering Pressure (PSP) Sensor, Engine RPM, Line Pressure Control (LPC) Solenoid, Transmission Fluid Temperature (TFT), Turbine Shaft Speed (TSS) and Output Shaft Speed (OSS) sensor, Shift Solenoid A (SSA) or transaxle solenoid power control circuit open/shorted	Run On-Board Diagnostic (OBD). Refer to the Introduction - Gasoline Engines article for diagnosis. Go to Pinpoint Test A , go to Pinpoint Test B , go to Pinpoint Test C and Go to Pinpoint Test E .
Solenoid Body
	Incorrect solenoid body strategy data stored in the PCM	Verify solenoid body strategy data stored in the PCM, download new identification and strategy as necessary. Refer to Solenoid Body Strategy .
304 - HYDRAULIC/MECHANICAL ROUTINE
Incorrect Pressures
	Line Pressure, LPC Pressure - high	Carry out Line Pressure and Stall Speed Tests. Refer to Special Testing Procedures . Check pressure at line pressure taps. See the Line Pressure Chart for specifications. If high, check the Main Control Valve Body, Pump Assembly.
Pump Assembly
	Bolts out of torque specification	Inspect for damage. Install a new pump as required.
	Porosity/cross leaks, pump assembly leaking, plugged hole	Inspect for damage. Install a new pump as required.
	Components damaged	Inspect for damage. Install a new pump as required.
Main Controls
	Bolts out of torque specification	Tighten bolts to specification.
	Gasket and Separator Plate - damaged, off location	Inspect for damage. Install new as required.
	Forward Clutch Seal - Leaking Between Valve Body and Case	Inspect for damage. Install new as required.
	Forward clutch regulator valve - stuck, damaged	Inspect for damage. Install new as required.
	Forward clutch boost valve - stuck, damaged	Inspect for damage. Install new as required.
	Main Regulator Valve - stuck, damaged	Inspect for damage. Install new as required.
Forward Clutch Assembly
	Seals, Piston - worn, damaged	Inspect for damage. Install new as required.
	Friction Elements - damaged	Inspect for damage. Install new as required.
	Wave Spring - damaged	Inspect for damage. Install new as required.

ENGAGEMENT CONCERN: DELAYED/SOFT REVERSE

Possible Component		Reference/Action
205 - ELECTRICAL ROUTINE
Powertrain Control System
	Electrical Inputs/Outputs, Transmission Range (TR) Sensor, Vehicle Wiring Harnesses, PCM, Line Pressure Control (LPC) Solenoid, Transmission Fluid Temperature (TFT)	Run On-Board Diagnostic (OBD). Refer to the Introduction - Gasoline Engines article for diagnosis. Go to Pinpoint Test A , go to Pinpoint Test B and Go to Pinpoint Test D .
Solenoid Body
	Incorrect solenoid body strategy data stored in the PCM	Verify solenoid body strategy data stored in the PCM, download new identification and strategy as necessary. Refer to Solenoid Body Strategy .
305 - HYDRAULIC/MECHANICAL ROUTINE
Transmission Fluid Level
	Low transmission fluid level	Check transmission fluid level and adjust as necessary. Refer to Preliminary Inspection .
	Transmission fluid condition	Carry out transmission fluid condition check. Refer to Preliminary Inspection .
Selector Lever Linkage (Internal/External)
	Damaged, out of adjustment	Inspect for damage. Repair as required. Verify selector lever cable adjustment. Refer to AUTOMATIC TRANSAXLE/TRANSMISSION EXTERNAL CONTROLS article.
Incorrect Pressures
	Line Pressure, LPC Pressure - low	Check pressure at line pressure tap. Carry out Line Pressure and Stall Speed Tests. Refer to Special Testing Procedures . If pressures are low, check the following possible components: Main Control Valve Body, Pump Assembly, Low/Reverse Clutch Assembly, Direct Clutch Assembly.
Main Controls
	Solenoid Body Filter Plugged	Inspect for damage. Install a new filter as required.
	Bolts out of torque specification	Tighten bolts to specification.
	Gaskets and Separator Plate - damaged, off location	Inspect for damage. Install new as required.
	Low/Reverse regulator valve - stuck, damaged	Inspect for damage. Install new as required.
	Low/Reverse boost valve - stuck, damaged	Inspect for damage. Install new as required.
	Direct regulator valve - stuck, damaged	Inspect for damage. Install new as required.
	Direct boost valve - stuck, damaged	Inspect for damage. Install new as required.
	Manual Control Valve, Main Regulator Valve, Converter Drain Back Valve, Springs - missing, damaged, misassembled	Inspect for damage. Repair or install new as required.
	Shift Solenoid B (SSB) stuck low	Inspect for damage. Go to Pinpoint Test A . Install a new solenoid body as required. Refer to Solenoid Body Assembly .
	Shift Solenoid D (SSD) stuck low	Inspect for damage. Install a new solenoid body as required. Refer to Solenoid Body Assembly .
Pump Assembly
	Pump Assembly - worn/cross leaks, leaking	Inspect for damage. Install new as required.
Low/Reverse Clutch Assembly
	SSD solenoid stuck low	Inspect for damage. Install a new solenoid body as required. Refer to Solenoid Body Assembly .
	Low/Reverse regulator valve stuck	Inspect for damage. Install new as required.
	Seals, Piston, Springs - damaged	Inspect for damage. Repair as required.
	Clearance check out of specification	Inspect for damage. Carry out clearance checks.
	Friction Elements - damaged or worn	Inspect for damage. Repair as required.
Direct Clutch Assembly
	Seals, Piston, Spring - damaged	Inspect for damage. Repair or install new as required.
	SSB solenoid stuck	Inspect for damage. Install a new solenoid body as required. Refer to Solenoid Body Assembly .
	Direct clutch regulator valve	Inspect for damage. Repair or install new as required.
	Clearance check out of specification	Inspect for damage. Carry out clearance checks.
	Friction Elements - damaged, clearance check incorrect	Inspect for damage. Repair as required.

ENGAGEMENT CONCERN: DELAYED/SOFT FORWARD

Possible Component		Reference/Action
206 - ELECTRICAL ROUTINE
Powertrain Control System
	Electrical Inputs/Outputs, Transmission Range (TR) Sensor, Vehicle Wiring Harnesses, PCM, Line Pressure Control (LPC) Solenoid, Transmission Fluid Temperature (TFT), Turbine Shaft Speed (TSS)	Run On-Board Diagnostic (OBD). Refer to the Introduction - Gasoline Engines article for diagnosis. Go to Pinpoint Test A , go to Pinpoint Test B , go to Pinpoint Test C and Go to Pinpoint Test D .
Solenoid Body
	Incorrect solenoid body strategy data stored in the PCM	Verify solenoid body strategy data stored in the PCM, download new identification and strategy as necessary. Refer to Solenoid Body Strategy .
306 - HYDRAULIC/MECHANICAL ROUTINE
Transmission Fluid Level
	Low transmission fluid level	Check transmission fluid level and adjust as necessary. Refer to Preliminary Inspection .
	Transmission fluid condition	Carry out transmission fluid condition check. Refer to Preliminary Inspection .
Selector Lever Linkage
	Damaged, out of adjustment	Inspect for damage. Repair as required. Verify selector lever cable adjustment. Refer to AUTOMATIC TRANSAXLE/TRANSMISSION EXTERNAL CONTROLS article.
Incorrect Pressures
	Line Pressure, Line Pressure Control (LPC) Pressure - low	Check pressure at line pressure tap. Carry out Line Pressure and Stall Speed Tests. Refer to Special Testing Procedures . If pressures are low, check the following possible components: Main Control Valve Body, Pump Assembly, and Forward Clutch.
Main Controls
	Plugged Solenoid Body Filter	Inspect for damage. Install new as required.
	Bolts out of torque specification	Tighten bolts to specification.
	Gaskets and Separator Plate - damaged, off location	Inspect for damage. Install new as required.
	Forward Clutch Regulator Valve stuck or damaged	Inspect for damage. Install new as required.
	Forward Clutch Boost Valve stuck or damaged	Inspect for damage. Install new as required.
	Main Regulator Valve - stuck, damaged, missing	Inspect for damage. Repair as required.
	LPC solenoid stuck low	Install a new solenoid body. Refer to Solenoid Body Assembly .
	SSA stuck low	Install a new solenoid body. Refer to Solenoid Body Assembly .
Pump Assembly
	Bolts out of torque specification	Tighten bolts to specification.
	Worn/cross leaks	Inspect for wear and leaks. Install new as required.
Forward Clutch Assembly
	Clutch Plates, Seals, Piston - worn, damaged	Inspect clutches, seals and piston for damage. Install new as required.
	Wave Spring - damaged	Inspect for damage. Install new as required.

ENGAGEMENT CONCERN: NO FORWARD AND NO REVERSE

Possible Component		Reference/Action
207 - ELECTRICAL ROUTINE
	No Electrical Concerns
307 - HYDRAULIC/MECHANICAL ROUTINE
Transmission Fluid Level
	Low transmission fluid level	Check transmission fluid level and adjust as necessary. Refer to Preliminary Inspection .
	Transmission fluid condition	Carry out transmission fluid condition check. Refer to Preliminary Inspection .
Halfshaft
	Splines - worn, damaged	Inspect for damage. Repair as required.
	Shaft - misassembled, incorrect	Inspect for damage. Repair as required.
Selector Lever Linkage (Internal/External)
	Damaged, out of adjustment	Inspect for damage. Repair as required. Verify selector lever cable adjustment. Refer to AUTOMATIC TRANSAXLE/TRANSMISSION EXTERNAL CONTROLS article.
Incorrect Pressures
	Line Pressure, Line Pressure Control (LPC) Pressure - low	Carry out Line Pressure and Stall Tests. Check pressure at the line pressure tap. See the Line Pressure Chart for specifications. If pressures are low, check the following possible components: Transmission Fluid Filter and Seal Assembly, Main Control, Pump Assembly, Low/Reverse Clutch Assembly, Forward Clutch Assembly.
Transmission Fluid Filter and Seal Assembly
	Plugged, damaged, not correctly seated	Inspect for damage. Install a new filter and seal assembly.
	Filter, Seal - damaged	Inspect for damage. Install a new filter and seal assembly.
Main Controls
	Solenoid Body Filter Plugged	Inspect for damage. Install a new filter as required.
	Manual Valve	Inspect for damage. Install new as required.
	Shift Valves	Inspect for damage. Install new as required.
	Bolts out of torque specification	Tighten bolts to specification.
	Gaskets and Separator Plate - damaged, off location	Inspect for damage. Install new as required.
	Main Regulator Valve (only if line pressure is out of specification) - damaged	Inspect for damage. Repair as required.
	Components - damaged, check balls stuck	Inspect for damage. Repair as required.
Pump Assembly
	Bolts out of torque specification	Tighten bolts to specification.
	Porosity/cross leaks - leaking, plugged hole	Install a new pump assembly.
	Components damaged - Chain, Sprocket or Shaft Broken	Inspect for damage. Install new as required.
Output Shaft
	Splines - damaged	Inspect for damage. Repair as required.
Other Possible Components
	Turbine Shaft	Inspect for damage. Repair as required.
	Pump Shaft, Sprockets and Drive Chain	Inspect for damage. Repair as required.
	Flexplate	Inspect for damage. Repair as required.
	Sun Gear and Shell Assemblies	Inspect for damage. Repair as required.
	Planetaries	Inspect for damage. Repair as required.
	Final Drive Assembly	Inspect for damage. Repair as required.

ENGAGEMENT CONCERN: DELAYED/SOFT FORWARD AND REVERSE

Possible Component		Reference/Action
209 - ELECTRICAL ROUTINE
Powertrain Control System
	Electrical Inputs/Outputs, Transmission Range (TR) Sensor, Transmission Fluid Temperature (TFT) Sensor, Turbine Shaft Speed (TSS) Sensor, Line Pressure Control (LPC) Solenoid, Vehicle Wiring Harnesses, PCM	Run On-Board Diagnostic (OBD). Refer to Introduction - Gasoline Engines article for diagnosis. Go to Pinpoint Test A , go to Pinpoint Test B , go to Pinpoint Test C and Go to Pinpoint Test D .
Solenoid Body
	Incorrect solenoid body strategy data stored in the PCM	Verify solenoid body strategy data stored in the PCM, download new identification and strategy as necessary. Refer to Solenoid Body Strategy .
309 - HYDRAULIC/MECHANICAL ROUTINE
Transmission Fluid Level
	Low transmission fluid level	Check transmission fluid level and adjust as necessary. Refer to Preliminary Inspection .
	Transmission fluid condition	Carry out transmission fluid condition check. Refer to Preliminary Inspection .
Selector Lever Linkage (Internal/External)
	Damaged, out of adjustment	Inspect for damage. Repair as required. Verify selector lever cable adjustment. Refer to AUTOMATIC TRANSAXLE/TRANSMISSION EXTERNAL CONTROLS article.
Incorrect Pressures
	Line Pressure, LPC Pressure - low	Carry out Line Pressure and Stall Speed Tests. Refer to Special Testing Procedures . See the Line Pressure Chart for specifications. If pressures are low, check the following possible components: Main Control, Pump Assembly and LPC solenoid.
Transmission Fluid Filter and Seal Assembly
	Plugged, damaged, not correctly seated	Inspect for damage. Install a new filter and seal assembly.
	Filter, Seal - damaged	Inspect for damage. Install a new filter and seal assembly.
Main Controls
	Bolts out of torque specification	Tighten bolts to specification.
	Gaskets and Separator Plate - damaged, off location	Inspect for damage. Install new as required.
	Seals, Manual Valve, Main Regulator Valve - missing, damaged or misassembled	Inspect for damage. Repair or install new as required.
Pump Assembly
	Bolts out of torque specification	Tighten bolts to specification.
	Worn/cross leaks - leaking	Install a new pump assembly.
	Components damaged	Inspect for damage. Install new as required.

SHIFT CONCERNS: SOME OR ALL SHIFTS MISSING

Possible Component		Reference/Action
210 - ELECTRICAL ROUTINE
Powertrain Control System
	Electrical Inputs/Outputs, Vehicle Wiring Harnesses, PCM, Shift Solenoid A (SSA), Shift Solenoid B (SSB), Shift Solenoid C (SSC), Shift Solenoid D (SSD), Shift Solenoid E (SSE), Throttle Position (TP), Mass Air Flow (MAF), Output Shaft Speed (OSS), Turbine Shaft Speed (TSS), Transmission Range (TR) Sensor, Line Pressure Control (LPC) Solenoid	Run On-Board Diagnostic (OBD). Refer to the Introduction - Gasoline Engines article for diagnosis. Go to Pinpoint Test A , go to Pinpoint Test C and Go to Pinpoint Test D .
310 - HYDRAULIC/MECHANICAL ROUTINE
Transmission Fluid Level
	Incorrect transmission fluid level	Check transmission fluid level and adjust as necessary. Refer to Preliminary Inspection .
	Transmission fluid condition	Carry out transmission fluid condition check. Refer to Preliminary Inspection .
Selector Lever Linkage (Internal/External)
	Damaged, out of adjustment	Inspect for damage. Repair as required. Verify selector lever cable adjustment. Refer to AUTOMATIC TRANSAXLE/TRANSMISSION EXTERNAL CONTROLS article.
Vehicle Speed Input
	Insufficient, erratic or no input received by the PCM from the OSS sensor	Inspect for damage. Repair as required. Go to Pinpoint Test C .
Transmission Fluid Filter and Seal Assembly
	Plugged, damaged, not correctly seated	Inspect for damage. Install a new filter and seal assembly.
	Filter, Seal - damaged	Inspect for damage. Install a new filter and seal assembly.
Main Controls
	Regulator and/or Boost Valves - stuck, damaged, misassembled	Inspect for damage. Repair or install new as required.
	Plugged Solenoid Body Filter	Inspect for damage. Install new as required.
End Cover
	End Cover Gasket - leaking	Inspect for damage. Repair or install new as required.
Planetary Gear Sets
	Damaged	Inspect for damage. Repair as required.
One-Way Clutch Assembly
	Damaged	Inspect for damage. Repair as required.
Other Components
	Clutches	Inspect for damage. Repair as required.
	Output Shafts (Differential)	Inspect for damage. Repair as required.
	Powerflow Components	Inspect for damage. Repair as required.
	Go to Shift Concerns:	See the appropriate shift concern and routine: Shift Concern: No 1-2, Routine 220/320 Shift Concern: No 2-3, Routine 221/321 Shift Concern: No 3-4, Routine 222/322 Shift Concern: No 4-5, Routine 223/323 Shift Concern: No 5-6, Routine 224/324 Shift Concern: No 6-5, Routine 225/325 Shift Concern: No 5-4, Routine 226/326 Shift Concern: No 4-3, Routine 227/327 Shift Concern: No 3-2, Routine 228/328 Shift Concern: No 2-1, Routine 229/329

SHIFT CONCERNS: TIMING - EARLY/LATE

Possible Component		Reference/Action
211 - ELECTRICAL ROUTINE
Powertrain Control System
	Electrical Inputs/Outputs, Vehicle Wiring Harnesses, PCM, Shift Solenoid A (SSA), Shift Solenoid B (SSB), Shift Solenoid C (SSC), Shift Solenoid D (SSD), Shift Solenoid E (SSE), Throttle Position (TP), Mass Air Flow (MAF), Output Shaft Speed (OSS), Intake Air Temperature (IAT), Engine Coolant Temperature (ECT), Transmission Fluid Temperature (TFT), Turbine Shaft Speed (TSS), Internal Wire Harness, Line Pressure Control (LPC) Solenoid	Run On-Board Diagnostic (OBD). Refer to Introduction - Gasoline Engines article for diagnosis. Go to Pinpoint Test A , go to Pinpoint Test B and Go to Pinpoint Test C .
		Carry out Shift Point Road Test. Refer to Shift Point Road Test . and carry out Torque Converter Operation Test. Refer to Torque Converter Diagnosis .
Solenoid Body
	Incorrect solenoid body strategy data stored in the PCM	Verify solenoid body strategy data stored in the PCM, download new identification and strategy as necessary. Refer to Solenoid Body Strategy .
311 - HYDRAULIC/MECHANICAL ROUTINE
Other
	Tire Size	See the specification decal and verify vehicle has original equipment. Changes in tire size will affect shift timing.
Transmission Fluid Level
	Low transmission fluid level	Check transmission fluid level and adjust as necessary. Refer to Preliminary Inspection .
	Transmission fluid condition	Carry out transmission fluid condition check. Refer to Preliminary Inspection .
Selector Lever Linkage (Internal/External)
	Damaged, out of adjustment	Inspect for damage. Repair as required. Verify selector lever cable adjustment. Refer to AUTOMATIC TRANSAXLE/TRANSMISSION EXTERNAL CONTROLS article.
Main Controls
	Plugged Solenoid Body Filter	Inspect for damage. Install new as required.
	Bolts out of torque specification	Tighten bolts to specification.
	Gaskets and Separator Plate - damaged, off location	Inspect for damage. Install new as required.
	Valves, Accumulators, Seals, Springs, Clips, Check balls - damaged, missing, misassembled	Inspect for damage. Repair as required.
		See the appropriate shift concern and routine for further diagnosis: Shift Concern: Soft/Slipping 1-2, Routine 230/330 Shift Concern: Soft/Slipping 2-3, Routine 231/331 Shift Concern: Soft/Slipping 3-4, Routine 232/332 Shift Concern: Soft/Slipping 4-5, Routine 233/333 Shift Concern: Soft/Slipping 5-6, Routine 234/334 Shift Concern: Soft/Slipping 6-5, Routine 235/335 Shift Concern: Soft/Slipping 5-4, Routine 236/336 Shift Concern: Soft/Slipping 4-3, Routine 237/337 Shift Concern: Soft/Slipping 3-2, Routine 238/338 Shift Concern: Soft/Slipping 2-1, Routine 239/339
End Cover
	End Cover Gasket - leaking	Inspect for damage. Repair or install new as required.
Planetary Gear Sets
	Damaged	Inspect for damage. Repair or install new as required.
One-Way Clutch Assembly
	Damaged	Inspect for damage. Repair or install new as required.
Other Components
	Clutches	Inspect for damage. Repair or install new as required.
	Output Shaft (Differential)	Inspect for damage. Repair or install new as required.
	Powerflow Components	Inspect for damage. Repair as required.
Vehicle Speed Input
	Insufficient, erratic or no input received by the PCM from the OSS or TSS sensors	Inspect for damage. Repair as required. Go to Pinpoint Test C .
Transmission Fluid Filter and Seal Assembly
	Plugged, damaged, not correctly seated	Inspect for damage. Install a new filter and seal assembly.
	Filter, Seal - damaged	Inspect for damage. Install a new filter and seal assembly.

SHIFT CONCERNS: TIMING - ERRATIC/HUNTING

Possible Component		Reference/Action
212 - ELECTRICAL ROUTINE
Powertrain Control System
	Electrical Inputs/Outputs, Vehicle Wiring Harnesses, PCM, Torque Converter Clutch (TCC) and Shift Solenoid A (SSA), Shift Solenoid B (SSB), Shift Solenoid C (SSC), Shift Solenoid D (SSD), Shift Solenoid E (SSE), Throttle Position (TP), Output Shaft Speed (OSS), Engine Coolant Temperature (ECT), Intake Air Temperature (IAT), Mass Air Flow (MAF), Transmission Range (TR), Transmission Fluid Temperature (TFT), Turbine Shaft Speed (TSS), Sensors	Run On-Board Diagnostic (OBD). Refer to Introduction - Gasoline Engines article for diagnosis. Go to Pinpoint Test A , go to Pinpoint Test B , go to Pinpoint Test C , Go to Pinpoint Test D and Go to Pinpoint Test E .
		Carry out Shift Point Road Test. Refer to Shift Point Road Test . and carry out Torque Converter Operation Test. Refer to Torque Converter Diagnosis .
Solenoid Body
	Incorrect solenoid body strategy data stored in the PCM	Verify solenoid body strategy data stored in the PCM, download new identification and strategy as necessary. Refer to Solenoid Body Strategy .
312 - HYDRAULIC/MECHANICAL ROUTINE
Transmission Fluid Level
	Low transmission fluid level	Check transmission fluid level and adjust as necessary. Refer to Preliminary Inspection .
	Transmission fluid condition	Carry out transmission fluid condition check. Refer to Preliminary Inspection .
Selector Lever Linkage (Internal/External)
	Damaged, out of adjustment	Inspect for damage. Repair as required. Verify selector lever cable adjustment. Refer to AUTOMATIC TRANSAXLE/TRANSMISSION EXTERNAL CONTROLS article.
Main Control Valve Body
	Plugged Solenoid Body Filter	Inspect for damage. Install new as required.
	Bolts out of torque specification	Tighten bolts to specification.
	Gaskets and Separator Plate - damaged, off location	Inspect for damage. Install new as required.
	Valves, Seals, Clips, Check Ball - stuck, damaged, contaminated	Inspect for damage. Repair or install new as required.
End Cover
	End Cover Gasket - leaking	Inspect for damage. Repair or install new as required.
Vehicle Speed Input
	Insufficient, erratic or no input received by the PCM from the OSS or TSS sensor	Inspect for damage. Repair as required. Go to Pinpoint Test C .
Torque Converter Clutch (TCC)
		See Torque Converter Cycling (Routine 254/354).
Planetary Gear Sets
	Damaged	Inspect for damage. Repair as required.
Clutch Assemblies
	Damaged Clutch Plates, Pistons, Seals, Return Springs	Inspect for damage. Repair or install new as required.
Transmission Fluid Filter and Seal Assembly
	Plugged, damaged, not correctly seated	Inspect for damage. Install a new filter and seal assembly.
	Filter, Seal - damaged	Inspect for damage. Install a new filter and seal assembly.
For Diagnosis Related to a Specific Shift
		See the appropriate shift concern and routine for further diagnosis:
		Shift Concern: No 1-2, Routine 220/320 Shift Concern: No 2-3, Routine 221/321 Shift Concern: No 3-4, Routine 222/322 Shift Concern: No 4-5, Routine 223/323 Shift Concern: No 5-6, Routine 224/324 Shift Concern: No 6-5, Routine 225/325 Shift Concern: No 5-4, Routine 226/326 Shift Concern: No 4-3, Routine 227/327 Shift Concern: No 3-2, Routine 228/328 Shift Concern: No 2-1, Routine 229/329 Shift Concern: Soft/Slip 1-2, Routine 230/330 Shift Concern: Soft/Slip 2-3, Routine 231/331 Shift Concern: Soft/Slip 3-4, Routine 232/332 Shift Concern: Soft/Slip 4-5, Routine 233/333 Shift Concern: Soft/Slip 5-6, Routine 234/334 Shift Concern: Soft/Slip 6-5, Routine 235/335 Shift Concern: Soft/Slip 5-4, Routine 236/336 Shift Concern: Soft/Slip 4-3, Routine 237/337 Shift Concern: Soft/Slip 3-2, Routine 238/338 Shift Concern: Soft/Slip 2-1, Routine 239/339 Shift Concern: Harsh 1-2, Routine 240/340 Shift Concern: Harsh 2-3, Routine 241/341 Shift Concern: Harsh 3-4, Routine 242/342 Shift Concern: Harsh 4-5, Routine 243/343 Shift Concern: Harsh 5-6, Routine 244/344 Shift Concern: Harsh 6-5, Routine 245/345 Shift Concern: Harsh 5-4, Routine 246/346 Shift Concern: Harsh 4-3, Routine 247/347 Shift Concern: Harsh 3-2, Routine 248/348 Shift Concern: Harsh 2-1, Routine 249/349

SHIFT CONCERNS: FEEL - SOFT/SLIPPING

Possible Component		Reference/Action
213 - ELECTRICAL ROUTINE
Powertrain Control System
	Electrical Inputs/Outputs, Vehicle Wiring Harnesses, PCM, Line Pressure Control (LPC) Solenoid, Mass Air Flow (MAF), Throttle Position (TP), Engine Coolant Temperature (ECT), Intake Air Temperature (IAT), Transmission Fluid Temperature (TFT), Turbine Shaft Speed (TSS), Output Shaft Speed (OSS)	Run On-Board Diagnostic (OBD). Refer to Introduction - Gasoline Engines article for diagnosis. Go to Pinpoint Test A , go to Pinpoint Test B and Go to Pinpoint Test C .
Solenoid Body
	Incorrect solenoid body strategy data stored in the PCM	Verify solenoid body strategy data stored in the PCM, download new identification and strategy as necessary. Refer to Solenoid Body Strategy .
313 - HYDRAULIC/MECHANICAL ROUTINE
Transmission Fluid
	Low transmission fluid level	Check transmission fluid level and adjust as necessary. Refer to Preliminary Inspection .
	Transmission fluid condition	Carry out transmission fluid condition check. Refer to Preliminary Inspection .
Selector Lever Linkage (Internal/External)
	Damaged, out of adjustment	Inspect for damage. Repair as required. Verify selector lever cable adjustment. Refer to AUTOMATIC TRANSAXLE/TRANSMISSION EXTERNAL CONTROLS article.
Incorrect Pressures
	Low LPC pressure	Check pressures at line pressure taps. Carry out Line Pressure and Stall Speed Tests. Refer to Special Testing Procedures . See the Line Pressure Chart for specification. If pressures are low or all shifts are soft/slipping refer to Main Control .
		If pressures are OK and a specific shift is soft/slipping, see the following chart: Soft/Slipping Shift 1-2, Routine 230/330 Soft/Slipping Shift 2-3, Routine 231/331 Soft/Slipping Shift 3-4, Routine 232/332 Soft/Slipping Shift 4-5, Routine 233/333 Soft/Slipping Shift 5-6, Routine 234/334 Soft/Slipping Shift 6-5, Routine 235/335 Soft/Slipping Shift 5-4, Routine 236/336 Soft/Slipping Shift 4-3, Routine 237/337 Soft/Slipping Shift 3-2, Routine 238/338 Soft/Slipping Shift 2-1, Routine 239/339
Transmission Fluid Filter and Seal Assembly
	Plugged, damaged, not correctly seated	Inspect for damage. Install a new filter and seal assembly.
	Filter, Seal - damaged	Inspect for damage. Install a new filter and seal assembly.
Main Controls
	Plugged Solenoid Body Filter	Inspect for damage. Install new as required.
	Bolts out of torque specification	Tighten bolts to specification.
	Gaskets and Separator Plate - damaged, off location	Inspect for damage. Install new as required.
	Sticking or Binding Valves, Check Balls, Clips, Springs - damaged, missing	Inspect for damage. Repair or install new as required.
Pump Assembly
	Pump Assembly - worn/cross leaks, leaking	Inspect for damage. Install new as required.

SHIFT CONCERNS: FEEL - HARSH

Possible Component		Reference/Action
214 - ELECTRICAL ROUTINE
Powertrain Control System
	Electrical Inputs/Outputs, Vehicle Wiring Harnesses, PCM, Line Pressure Control (LPC) Solenoid, Mass Air Flow (MAF), Throttle Position (TP), Output Shaft Speed (OSS), Turbine Shaft Speed (TSS), Engine Coolant Temperature (ECT), Intake Air Temperature (IAT), Power Steering Pressure (PSP), Transmission Fluid Temperature (TFT), Transmission Range (TR) Sensor, Shift Solenoid A (SSA), Shift Solenoid B (SSB), Shift Solenoid C (SSC), Shift Solenoid D (SSD) and Shift Solenoid E (SSE)	Run On-Board Diagnostic (OBD). Refer to Introduction - Gasoline Engines article for diagnosis. Go to Pinpoint Test A , go to Pinpoint Test B , go to Pinpoint Test C and Go to Pinpoint Test D .
Solenoid Body
	Incorrect solenoid body strategy data stored in the PCM	Verify solenoid body strategy data stored in the PCM, download new identification and strategy as necessary. Refer to Solenoid Body Strategy .
314 - HYDRAULIC/MECHANICAL ROUTINE
Transmission Fluid Level
	Low transmission fluid level	Check transmission fluid level and adjust as necessary. Refer to Preliminary Inspection .
	Transmission fluid condition	Carry out transmission fluid condition check. Refer to Preliminary Inspection .
Incorrect Pressures
	High LPC pressure	Check pressure at line pressure tap. Carry out Line Pressure Test. Refer to Special Testing Procedures . See the Line Pressure Chart for specifications. If pressures are high or all shifts are harsh, go to Main Control. Refer to Main Control . If pressures are OK and a specific shift is harsh. See the appropriate shift routine in the following chart: Shift 1-2, Routine 240/340 Shift 2-3, Routine 241/341 Shift 3-4, Routine 242/342 Shift 4-5, Routine 243/343 Shift 5-6, Routine 244/344 Shift 6-5, Routine 245/345 Shift 5-4, Routine 246/346 Shift 4-3, Routine 247/347 Shift 3-2, Routine 248/348 Shift 2-1, Routine 249/349
Main Control Valve Body
	Plugged Solenoid Body Filter	Inspect for damage. Install new as required.
	Bolts out of torque specification	Tighten bolts to specification.
	Gaskets and Separator Plate - damaged, off location	Inspect for damage. Install new as required.
	Valves, Springs, Clips, Check Balls - stuck, damaged	Inspect for damage. Repair or install new as required.
Pump Assembly
	Pump Assembly - worn/cross leaks, leaking	Inspect for damage. Install new as required.

SHIFT CONCERNS: NO 1ST GEAR, ENGAGES IN HIGHER GEAR

Possible Component		Reference/Action
215 - ELECTRICAL ROUTINE
Powertrain Control System
	Electrical Inputs/Outputs, Vehicle Wiring Harnesses, PCM, Shift Solenoid A (SSA), Shift Solenoid B (SSB), Shift Solenoid C (SSC), Shift Solenoid D (SSD), Shift Solenoid E (SSE), Output Shaft Speed (OSS) and Turbine Shaft Speed (TSS) sensor, transaxle solenoid power control circuit - no voltage at transaxle connector	Run On-Board Diagnostic (OBD). Refer to Introduction - Gasoline Engines article for diagnosis. Go to Pinpoint Test A ,Go to Pinpoint Test C and Go to Pinpoint Test E . Repair as required. Clear codes. Road Test and rerun On-Board Diagnostic (OBD).
315 - HYDRAULIC/MECHANICAL ROUTINE
Main Control Valve Body
	Plugged Solenoid Body Filter (SSA Filter Plate)	Inspect for damage. Install new as required.
	Bolts out of torque specification	Tighten bolts to specification.
	Gaskets and Separator Plate - damaged, off location	Inspect for damage. Install new as required.
	Forward Clutch Regulator Valve, Springs, Clips - stuck, damaged, missing, misassembled	Inspect for damage. Repair as required.
	Shift Solenoid - stuck, damaged	Inspect for damage. Go to Pinpoint Test A . Repair as required. Activate solenoid using the scan tool. Repair as required.
	For diagnosis related to a specific gear, use the scan tool to select the gear	See the following routines: Shift 1-2, Routine 220/320 Shift 2-3, Routine 221/321 Shift 3-4, Routine 222/322 Shift 4-5, Routine 223/323 Shift 5-6, Routine 224/324
Mechanical
	Clutches or Seals - damaged or worn	Inspect for damage. Repair or install new as required.

SHIFT CONCERNS: NO MANUAL LOW - 1ST GEAR

Possible Component		Reference/Action
216 - ELECTRICAL ROUTINE
Powertrain Control System
	Electrical Inputs/Outputs, Vehicle Wiring Harnesses, PCM, Shift Solenoid A (SSA), Shift Solenoid D (SSD), Shift Solenoid E (SSE), Transmission Range (TR) sensor	Run On-Board Diagnostic (OBD). Refer to Introduction - Gasoline Engines article for diagnosis. Go to Pinpoint Test A and Go to Pinpoint Test D . Repair as required. Clear codes. Road Test and rerun On-Board Diagnostic (OBD).
316 - HYDRAULIC/MECHANICAL ROUTINE
Selector Lever Linkage (Internal/External)
	Damaged or out of adjustment	Inspect for damage. Repair as required. Verify selector lever cable adjustment. Refer to AUTOMATIC TRANSAXLE/TRANSMISSION EXTERNAL CONTROLS article.
Incorrect Pressures
	Low LPC pressure	Check pressure at line pressure tap. Carry out Line Pressure Test. Refer to Special Testing Procedures . See the Line Pressure Chart for specifications. If pressures are low, check the following possible components: Main Control. Refer to Main Control .
Main Control Valve Body
	Bolts out of torque specification	Tighten bolts to specification.
	Gaskets and Separator Plate - damaged, off location	Inspect for damage. Install new as required.
	Forward Boost, Forward Regulator, Low/Reverse Boost, Low/Reverse Regulator Valves, Clips - stuck, damaged, missing	Inspect for damage. Repair as required.
	Multiplex Shift Valve and Multiplex Manual Valve, Clips - stuck, damaged, missing	Check 4th gear ratio. Inspect for damage. Repair as required.
	Check Ball - damaged, missing	Inspect for damage. Repair as required.
Low/Reverse Clutch Assembly
	Seals, Piston, Spring - damaged	Inspect for damage. Repair or install new as required.
	Clutches - damaged, burnt, worn	Inspect for damage. Install new as required.
	Worn, damaged, misassembled	Inspect for damage. Repair as required.
Forward Clutch Assembly
	Seals, Piston, Spring - damaged	Inspect for damage. Repair or install new as required.
	Clutches - damaged, burnt, worn	Inspect for damage. Install new as required.
	Worn, damaged, misassembled	Inspect for damage. Repair as required.
	Case - damaged	Inspect for damage. Repair as required.

SHIFT CONCERNS: NO 1-2 SHIFT (AUTOMATIC)

Possible Component		Reference/Action
220 - ELECTRICAL ROUTINE
Powertrain Control System
	Electrical Inputs/Outputs, Vehicle Wiring Harnesses, PCM, Shift Solenoid C (SSC) and Transmission Range (TR) Sensor	Run On-Board Diagnostic (OBD). Refer to Introduction - Gasoline Engines article for diagnosis. Go to Pinpoint Test A and Go to Pinpoint Test D .
320 - HYDRAULIC/MECHANICAL ROUTINE
Incorrect Pressures
	Line pressure	Check pressure at line pressure tap. Carry out Line Pressure Test. Refer to Special Testing Procedures . See the Line Pressure Chart for specifications. If not OK, check Main Control. Refer to Main Control .
Main Control Valve Body
	Bolts out of torque specification	Tighten bolts to specification.
	Gaskets and Separator Plate - damaged, off location	Inspect for damage. Install new as required.
	Intermediate Regulator Valve, Springs, Clips - loose, stuck, missing, misassembled stuck off	Inspect for damage. Repair or install new as required.
	SSC not functioning correctly	Activate solenoid using scan tool. Refer to Output State Control (OSC) Mode . Go to Pinpoint Test A . Install a new solenoid body. Refer to Solenoid Body Assembly . Download a new solenoid body strategy into the PCM. Refer to Solenoid Body Strategy .
Intermediate Clutch Assembly - Failed Off
	Seals - damaged	Inspect for damage. Install new as required.
	Piston - damaged	Inspect for damage. Install new as required.
	Friction - damaged, worn	Inspect for damage. Install new as required.
	Cylinder Hub - damaged	Inspect for damage. Install new as required.
	Return Spring Assembly - damaged	Inspect for damage. Install new as required.
Low/Reverse Clutch Assembly - Failed On
	Piston - damaged	Inspect for damage. Install new as required.
	Friction - overheated	Inspect for damage. Install new as required.
	Cylinder Hub - damaged	Inspect for damage. Install new as required.
	Return Spring Assembly - damaged	Inspect for damage. Install new as required.
Pump Assembly
	Worn/cross leaks	Inspect for damage. Install new as required.
	Component damaged	Inspect for damage. Install a new pump assembly as required.
Low One-Way Clutch Assembly
	Not overrunning, damaged	Inspect for damage. Install new as required.
Planetary Carrier
	Damaged	Inspect for damage. Install new as required.

SHIFT CONCERNS: NO 2-3 SHIFT (AUTOMATIC)

Possible Component		Reference/Action
221 - ELECTRICAL ROUTINE
Powertrain Control System
	Electrical Inputs/Outputs, Vehicle Wiring Harnesses, PCM, Shift Solenoid B (SSB) Failed, Shift Solenoid C (SSC) Stuck On and Transmission Range (TR) Sensor	Run On-Board Diagnostic (OBD). Refer to Introduction - Gasoline Engines article for diagnosis. Go to Pinpoint Test A and Go to Pinpoint Test D .
321 - HYDRAULIC/MECHANICAL ROUTINE
Incorrect Pressures
	Line pressure	Check pressure at line pressure tap. Carry out Line Pressure Test. Refer to Special Testing Procedures . See the Line Pressure Chart for specifications. If not OK, check Main Control. Refer to Main Control .
Main Control Valve Body
	Bolts out of torque specification	Tighten bolts to specification.
	Gaskets and Separator Plate - damaged, off location	Inspect for damage. Install new as required.
	Direct Regulator and Boost Valves, Springs, Clips - loose, stuck, missing, misassembled, stuck off	Inspect for damage. Repair or install new as required.
	Intermediate Regulator and Boost Valves, Springs, Clips - loose, stuck, missing, misassembled, stuck on	Inspect for damage. Repair or install new as required.
	SSB or SSC not functioning correctly	Activate solenoid using scan tool. Refer to Output State Control (OSC) Mode . Go to Pinpoint Test A . Install a new solenoid body. Refer to Solenoid Body Assembly . Download a new solenoid body strategy into the PCM. Refer to Solenoid Body Strategy .
Direct Clutch Assembly - Failed Off
	Seals - damaged	Inspect for damage. Install new as required.
	Piston - damaged	Inspect for damage. Install new as required.
	Friction - damaged, worn	Inspect for damage. Install new as required.
	Cylinder Hub - damaged	Inspect for damage. Install new as required.
	Return Spring Assembly - damaged	Inspect for damage. Install new as required.
Intermediate Clutch Assembly - Failed On
	Seals - damaged	Inspect for damage. Install new as required.
	Piston - damaged	Inspect for damage. Install new as required.
	Friction - damaged, worn	Inspect for damage. Install new as required.
	Cylinder Hub - damaged	Inspect for damage. Install new as required.
	Return Spring Assembly - damaged	Inspect for damage. Install new as required.

SHIFT CONCERNS: NO 3-4 SHIFT (AUTOMATIC)

Possible Component		Reference/Action
222 - ELECTRICAL ROUTINE
Powertrain Control System
	Electrical Inputs/Outputs, Vehicle Wiring Harnesses, PCM, Shift Solenoid D (SSD) Failed, Shift Solenoid B (SSB) Stuck On and Transmission Range (TR) Sensor	Run On-Board Diagnostic (OBD). Refer to Introduction - Gasoline Engines article for diagnosis. Go to Pinpoint Test A and Go to Pinpoint Test D .
322 - HYDRAULIC/MECHANICAL ROUTINE
Main Control Valve Body
	Bolts out of torque specification	Tighten bolts to specification.
	Gaskets and Separator Plate - damaged, off location	Inspect for damage. Install new as required.
	Overdrive Regulator and Boost Valves, Springs, Clips - loose, stuck, missing, misassembled, clutch failed off	Inspect for damage. Repair or install new as required.
	Direct Regulator and Boost Valves, Springs, Clips - loose, stuck, missing, misassembled, clutch failed on	Inspect for damage. Repair or install new as required.
	SSD not functioning correctly, SSB stuck on	Activate solenoid using scan tool. Refer to Output State Control (OSC) Mode . Go to Pinpoint Test A . Install a new solenoid body. Refer to Solenoid Body Assembly . Download a new solenoid body strategy into the PCM. Refer to Solenoid Body Strategy .
Overdrive Clutch Assembly - Failed Off
	Seals - damaged	Inspect for damage. Install new as required.
	Piston - damaged	Inspect for damage. Install new as required.
	Friction - damaged, worn	Inspect for damage. Install new as required.
	Cylinder Hub - damaged	Inspect for damage. Install new as required.
	Return Spring Assembly - damaged	Inspect for damage. Install new as required.
Direct Clutch Assembly - Failed On
	Seals - damaged	Inspect for damage. Install new as required.
	Piston - damaged	Inspect for damage. Install new as required.
	Friction - damaged, worn	Inspect for damage. Install new as required.
	Cylinder Hub - damaged	Inspect for damage. Install new as required.
	Return Spring Assembly - damaged	Inspect for damage. Install new as required.

SHIFT CONCERNS: NO 4-5 SHIFT (AUTOMATIC)

Possible Component		Reference/Action
223 - ELECTRICAL ROUTINE
Powertrain Control System
	Electrical Inputs/Outputs, Vehicle Wiring Harnesses, PCM, Shift Solenoid B (SSB) Failed, Shift Solenoid A (SSA) Stuck On, Transmission Range (TR) Sensor	Run On-Board Diagnostic (OBD). Refer to Introduction - Gasoline Engines article for diagnosis. Go to Pinpoint Test A and Go to Pinpoint Test D .
Transmission Control Switch (TCS)/Overdrive (O/D) Cancel Switch
	Switch control circuit open/shorted, switch damaged	Refer to AUTOMATIC TRANSAXLE/TRANSMISSION EXTERNAL CONTROLS article.
323 - HYDRAULIC/MECHANICAL ROUTINE
Main Control Valve Body
	Bolts out of torque specification	Tighten bolts to specification.
	Gaskets and Separator Plate - damaged, off location	Inspect for damage. Install new as required.
	Direct Regulator and Boost Valves, Springs, Clips - loose, stuck, missing, misassembled, clutch failed off	Inspect for damage. Repair or install new as required.
	Forward Regulator and Boost Valves, Springs, Clips - loose, stuck, missing, misassembled, clutch failed on	Inspect for damage. Repair or install new as required.
	SSB not functioning correctly, SSA stuck on	Activate solenoid using scan tool. Refer to Output State Control (OSC) Mode . Go to Pinpoint Test A . Install a new solenoid body. Refer to Solenoid Body Assembly . Download a new solenoid body strategy into the PCM. Refer to Solenoid Body Strategy .
Direct Clutch Assembly - Failed Off
	Seals - damaged	Inspect for damage. Install new as required.
	Piston - damaged	Inspect for damage. Install new as required.
	Friction - damaged, worn	Inspect for damage. Install new as required.
	Cylinder Hub - damaged	Inspect for damage. Install new as required.
	Return Spring Assembly - damaged	Inspect for damage. Install new as required.
Forward Clutch Assembly - Failed On
	Seals - damaged	Inspect for damage. Install new as required.
	Piston - damaged	Inspect for damage. Install new as required.
	Friction - damaged, worn	Inspect for damage. Install new as required.
	Cylinder Hub - damaged	Inspect for damage. Install new as required.
	Return Spring Assembly - damaged	Inspect for damage. Install new as required.

SHIFT CONCERNS: NO 5-6 SHIFT (AUTOMATIC)

Possible Component		Reference/Action
224 - ELECTRICAL ROUTINE
Powertrain Control System
	Electrical Inputs/Outputs, Vehicle Wiring Harnesses, PCM, Shift Solenoid C (SSC) Failed, Shift Solenoid B (SSB) Stuck On, Transmission Range (TR) Sensor	Run On-Board Diagnostic (OBD). Refer to Introduction - Gasoline Engines article for diagnosis. Go to Pinpoint Test A and Go to Pinpoint Test D .
Transmission Control Switch (TCS)/Overdrive (O/D) Cancel Switch
	Switch control circuit open/shorted, switch damaged	Refer to AUTOMATIC TRANSAXLE/TRANSMISSION EXTERNAL CONTROLS article.
324 - HYDRAULIC/MECHANICAL ROUTINE
Main Control Valve Body
	Bolts out of torque specification	Tighten bolts to specification.
	Gaskets and Separator Plate - damaged, off location	Inspect for damage. Install new as required.
	Intermediate Regulator and Boost Valves, Springs, Clips - loose, stuck, missing, misassembled, clutch failed off	Inspect for damage. Repair or install new as required.
	Direct Regulator and Boost Valves, Springs, Clips - loose, stuck, missing, misassembled, clutch failed on	Inspect for damage. Repair or install new as required.
	SSC not functioning correctly, SSB stuck on	Activate solenoid using scan tool. Refer to Output State Control (OSC) Mode . Go to Pinpoint Test A . Install a new solenoid body. Refer to Solenoid Body Assembly . Download a new solenoid body strategy into the PCM. Refer to Solenoid Body Strategy .
Intermediate Clutch Assembly - Failed Off
	Seals - damaged	Inspect for damage. Install new as required.
	Piston - damaged	Inspect for damage. Install new as required.
	Friction - damaged, worn	Inspect for damage. Install new as required.
	Cylinder Hub - damaged	Inspect for damage. Install new as required.
	Return Spring Assembly - damaged	Inspect for damage. Install new as required.
Direct Clutch Assembly - Failed On
	Seals - damaged	Inspect for damage. Install new as required.
	Piston - damaged	Inspect for damage. Install new as required.
	Friction - damaged, worn	Inspect for damage. Install new as required.
	Cylinder Hub - damaged	Inspect for damage. Install new as required.
	Return Spring Assembly - damaged	Inspect for damage. Install new as required.

SHIFT CONCERNS: NO 6-5 SHIFT (AUTOMATIC)

Possible Component		Reference/Action
225 - ELECTRICAL ROUTINE
Powertrain Control System
	Electrical Inputs/Outputs, Vehicle Wiring Harnesses, PCM, Shift Solenoid B (SSB) Failed, Shift Solenoid C (SSC) Stuck On, Transmission Range (TR) Sensor	Run On-Board Diagnostic (OBD). Refer to Introduction - Gasoline Engines article for diagnosis. Go to Pinpoint Test A and Go to Pinpoint Test D .
325 - HYDRAULIC/MECHANICAL ROUTINE
Main Control Valve Body
	Bolts out of torque specification	Tighten bolts to specification.
	Gaskets and Separator Plate - damaged, off location	Inspect for damage. Install new as required.
	Intermediate Regulator and Boost Valves, Springs, Clips - loose, stuck, missing, misassembled, clutch failed on	Inspect for damage. Repair or install new as required.
	Direct Regulator and Boost Valves, Springs, Clips - loose, stuck, missing, misassembled, clutch failed off	Inspect for damage. Repair or install new as required.
	SSC not functioning correctly, SSB stuck on	Activate solenoid using scan tool. Refer to Output State Control (OSC) Mode . Go to Pinpoint Test A . Install a new solenoid body. Refer to Solenoid Body Assembly . Download a new solenoid body strategy into the PCM. Refer to Solenoid Body Strategy .
Intermediate Clutch Assembly - Failed On
	Seals - damaged	Inspect for damage. Install new as required.
	Piston - damaged	Inspect for damage. Install new as required.
	Friction - damaged, worn	Inspect for damage. Install new as required.
	Cylinder Hub - damaged	Inspect for damage. Install new as required.
	Return Spring Assembly - damaged	Inspect for damage. Install new as required.
Direct Clutch Assembly - Failed Off
	Seals - damaged	Inspect for damage. Install new as required.
	Piston - damaged	Inspect for damage. Install new as required.
	Friction - damaged, worn	Inspect for damage. Install new as required.
	Cylinder Hub - damaged	Inspect for damage. Install new as required.
	Return Spring Assembly - damaged	Inspect for damage. Install new as required.

SHIFT CONCERNS: NO 5-4 SHIFT (AUTOMATIC)

Possible Component		Reference/Action
226 - ELECTRICAL ROUTINE
Powertrain Control System
	Electrical Inputs/Outputs, Vehicle Wiring Harnesses, PCM, Shift Solenoid A (SSA) Failed, Shift Solenoid B (SSB) Stuck On, Transmission Range (TR) Sensor	Run On-Board Diagnostic (OBD). Refer to Introduction - Gasoline Engines article for diagnosis. Go to Pinpoint Test A and Go to Pinpoint Test D .
326 - HYDRAULIC/MECHANICAL ROUTINE
Main Control Valve Body
	Bolts out of torque specification	Tighten bolts to specification.
	Gaskets and Separator Plate - damaged, off location	Inspect for damage. Install new as required.
	Direct Regulator and Boost Valves, Springs, Clips - loose, stuck, missing, misassembled, clutch failed on	Inspect for damage. Repair or install new as required.
	Forward Regulator and Boost Valves, Springs, Clips - loose, stuck, missing, misassembled, clutch failed off	Inspect for damage. Repair or install new as required.
	SSA not functioning correctly, SSB stuck on	Activate solenoid using scan tool. Refer to Output State Control (OSC) Mode . Go to Pinpoint Test A . Install a new solenoid body. Refer to Solenoid Body Assembly . Download a new solenoid body strategy into the PCM. Refer to Solenoid Body Strategy .
Direct Clutch Assembly - Failed On
	Seals - damaged	Inspect for damage. Install new as required.
	Piston - damaged	Inspect for damage. Install new as required.
	Friction - damaged, worn	Inspect for damage. Install new as required.
	Cylinder Hub - damaged	Inspect for damage. Install new as required.
	Return Spring Assembly - damaged	Inspect for damage. Install new as required.
Forward Clutch Assembly - Failed Off
	Seals - damaged	Inspect for damage. Install new as required.
	Piston - damaged	Inspect for damage. Install new as required.
	Friction - damaged, worn	Inspect for damage. Install new as required.
	Cylinder Hub - damaged	Inspect for damage. Install new as required.
	Return Spring Assembly - damaged	Inspect for damage. Install new as required.

SHIFT CONCERNS: NO 4-3 SHIFT (AUTOMATIC)

Possible Component		Reference/Action
227 - ELECTRICAL ROUTINE
Powertrain Control System
	Electrical Inputs/Outputs, Vehicle Wiring Harnesses, PCM, Shift Solenoid B (SSB) Failed, Shift Solenoid D (SSD) Stuck On, Transmission Range (TR) Sensor	Run On-Board Diagnostic (OBD). Refer to Introduction - Gasoline Engines article for diagnosis. Go to Pinpoint Test A and Go to Pinpoint Test D .
327 - HYDRAULIC/MECHANICAL ROUTINE
Main Control Valve Body
	Bolts out of torque specification	Tighten bolts to specification.
	Gaskets and Separator Plate - damaged, off location	Inspect for damage. Install new as required.
	Overdrive Regulator and Boost Valves, Springs, Clips - loose, stuck, missing, misassembled, clutch failed on	Inspect for damage. Repair or install new as required.
	Direct Regulator and Boost Valves, Springs, Clips - loose, stuck, missing, misassembled, clutch failed off	Inspect for damage. Repair or install new as required.
	SSB not functioning correctly, SSD stuck on	Activate solenoid using scan tool. Refer to Output State Control (OSC) Mode . Go to Pinpoint Test A . Install a new solenoid body. Refer to Solenoid Body Assembly . Download a new solenoid body strategy into the PCM. Refer to Solenoid Body Strategy .
Overdrive Clutch Assembly - Failed On
	Seals - damaged	Inspect for damage. Install new as required.
	Piston - damaged	Inspect for damage. Install new as required.
	Friction - damaged, worn	Inspect for damage. Install new as required.
	Cylinder Hub - damaged	Inspect for damage. Install new as required.
	Return Spring Assembly - damaged	Inspect for damage. Install new as required.
Direct Clutch Assembly - Failed Off
	Seals - damaged	Inspect for damage. Install new as required.
	Piston - damaged	Inspect for damage. Install new as required.
	Friction - damaged, worn	Inspect for damage. Install new as required.
	Cylinder Hub - damaged	Inspect for damage. Install new as required.
	Return Spring Assembly - damaged	Inspect for damage. Install new as required.

SHIFT CONCERNS: NO 3-2 SHIFT (AUTOMATIC)

Possible Component		Reference/Action
228 - ELECTRICAL ROUTINE
Powertrain Control System
	Electrical Inputs/Outputs, Vehicle Wiring Harnesses, PCM, Shift Solenoid C (SSC) Failed, Shift Solenoid B (SSB) Stuck On, Transmission Range (TR) Sensor	Run On-Board Diagnostic (OBD). Refer to Introduction - Gasoline Engines article for diagnosis. Go to Pinpoint Test A and Go to Pinpoint Test D .
328 - HYDRAULIC/MECHANICAL ROUTINE
Incorrect Pressures
	Line pressure	Check pressure at line pressure tap. Carry out Line Pressure Test. Refer to Special Testing Procedures . See the Line Pressure Chart for specifications. If not OK, check Main Control Valve Body.
Main Control Valve Body
	Bolts out of torque specification	Tighten bolts to specification.
	Gaskets and Separator Plate - damaged, off location	Inspect for damage. Install new as required.
	Direct Regulator and Boost Valves, Springs, Clips - loose, stuck, missing, misassembled, stuck on	Inspect for damage. Repair or install new as required.
	Intermediate Regulator and Boost Valves, Springs, Clips - loose, stuck, missing, misassembled, stuck off	Inspect for damage. Repair or install new as required.
	SSB or SSC not functioning correctly	Activate solenoid using scan tool. Refer to Output State Control (OSC) Mode . Go to Pinpoint Test A . Install a new solenoid body. Refer to Solenoid Body Assembly . Download a new solenoid body strategy into the PCM. Refer to Solenoid Body Strategy .
Direct Clutch Assembly - Failed On
	Seals - damaged	Inspect for damage. Install new as required.
	Piston - damaged	Inspect for damage. Install new as required.
	Friction - damaged, worn	Inspect for damage. Install new as required.
	Cylinder Hub - damaged	Inspect for damage. Install new as required.
	Return Spring Assembly - damaged	Inspect for damage. Install new as required.
Intermediate Clutch Assembly - Failed Off
	Seals - damaged	Inspect for damage. Install new as required.
	Piston - damaged	Inspect for damage. Install new as required.
	Friction - damaged, worn	Inspect for damage. Install new as required.
	Cylinder Hub - damaged	Inspect for damage. Install new as required.
	Return Spring Assembly - damaged	Inspect for damage. Install new as required.

SHIFT CONCERNS: NO 2-1 SHIFT (AUTOMATIC)

Possible Component		Reference/Action
229 - ELECTRICAL ROUTINE
Powertrain Control System
	Electrical Inputs/Outputs, Vehicle Wiring Harnesses, PCM, Shift Solenoid C (SSC) Stuck On, Transmission Range (TR) Sensor	Run On-Board Diagnostic (OBD). Refer to Introduction - Gasoline Engines article for diagnosis. Go to Pinpoint Test A and Go to Pinpoint Test D .
329 - HYDRAULIC/MECHANICAL ROUTINE
Incorrect Pressures
	Line pressure	Check pressure at line pressure tap. Carry out Line Pressure Test. Refer to Special Testing Procedures . See the Line Pressure Chart for specifications. If not OK, check Main Control Valve Body.
Main Control Valve Body
	Bolts out of torque specification	Tighten bolts to specification.
	Gaskets and Separator Plate - damaged, off location	Inspect for damage. Install new as required.
	Intermediate Regulator Valve, Springs, Clips - loose, stuck, missing, misassembled, stuck on	Inspect for damage. Repair or install new as required.
	SSC not functioning correctly, stuck on	Activate solenoid using scan tool. Refer to Output State Control (OSC) Mode . Go to Pinpoint Test A . Install a new solenoid body. Refer to Solenoid Body Assembly . Download a new solenoid body strategy into the PCM. Refer to Solenoid Body Strategy .
Intermediate Clutch Assembly - Failed On
	Seals - damaged	Inspect for damage. Install new as required.
	Piston - damaged	Inspect for damage. Install new as required.
	Friction - damaged, worn	Inspect for damage. Install new as required.
	Cylinder Hub - damaged	Inspect for damage. Install new as required.
	Return Spring Assembly - damaged	Inspect for damage. Install new as required.
Low One-Way Clutch Assembly
	Damaged - Not holding	Inspect for damage. Install new as required.
Planetary Carrier
	Damaged	Inspect for damage. Install new as required.

SHIFT CONCERNS: SOFT/SLIPPING 1-2 SHIFT (AUTOMATIC)

Possible Component		Reference/Action
230 - ELECTRICAL ROUTINE
Solenoid Body
	Incorrect solenoid body strategy data stored in the PCM	Verify solenoid body strategy data stored in the PCM, download new identification and strategy as necessary. Refer to Solenoid Body Strategy .
330 - HYDRAULIC/MECHANICAL ROUTINE
Incorrect Pressures
	Line pressure	Check pressure at line pressure tap. Carry out Line Pressure Test. Refer to Special Testing Procedures . See the Line Pressure Chart for specifications. If not OK, check Main Control Valve Body.
Main Control Valve Body
	Bolts out of torque specification	Tighten bolts to specification.
	Gaskets and Separator Plate - damaged, off location	Inspect for damage. Install new as required.
	Intermediate Regulator Valve, Springs, Clips - loose, stuck, missing, binding, misassembled	Inspect for damage. Repair or install new as required.
	Shift Solenoid C (SSC) not functioning correctly	Activate solenoid using scan tool. Refer to Output State Control (OSC) Mode . Go to Pinpoint Test A . Install a new solenoid body. Refer to Solenoid Body Assembly . Download a new solenoid body strategy into the PCM. Refer to Solenoid Body Strategy .
Intermediate Clutch Assembly
	Seals - damaged	Inspect for damage. Install new as required.
	Piston - damaged	Inspect for damage. Install new as required.
	Friction - damaged, worn	Inspect for damage. Install new as required.
	Cylinder Hub - damaged	Inspect for damage. Install new as required.
	Return Spring Assembly - damaged	Inspect for damage. Install new as required.
Pump Assembly
	Worn/cross leaks	Inspect for damage. Install new as required.
	Component damaged	Inspect for damage. Install a new pump assembly if required.

SHIFT CONCERNS: SOFT/SLIPPING 2-3 SHIFT (AUTOMATIC)

Possible Component		Reference/Action
231 - ELECTRICAL ROUTINE
Solenoid Body
	Incorrect solenoid body strategy data stored in the PCM	Verify solenoid body strategy data stored in the PCM, download new identification and strategy as necessary. Refer to Solenoid Body Strategy .
331 - HYDRAULIC/MECHANICAL ROUTINE
Incorrect Pressures
	Line pressure	Check pressure at line pressure tap. Carry out Line Pressure Test. Refer to Special Testing Procedures . See the Line Pressure Chart for specifications. If not OK, check Main Control. Refer to Main Control .
Main Control Valve Body
	Bolts out of torque specification	Tighten bolts to specification.
	Gaskets and Separator Plate - damaged, off location	Inspect for damage. Install new as required.
	Direct Regulator and Boost Valves, Springs, Clips - loose, stuck, binding, missing, misassembled	Inspect for damage. Repair or install new as required.
	Intermediate Regulator and Boost Valves, Springs, Clips - loose, stuck, binding, missing, misassembled	Inspect for damage. Repair or install new as required.
	Multiplex Valve, Springs, Clips - loose, stuck, missing, binding misassembled	Inspect for damage. Repair or install new as required.
	Shift Solenoid B (SSB) or Shift Solenoid C (SSC) not functioning correctly	Activate solenoid using scan tool. Refer to Output State Control (OSC) Mode . Go to Pinpoint Test A . Install a new solenoid body. Refer to Solenoid Body Assembly . Download a new solenoid body strategy into the PCM. Refer to Solenoid Body Strategy .
Direct Clutch Assembly
	Seals - damaged	Inspect for damage. Install new as required.
	Piston - damaged	Inspect for damage. Install new as required.
	Friction - damaged, worn	Inspect for damage. Install new as required.
	Cylinder Hub - damaged	Inspect for damage. Install new as required.
	Return Spring Assembly - damaged	Inspect for damage. Install new as required.
Intermediate Clutch Assembly
	Seals - damaged	Inspect for damage. Install new as required.
	Piston - damaged	Inspect for damage. Install new as required.
	Friction - damaged, worn	Inspect for damage. Install new as required.
	Cylinder Hub - damaged	Inspect for damage. Install new as required.
	Return Spring Assembly - damaged	Inspect for damage. Install new as required.

SHIFT CONCERNS: SOFT/SLIPPING 3-4 SHIFT (AUTOMATIC)

Possible Component		Reference/Action
232 - ELECTRICAL ROUTINE
Solenoid Body
	Incorrect solenoid body strategy data stored in the PCM	Verify solenoid body strategy data stored in the PCM, download new identification and strategy as necessary. Refer to Solenoid Body Strategy .
332 - HYDRAULIC/MECHANICAL ROUTINE
Main Control Valve Body
	Bolts out of torque specification	Tighten bolts to specification.
	Gaskets and Separator Plate - damaged, off location	Inspect for damage. Install new as required.
	Overdrive Regulator and Boost Valves, Springs, Clips - loose, stuck, binding, missing, misassembled	Inspect for damage. Repair or install new as required.
	Direct Regulator and Boost Valves, Springs, Clips - loose, stuck, binding, missing, misassembled	Inspect for damage. Repair or install new as required.
	Shift Solenoid D (SSD) or Shift Solenoid B (SSB) not functioning correctly	Activate solenoid using scan tool. Refer to Output State Control (OSC) Mode . Go to Pinpoint Test A . Install a new solenoid body. Refer to Solenoid Body Assembly . Download a new solenoid body strategy into the PCM. Refer to Solenoid Body Strategy .
Overdrive Clutch Assembly
	Seals - damaged	Inspect for damage. Install new as required.
	Piston - damaged	Inspect for damage. Install new as required.
	Friction - damaged, worn	Inspect for damage. Install new as required.
	Cylinder Hub - damaged	Inspect for damage. Install new as required.
	Return Spring Assembly - damaged	Inspect for damage. Install new as required.
Direct Clutch Assembly
	Seals - damaged	Inspect for damage. Install new as required.
	Piston - damaged	Inspect for damage. Install new as required.
	Friction - damaged, worn	Inspect for damage. Install new as required.
	Cylinder Hub - damaged	Inspect for damage. Install new as required.
	Return Spring Assembly - damaged	Inspect for damage. Install new as required.

SHIFT CONCERNS: SOFT/SLIPPING 4-5 SHIFT (AUTOMATIC)

Possible Component		Reference/Action
233 - ELECTRICAL ROUTINE
Solenoid Body
	Incorrect solenoid body strategy data stored in the PCM	Verify solenoid body strategy data stored in the PCM, download new identification and strategy as necessary. Refer to Solenoid Body Strategy .
333 - HYDRAULIC/MECHANICAL ROUTINE
Main Control Valve Body
	Bolts out of torque specification	Tighten bolts to specification.
	Gaskets and Separator Plate - damaged, off location	Inspect for damage. Install new as required.
	Direct Regulator and Boost Valves, Springs, Clips - loose, stuck, binding, missing, misassembled	Inspect for damage. Repair or install new as required.
	Forward Regulator and Boost Valves, Springs, Clips - loose, stuck, binding, missing, misassembled	Inspect for damage. Repair or install new as required.
	Shift Solenoid B (SSB) or Shift Solenoid A (SSA) not functioning correctly	Activate solenoid using scan tool. Refer to Output State Control (OSC) Mode . Go to Pinpoint Test A . Install a new solenoid body. Refer to Solenoid Body Assembly . Download a new solenoid body strategy into the PCM. Refer to Solenoid Body Strategy .
Direct Clutch Assembly
	Seals - damaged	Inspect for damage. Install new as required.
	Piston - damaged	Inspect for damage. Install new as required.
	Friction - damaged, worn	Inspect for damage. Install new as required.
	Cylinder Hub - damaged	Inspect for damage. Install new as required.
	Return Spring Assembly - damaged	Inspect for damage. Install new as required.
Forward Clutch Assembly
	Seals - damaged	Inspect for damage. Install new as required.
	Piston - damaged	Inspect for damage. Install new as required.
	Friction - damaged, worn	Inspect for damage. Install new as required.
	Cylinder Hub - damaged	Inspect for damage. Install new as required.
	Return Spring Assembly - damaged	Inspect for damage. Install new as required.

SHIFT CONCERNS: SOFT/SLIPPING 5-6 SHIFT (AUTOMATIC)

Possible Component		Reference/Action
234 - ELECTRICAL ROUTINE
Solenoid Body
	Incorrect solenoid body strategy data stored in the PCM	Verify solenoid body strategy data stored in the PCM, download new identification and strategy as necessary. Refer to Solenoid Body Strategy .
334 - HYDRAULIC/MECHANICAL ROUTINE
Main Control Valve Body
	Bolts out of torque specification	Tighten bolts to specification.
	Gaskets and Separator Plate - damaged, off location	Inspect for damage. Install new as required.
	Intermediate Regulator and Boost Valves, Springs, Clips - loose, stuck, binding, missing, misassembled	Inspect for damage. Repair or install new as required.
	Direct Regulator and Boost Valves, Springs, Clips - loose, stuck, binding, missing, misassembled	Inspect for damage. Repair or install new as required.
	Shift Solenoid C (SSC) or Shift Solenoid B (SSB) not functioning correctly	Activate solenoid using scan tool. Refer to Output State Control (OSC) Mode . Go to Pinpoint Test A . Install a new solenoid body. Refer to Solenoid Body Assembly . Download a new solenoid body strategy into the PCM. Refer to Solenoid Body Strategy .
Intermediate Clutch Assembly
	Seals - damaged	Inspect for damage. Install new as required.
	Piston - damaged	Inspect for damage. Install new as required.
	Friction - damaged, worn	Inspect for damage. Install new as required.
	Cylinder Hub - damaged	Inspect for damage. Install new as required.
	Return Spring Assembly - damaged	Inspect for damage. Install new as required.
Direct Clutch Assembly
	Seals - damaged	Inspect for damage. Install new as required.
	Piston - damaged	Inspect for damage. Install new as required.
	Friction - damaged, worn	Inspect for damage. Install new as required.
	Cylinder Hub - damaged	Inspect for damage. Install new as required.
	Return Spring Assembly - damaged	Inspect for damage. Install new as required.

SHIFT CONCERNS: SOFT/SLIPPING 6-5 SHIFT (AUTOMATIC)

Possible Component		Reference/Action
235 - ELECTRICAL ROUTINE
Solenoid Body
	Incorrect solenoid body strategy data stored in the PCM	Verify solenoid body strategy data stored in the PCM, download new identification and strategy as necessary. Refer to Solenoid Body Strategy .
335 - HYDRAULIC/MECHANICAL ROUTINE
Main Control Valve Body
	Bolts out of torque specification	Tighten bolts to specification.
	Gaskets and Separator Plate - damaged, off location	Inspect for damage. Install new as required.
	Intermediate Regulator and Boost Valves, Springs, Clips - loose, stuck, binding, missing, misassembled	Inspect for damage. Repair or install new as required.
	Direct Regulator and Boost Valves, Springs, Clips - loose, stuck, binding, missing, misassembled	Inspect for damage. Repair or install new as required.
	Shift Solenoid C (SSC) or Shift Solenoid B (SSB) not functioning correctly	Activate solenoid using scan tool. Refer to Output State Control (OSC) Mode . Go to Pinpoint Test A . Install a new solenoid body. Refer to Solenoid Body Assembly . Download a new solenoid body strategy into the PCM. Refer to Solenoid Body Strategy .
Intermediate Clutch Assembly
	Seals - damaged	Inspect for damage. Install new as required.
	Piston - damaged	Inspect for damage. Install new as required.
	Friction - damaged, worn	Inspect for damage. Install new as required.
	Cylinder Hub - damaged	Inspect for damage. Install new as required.
	Return Spring Assembly - damaged	Inspect for damage. Install new as required.
Direct Clutch Assembly
	Seals - damaged	Inspect for damage. Install new as required.
	Piston - damaged	Inspect for damage. Install new as required.
	Friction - damaged, worn	Inspect for damage. Install new as required.
	Cylinder Hub - damaged	Inspect for damage. Install new as required.
	Return Spring Assembly - damaged	Inspect for damage. Install new as required.

SHIFT CONCERNS: SOFT/SLIPPING 5-4 SHIFT (AUTOMATIC)

Possible Component		Reference/Action
236 - ELECTRICAL ROUTINE
Solenoid Body
	Incorrect solenoid body strategy data stored in the PCM	Verify solenoid body strategy data stored in the PCM, download new identification and strategy as necessary. Refer to Solenoid Body Strategy .
336 - HYDRAULIC/MECHANICAL ROUTINE
Main Control Valve Body
	Bolts out of torque specification	Tighten bolts to specification.
	Gaskets and Separator Plate - damaged, off location	Inspect for damage. Install new as required.
	Direct Regulator and Boost Valves, Springs, Clips - loose, stuck, missing, misassembled, clutch failed on	Inspect for damage. Repair or install new as required.
	Forward Regulator and Boost Valves, Springs, Clips - loose, stuck, missing, misassembled, clutch failed off	Inspect for damage. Repair or install new as required.
	Shift Solenoid A (SSA) not functioning correctly, Shift Solenoid B (SSB) stuck on	Activate solenoid using scan tool. Refer to Output State Control (OSC) Mode . Go to Pinpoint Test A . Install a new solenoid body. Refer to Solenoid Body Assembly . Download a new solenoid body strategy into the PCM. Refer to Solenoid Body Strategy .
Direct Clutch Assembly
	Seals - damaged	Inspect for damage. Install new as required.
	Piston - damaged	Inspect for damage. Install new as required.
	Friction - damaged, worn	Inspect for damage. Install new as required.
	Cylinder Hub - damaged	Inspect for damage. Install new as required.
	Return Spring Assembly - damaged	Inspect for damage. Install new as required.
Forward Clutch Assembly
	Seals - damaged	Inspect for damage. Install new as required.
	Piston - damaged	Inspect for damage. Install new as required.
	Friction - damaged, worn	Inspect for damage. Install new as required.
	Cylinder Hub - damaged	Inspect for damage. Install new as required.
	Return Spring Assembly - damaged	Inspect for damage. Install new as required.

SHIFT CONCERNS: SOFT/SLIPPING 4-3 SHIFT (AUTOMATIC)

Possible Component		Reference/Action
237 - ELECTRICAL ROUTINE
Solenoid Body
	Incorrect solenoid body strategy data stored in the PCM	Verify solenoid body strategy data stored in the PCM, download new identification and strategy as necessary. Refer to Solenoid Body Strategy .
337 - HYDRAULIC/MECHANICAL ROUTINE
Main Control Valve Body
	Bolts out of torque specification	Tighten bolts to specification.
	Gaskets and Separator Plate - damaged, off location	Inspect for damage. Install new as required.
	Overdrive Regulator and Boost Valves, Springs, Clips - loose, stuck, binding, missing, misassembled	Inspect for damage. Repair or install new as required.
	Direct Regulator and Boost Valves, Springs, Clips - loose, stuck, binding, missing, misassembled, clutch failed off	Inspect for damage. Repair or install new as required.
	Shift Solenoid B (SSB) or Shift Solenoid D (SSD) not functioning correctly	Activate solenoid using scan tool. Refer to Output State Control (OSC) Mode . Go to Pinpoint Test A . Install a new solenoid body. Refer to Solenoid Body Assembly . Download a new solenoid body strategy into the PCM. Refer to Solenoid Body Strategy .
Overdrive Clutch Assembly
	Seals - damaged	Inspect for damage. Install new as required.
	Piston - damaged	Inspect for damage. Install new as required.
	Friction - damaged, worn	Inspect for damage. Install new as required.
	Cylinder Hub - damaged	Inspect for damage. Install new as required.
	Return Spring Assembly - damaged	Inspect for damage. Install new as required.
Direct Clutch Assembly
	Seals - damaged	Inspect for damage. Install new as required.
	Piston - damaged	Inspect for damage. Install new as required.
	Friction - damaged, worn	Inspect for damage. Install new as required.
	Cylinder Hub - damaged	Inspect for damage. Install new as required.
	Return Spring Assembly - damaged	Inspect for damage. Install new as required.

SHIFT CONCERNS: SOFT/SLIPPING 3-2 SHIFT (AUTOMATIC)

Possible Component		Reference/Action
238 - ELECTRICAL ROUTINE
Solenoid Body
	Incorrect solenoid body strategy data stored in the PCM	Verify solenoid body strategy data stored in the PCM, download new identification and strategy as necessary. Refer to Solenoid Body Strategy .
338 - HYDRAULIC/MECHANICAL ROUTINE
Incorrect Pressures
	Line pressure	Check pressure at line pressure tap. Carry out Line Pressure Test. Refer to Special Testing Procedures . See the Line Pressure Chart for specifications. If not OK, check Main Control Valve Body.
Main Control Valve Body
	Bolts out of torque specification	Tighten bolts to specification.
	Gaskets and Separator Plate - damaged, off location	Inspect for damage. Install new as required.
	Direct Regulator and Boost Valves, Springs, Clips - loose, stuck, binding, missing, misassembled	Inspect for damage. Repair or install new as required.
	Intermediate Regulator and Boost Valves, Springs, Clips - loose, stuck, binding, missing, misassembled	Inspect for damage. Repair or install new as required.
	Multiplex Valve, Spring, Clip - loose, stuck, binding, missing, misassembled	Inspect for damage. Repair or install new as required.
	Shift Solenoid B (SSB) or Shift Solenoid C (SSC) not functioning correctly	Activate solenoid using scan tool. Refer to Output State Control (OSC) Mode . Go to Pinpoint Test A . Install a new solenoid body. Refer to Solenoid Body Assembly . Download a new solenoid body strategy into the PCM. Refer to Solenoid Body Strategy .
Direct Clutch Assembly
	Seals - damaged	Inspect for damage. Install new as required.
	Piston - damaged	Inspect for damage. Install new as required.
	Friction - damaged, worn	Inspect for damage. Install new as required.
	Cylinder Hub - damaged	Inspect for damage. Install new as required.
	Return Spring Assembly - damaged	Inspect for damage. Install new as required.
Intermediate Clutch Assembly
	Seals - damaged	Inspect for damage. Install new as required.
	Piston - damaged	Inspect for damage. Install new as required.
	Friction - damaged, worn	Inspect for damage. Install new as required.
	Cylinder Hub - damaged	Inspect for damage. Install new as required.
	Return Spring Assembly - damaged	Inspect for damage. Install new as required.

SHIFT CONCERNS: SOFT/SLIPPING 2-1 SHIFT (AUTOMATIC)

Possible Component		Reference/Action
239 - ELECTRICAL ROUTINE
Solenoid Body
	Incorrect solenoid body strategy data stored in the PCM	Verify solenoid body strategy data stored in the PCM, download new identification and strategy as necessary. Refer to Solenoid Body Strategy .
339 - HYDRAULIC/MECHANICAL ROUTINE
Incorrect Pressures
	Line pressure	Check pressure at line pressure tap. Carry out Line Pressure Test. Refer to Special Testing Procedures . See the Line Pressure Chart for specifications. If not OK, check Main Control Valve Body.
Main Control Valve Body
	Bolts out of torque specification	Tighten bolts to specification.
	Gaskets and Separator Plate - damaged, off location	Inspect for damage. Install new as required.
	Intermediate Regulator Valve, Springs, Clips - loose, stuck, binding, missing, misassembled	Inspect for damage. Repair or install new as required.
	Shift Solenoid C (SSC) not functioning correctly	Activate solenoid using scan tool. Refer to Output State Control (OSC) Mode . Go to Pinpoint Test A . Install a new solenoid body. Refer to Solenoid Body Assembly . Download a new solenoid body strategy into the PCM. Refer to Solenoid Body Strategy .
Intermediate Clutch Assembly
	Seals - damaged	Inspect for damage. Install new as required.
	Piston - damaged	Inspect for damage. Install new as required.
	Friction - damaged, worn	Inspect for damage. Install new as required.
	Cylinder Hub - damaged	Inspect for damage. Install new as required.
	Return Spring Assembly - damaged	Inspect for damage. Install new as required.
Low One-Way Clutch Assembly
	Damaged - not holding	Inspect for damage. Install new as required.
Planetary Carrier
	Damaged	Inspect for damage. Install new as required.

SHIFT CONCERNS: HARSH 1-2 SHIFT (AUTOMATIC)

Possible Component		Reference/Action
240 - ELECTRICAL ROUTINE
Solenoid Body
	Incorrect solenoid body strategy data stored in the PCM	Verify solenoid body strategy data stored in the PCM, download new identification and strategy as necessary. Refer to Solenoid Body Strategy .
340 - HYDRAULIC/MECHANICAL ROUTINE
Incorrect Pressures
	Line pressure	Check pressure at line pressure tap. Carry out Line Pressure Test. Refer to Special Testing Procedures . See the Line Pressure Chart for specifications. If not OK, check Main Control Valve Body.
Main Control Valve Body
	Bolts out of torque specification	Tighten bolts to specification.
	Gaskets and Separator Plate - damaged, off location	Inspect for damage. Install new as required.
	Intermediate Regulator Valve, Springs, Clips - loose, stuck, missing, binding, misassembled	Inspect for damage. Repair or install new as required.
	Shift Solenoid C (SSC) not functioning correctly	Activate solenoid using scan tool. Refer to Output State Control (OSC) Mode . Go to Pinpoint Test A . Install a new solenoid body. Refer to Solenoid Body Assembly . Download a new solenoid body strategy into the PCM. Refer to Solenoid Body Strategy .
Intermediate Clutch Assembly
	Seals - damaged	Inspect for damage. Install new as required.
	Piston - damaged	Inspect for damage. Install new as required.
	Friction - damaged, worn	Inspect for damage. Install new as required.
	Cylinder Hub - damaged	Inspect for damage. Install new as required.
	Return Spring Assembly - damaged	Inspect for damage. Install new as required.
Pump Assembly
	Worn/cross leaks	Inspect for damage. Install new as required.
	Component damaged	Inspect for damage, missing ball. Install a new pump assembly if required.

SHIFT CONCERNS: HARSH 2-3 SHIFT (AUTOMATIC)

Possible Component		Reference/Action
241 - ELECTRICAL ROUTINE
Solenoid Body
	Incorrect solenoid body strategy data stored in the PCM	Verify solenoid body strategy data stored in the PCM, download new identification and strategy as necessary. Refer to Solenoid Body Strategy .
341 - HYDRAULIC/MECHANICAL ROUTINE
Incorrect Pressures
	Line pressure	Check pressure at line pressure tap. Carry out Line Pressure Test. Refer to Special Testing Procedures . See the Line Pressure Chart for specifications. If not OK, check Main Control Valve Body.
Main Control Valve Body
	Bolts out of torque specification	Tighten bolts to specification.
	Gaskets and Separator Plate - damaged, off location	Inspect for damage. Install new as required.
	Direct Regulator and Boost Valves, Springs, Clips - loose, stuck, binding, missing, misassembled	Inspect for damage. Repair or install new as required.
	Intermediate Regulator and Boost Valves, Springs, Clips - loose, stuck, binding, missing, misassembled	Inspect for damage. Repair or install new as required.
	Multiplex Valve, Springs, Clips - loose, stuck, missing, binding misassembled	Inspect for damage. Repair or install new as required.
	Shift Solenoid B (SSB) or Shift Solenoid C (SSC) not functioning correctly	Activate solenoid using scan tool. Refer to Output State Control (OSC) Mode . Go to Pinpoint Test A . Install a new solenoid body. Refer to Solenoid Body Assembly . Download a new solenoid body strategy into the PCM. Refer to Solenoid Body Strategy .
Direct Clutch Assembly
	Seals - damaged	Inspect for damage. Install new as required.
	Piston - damaged	Inspect for damage. Install new as required.
	Friction - damaged, worn	Inspect for damage. Install new as required.
	Cylinder Hub - damaged	Inspect for damage. Install new as required.
	Return Spring Assembly - damaged	Inspect for damage. Install new as required.
Intermediate Clutch Assembly
	Seals - damaged	Inspect for damage. Install new as required.
	Piston - damaged	Inspect for damage. Install new as required.
	Friction - damaged, worn	Inspect for damage. Install new as required.
	Cylinder Hub - damaged	Inspect for damage. Install new as required.
	Return Spring Assembly - damaged	Inspect for damage. Install new as required.

SHIFT CONCERNS: HARSH 3-4 SHIFT (AUTOMATIC)

Possible Component		Reference/Action
242 - ELECTRICAL ROUTINE
Solenoid Body
	Incorrect solenoid body strategy data stored in the PCM	Verify solenoid body strategy data stored in the PCM, download new identification and strategy as necessary. Refer to Solenoid Body Strategy .
342 - HYDRAULIC/MECHANICAL ROUTINE
Main Control Valve Body
	Bolts out of torque specification	Tighten bolts to specification.
	Gaskets and Separator Plate - damaged, off location	Inspect for damage. Install new as required.
	Overdrive Regulator and Boost Valves, Springs, Clips - loose, stuck, binding, missing, misassembled	Inspect for damage. Repair or install new as required.
	Direct Regulator and Boost Valves, Springs, Clips - loose, stuck, binding, missing, misassembled	Inspect for damage. Repair or install new as required.
	Shift Solenoid D (SSD) or Shift Solenoid B (SSB) not functioning correctly	Activate solenoid using scan tool. Refer to Output State Control (OSC) Mode . Go to Pinpoint Test A . Install a new solenoid body. Refer to Solenoid Body Assembly . Download a new solenoid body strategy into the PCM. Refer to Solenoid Body Strategy .
Overdrive Clutch Assembly
	Seals - damaged	Inspect for damage. Install new as required.
	Piston - damaged	Inspect for damage. Install new as required.
	Friction - damaged, worn	Inspect for damage. Install new as required.
	Cylinder Hub - damaged	Inspect for damage. Install new as required.
	Return Spring Assembly - damaged	Inspect for damage. Install new as required.
Direct Clutch Assembly
	Seals - damaged	Inspect for damage. Install new as required.
	Piston - damaged	Inspect for damage. Install new as required.
	Friction - damaged, worn	Inspect for damage. Install new as required.
	Cylinder Hub - damaged	Inspect for damage. Install new as required.
	Return Spring Assembly - damaged	Inspect for damage. Install new as required.

SHIFT CONCERNS: HARSH 4-5 SHIFT (AUTOMATIC)

Possible Component		Reference/Action
243 - ELECTRICAL ROUTINE
Solenoid Body
	Incorrect solenoid body strategy data stored in the PCM	Verify solenoid body strategy data stored in the PCM, download new identification and strategy as necessary. Refer to Solenoid Body Strategy .
343 - HYDRAULIC/MECHANICAL ROUTINE
Main Control Valve Body
	Bolts out of torque specification	Tighten bolts to specification.
	Gaskets and Separator Plate - damaged, off location	Inspect for damage. Install new as required.
	Direct Regulator and Boost Valves, Springs, Clips - loose, stuck, binding, missing, misassembled	Inspect for damage. Repair or install new as required.
	Forward Regulator and Boost Valves, Springs, Clips - loose, stuck, binding, missing, misassembled	Inspect for damage. Repair or install new as required.
	Shift Solenoid B (SSB) or Shift Solenoid A (SSA) not functioning correctly	Activate solenoid using scan tool. Refer to Output State Control (OSC) Mode . Go to Pinpoint Test A . Install a new solenoid body. Refer to Solenoid Body Assembly . Download a new solenoid body strategy into the PCM. Refer to Solenoid Body Strategy .
Direct Clutch Assembly
	Seals - damaged	Inspect for damage. Install new as required.
	Piston - damaged	Inspect for damage. Install new as required.
	Friction - damaged, worn	Inspect for damage. Install new as required.
	Cylinder Hub - damaged	Inspect for damage. Install new as required.
	Return Spring Assembly - damaged	Inspect for damage. Install new as required.
Forward Clutch Assembly
	Seals - damaged	Inspect for damage. Install new as required.
	Piston - damaged	Inspect for damage. Install new as required.
	Friction - damaged, worn	Inspect for damage. Install new as required.
	Cylinder Hub - damaged	Inspect for damage. Install new as required.
	Return Spring Assembly - damaged	Inspect for damage. Install new as required.

SHIFT CONCERNS: HARSH 5-6 SHIFT (AUTOMATIC)

Possible Component		Reference/Action
244 - ELECTRICAL ROUTINE
Solenoid Body
	Incorrect solenoid body strategy data stored in the PCM	Verify solenoid body strategy data stored in the PCM, download new identification and strategy as necessary. Refer to Solenoid Body Strategy .
344 - HYDRAULIC/MECHANICAL ROUTINE
Main Control Valve Body
	Bolts out of torque specification	Tighten bolts to specification.
	Gaskets and Separator Plate - damaged, off location	Inspect for damage. Install new as required.
	Intermediate Regulator and Boost Valves, Springs, Clips - loose, stuck, binding, missing, misassembled	Inspect for damage. Repair or install new as required.
	Direct Regulator and Boost Valves, Springs, Clips - loose, stuck, binding, missing, misassembled	Inspect for damage. Repair or install new as required.
	Shift Solenoid C (SSC) or Shift Solenoid B (SSB) not functioning correctly	Activate solenoid using scan tool. Refer to Output State Control (OSC) Mode . Go to Pinpoint Test A . Install a new solenoid body. Refer to Solenoid Body Assembly . Download a new solenoid body strategy into the PCM. Refer to Solenoid Body Strategy .
Intermediate Clutch Assembly
	Seals - damaged	Inspect for damage. Install new as required.
	Piston - damaged	Inspect for damage. Install new as required.
	Friction - damaged, worn	Inspect for damage. Install new as required.
	Cylinder Hub - damaged	Inspect for damage. Install new as required.
	Return Spring Assembly - damaged	Inspect for damage. Install new as required.
Direct Clutch Assembly
	Seals - damaged	Inspect for damage. Install new as required.
	Piston - damaged	Inspect for damage. Install new as required.
	Friction - damaged, worn	Inspect for damage. Install new as required.
	Cylinder Hub - damaged	Inspect for damage. Install new as required.
	Return Spring Assembly - damaged	Inspect for damage. Install new as required.

SHIFT CONCERNS: HARSH 6-5 SHIFT (AUTOMATIC)

Possible Component		Reference/Action
245 - ELECTRICAL ROUTINE
Solenoid Body
	Incorrect solenoid body strategy data stored in the PCM	Verify solenoid body strategy data stored in the PCM, download new identification and strategy as necessary. Refer to Solenoid Body Strategy .
346 - HYDRAULIC/MECHANICAL ROUTINE
Main Control Valve Body
	Bolts out of torque specification	Tighten bolts to specification.
	Gaskets and Separator Plate - damaged, off location	Inspect for damage. Install new as required.
	Intermediate Regulator and Boost Valves, Springs, Clips - loose, stuck, binding, missing, misassembled	Inspect for damage. Repair or install new as required.
	Direct Regulator and Boost Valves, Springs, Clips - loose, stuck, binding, missing, misassembled	Inspect for damage. Repair or install new as required.
	Shift Solenoid C (SSC) or Shift Solenoid B (SSB) not functioning correctly	Activate solenoid using scan tool. Refer to Output State Control (OSC) Mode . Go to Pinpoint Test A . Install a new solenoid body. Refer to Solenoid Body Assembly . Download a new solenoid body strategy into the PCM. Refer to Solenoid Body Strategy .
Intermediate Clutch Assembly
	Seals - damaged	Inspect for damage. Install new as required.
	Piston - damaged	Inspect for damage. Install new as required.
	Friction - damaged, worn	Inspect for damage. Install new as required.
	Cylinder Hub - damaged	Inspect for damage. Install new as required.
	Return Spring Assembly - damaged	Inspect for damage. Install new as required.
Direct Clutch Assembly
	Seals - damaged	Inspect for damage. Install new as required.
	Piston - damaged	Inspect for damage. Install new as required.
	Friction - damaged, worn	Inspect for damage. Install new as required.
	Cylinder Hub - damaged	Inspect for damage. Install new as required.
	Return Spring Assembly - damaged	Inspect for damage. Install new as required.

SHIFT CONCERNS: HARSH 5-4 SHIFT (AUTOMATIC)

Possible Component		Reference/Action
246 - ELECTRICAL ROUTINE
Solenoid Body
	Incorrect solenoid body strategy data stored in the PCM	Verify solenoid body strategy data stored in the PCM, download new identification and strategy as necessary. Refer to Solenoid Body Strategy .
346 - HYDRAULIC/MECHANICAL ROUTINE
Main Control Valve Body
	Bolts out of torque specification	Tighten bolts to specification.
	Gaskets and Separator Plate - damaged, off location	Inspect for damage. Install new as required.
	Direct Regulator and Boost Valves, Springs, Clips - loose, stuck, missing, misassembled, clutch failed on	Inspect for damage. Repair or install new as required.
	Forward Regulator and Boost Valves, Springs, Clips - loose, stuck, missing, misassembled, clutch failed off	Inspect for damage. Repair or install new as required.
	Shift Solenoid A (SSA) not functioning correctly, Shift Solenoid B (SSB) stuck on	Activate solenoid using scan tool. Refer to Output State Control (OSC) Mode . Go to Pinpoint Test A . Install a new solenoid body. Refer to Solenoid Body Assembly . Download a new solenoid body strategy into the PCM. Refer to Solenoid Body Strategy .
Direct Clutch Assembly
	Seals - damaged	Inspect for damage. Install new as required.
	Piston - damaged	Inspect for damage. Install new as required.
	Friction - damaged, worn	Inspect for damage. Install new as required.
	Cylinder Hub - damaged	Inspect for damage. Install new as required.
	Return Spring Assembly - damaged	Inspect for damage. Install new as required.
Forward Clutch Assembly
	Seals - damaged	Inspect for damage. Install new as required.
	Piston - damaged	Inspect for damage. Install new as required.
	Friction - damaged, worn	Inspect for damage. Install new as required.
	Cylinder Hub - damaged	Inspect for damage. Install new as required.
	Return Spring Assembly - damaged	Inspect for damage. Install new as required.

SHIFT CONCERNS: HARSH 4-3 SHIFT (AUTOMATIC)

Possible Component		Reference/Action
247 - ELECTRICAL ROUTINE
Solenoid Body
	Incorrect solenoid body strategy data stored in the PCM	Verify solenoid body strategy data stored in the PCM, download new identification and strategy as necessary. Refer to Solenoid Body Strategy .
347 - HYDRAULIC/MECHANICAL ROUTINE
Main Control Valve Body
	Bolts out of torque specification	Tighten bolts to specification.
	Gaskets and Separator Plate - damaged, off location	Inspect for damage. Install new as required.
	Overdrive Regulator and Boost Valves, Springs, Clips - loose, stuck, binding, missing, misassembled	Inspect for damage. Repair or install new as required.
	Direct Regulator and Boost Valves, Springs, Clips - loose, stuck, binding, missing, misassembled, clutch failed off	Inspect for damage. Repair or install new as required.
	Shift Solenoid B (SSB) or Shift Solenoid D (SSD) not functioning correctly	Activate solenoid using scan tool. Refer to Output State Control (OSC) Mode . Go to Pinpoint Test A . Install a new solenoid body. Refer to Solenoid Body Assembly . Download a new solenoid body strategy into the PCM. Refer to Solenoid Body Strategy .
Overdrive Clutch Assembly
	Seals - damaged	Inspect for damage. Install new as required.
	Piston - damaged	Inspect for damage. Install new as required.
	Friction - damaged, worn	Inspect for damage. Install new as required.
	Cylinder Hub - damaged	Inspect for damage. Install new as required.
	Return Spring Assembly - damaged	Inspect for damage. Install new as required.
Direct Clutch Assembly
	Seals - damaged	Inspect for damage. Install new as required.
	Piston - damaged	Inspect for damage. Install new as required.
	Friction - damaged, worn	Inspect for damage. Install new as required.
	Cylinder Hub - damaged	Inspect for damage. Install new as required.
	Return Spring Assembly - damaged	Inspect for damage. Install new as required.

SHIFT CONCERNS: HARSH 3-2 SHIFT (AUTOMATIC)

Possible Component		Reference/Action
248 - ELECTRICAL ROUTINE
Solenoid Body
	Incorrect solenoid body strategy data stored in the PCM	Verify solenoid body strategy data stored in the PCM, download new identification and strategy as necessary. Refer to Solenoid Body Strategy .
348 - HYDRAULIC/MECHANICAL ROUTINE
Incorrect Pressures
	Line pressure	Check pressure at line pressure tap. Carry out Line Pressure Test. Refer to Special Testing Procedures . See the Line Pressure Chart for specifications. If not OK, check Main Control Valve Body.
Main Control Valve Body
	Bolts out of torque specification	Tighten bolts to specification.
	Gaskets and Separator Plate - damaged, off location	Inspect for damage. Install new as required.
	Direct Regulator and Boost Valves, Springs, Clips - loose, stuck, binding, missing, misassembled	Inspect for damage. Repair or install new as required.
	Intermediate Regulator and Boost Valves, Springs, Clips - loose, stuck, binding, missing, misassembled	Inspect for damage. Repair or install new as required.
	Shift Solenoid B (SSB) or Shift Solenoid C (SSC) not functioning correctly	Activate solenoid using scan tool. Refer to Output State Control (OSC) Mode . Go to Pinpoint Test A . Install a new solenoid body. Refer to Solenoid Body Assembly . Download a new solenoid body strategy into the PCM. Refer to Solenoid Body Strategy .
Direct Clutch Assembly
	Seals - damaged	Inspect for damage. Install new as required.
	Piston - damaged	Inspect for damage. Install new as required.
	Friction - damaged, worn	Inspect for damage. Install new as required.
	Cylinder Hub - damaged	Inspect for damage. Install new as required.
	Return Spring Assembly - damaged	Inspect for damage. Install new as required.
Intermediate Clutch Assembly
	Seals - damaged	Inspect for damage. Install new as required.
	Piston - damaged	Inspect for damage. Install new as required.
	Friction - damaged, worn	Inspect for damage. Install new as required.
	Cylinder Hub - damaged	Inspect for damage. Install new as required.
	Return Spring Assembly - damaged	Inspect for damage. Install new as required.

SHIFT CONCERNS: HARSH 2-1 SHIFT (AUTOMATIC)

Possible Component		Reference/Action
249 - ELECTRICAL ROUTINE
Solenoid Body
	Incorrect solenoid body strategy data stored in the PCM	Verify solenoid body strategy data stored in the PCM, download new identification and strategy as necessary. Refer to Solenoid Body Strategy .
349 - HYDRAULIC/MECHANICAL ROUTINE
Incorrect Pressures
	Line pressure	Check pressure at line pressure tap. Carry out Line Pressure Test. Refer to Special Testing Procedures . See the Line Pressure Chart for specifications. If not OK, check Main Control Valve Body.
Main Control Valve Body
	Bolts out of torque specification	Tighten bolts to specification.
	Gaskets and Separator Plate - damaged, off location	Inspect for damage. Install new as required.
	Intermediate Regulator Valve, Springs, Clips - loose, stuck, binding, missing, misassembled	Inspect for damage. Repair or install new as required.
	Shift Solenoid C (SSC) not functioning correctly	Activate solenoid using scan tool. Refer to Output State Control (OSC) Mode . Go to Pinpoint Test A . Install a new solenoid body. Refer to Solenoid Body Assembly . Download a new solenoid body strategy into the PCM. Refer to Solenoid Body Strategy .
Intermediate Clutch Assembly
	Seals - damaged	Inspect for damage. Install new as required.
	Piston - damaged	Inspect for damage. Install new as required.
	Friction - damaged, worn	Inspect for damage. Install new as required.
	Cylinder Hub - damaged	Inspect for damage. Install new as required.
	Return Spring Assembly - damaged	Inspect for damage. Install new as required.
Low One-Way Clutch Assembly
	Damaged - not holding	Inspect for damage. Install new as required.
Planetary Carrier
	Damaged	Inspect for damage. Install new as required.

TORQUE CONVERTER OPERATION CONCERNS: NO APPLY

Possible Component		Reference/Action
250 - ELECTRICAL ROUTINE
Powertrain Control System
	Electrical Inputs/Outputs, Vehicle Wiring Harnesses, PCM, Torque Converter Clutch (TCC) Solenoid, Throttle Position (TP), Transmission Fluid Temperature (TFT), Turbine Shaft Speed (TSS) and Output Shaft Speed (OSS) Sensor, Shorted Shift Solenoid	Carry out Torque Converter Operation Test. Refer to Torque Converter Diagnosis . Run On-Board Diagnostic (OBD). Refer to Introduction - Gasoline Engines article for diagnosis. Go to Pinpoint Test A , go to Pinpoint Test B and Go to Pinpoint Test C .
350 - HYDRAULIC/MECHANICAL ROUTINE
Incorrect Pressures
	Line pressure	Check pressure at line pressure tap. Carry out Line Pressure Test. Refer to Special Testing Procedures . See the Line Pressure Chart for specifications. If not OK, check Main Control Valve Body.
Main Control Valve Body
	Bolts out of torque specification	Tighten bolts to specification.
	Gaskets and Separator Plate - damaged, off location	Inspect for damage. Install new as required.
	TCC Regulator Valve, Springs, Clips - loose, stuck, missing, misassembled	Inspect for damage. Repair or install new as required.
	TCC Control Valve, Springs, Clips - loose, stuck, missing, misassembled	Inspect for damage. Repair or install new as required.
	TCC Solenoid - not functioning correctly	Activate solenoid using scan tool. Refer to Output State Control (OSC) Mode . Go to Pinpoint Test A . Install a new solenoid body. Refer to Solenoid Body Assembly . Download a new solenoid body strategy into the PCM. Refer to Solenoid Body Strategy .
Turbine Shaft
	Seals - damaged, missing	Inspect for damage. Repair as required.
	Holes - missing, plugged	Inspect for damage. Repair as required.
Stator Support Assembly
	Seals - damaged, missing	Inspect for damage. Repair as required.
	Holes - missing, plugged	Inspect for damage. Repair as required.
Torque Converter Hub Bushing
	Torque converter hub bushing worn	Inspect the bushing for damage and install a new torque converter as required.
	TCC worn	Install a new torque converter as required.

TORQUE CONVERTER OPERATION CONCERN: ALWAYS APPLIED/STALLS VEHICLE

Possible Component		Reference/Action
251 - ELECTRICAL ROUTINE
Powertrain Control System
	Electrical Inputs/Outputs, Vehicle Wiring Harnesses, PCM, Torque Converter Clutch (TCC) Solenoid	Carry out Torque Converter Operation Test. Refer to Torque Converter Diagnosis . Run On-Board Diagnostic (OBD). Refer to Introduction - Gasoline Engines article for diagnosis. Go to Pinpoint Test A using the scan tool. Repair as required. Clear codes. Road Test and rerun On-Board Diagnostic (OBD).
351 - HYDRAULIC/MECHANICAL ROUTINE
Main Controls
	Bolts out of torque specification	Tighten bolts to specification.
	Gaskets and Separator Plate - damaged, off location	Inspect gaskets. Repair as required.
	TCC Regulator Valve, Springs, Clips - loose, stuck, binding, missing, misassembled	Inspect for damage. Repair or install new as required.
	TCC Control Valve, Springs, Clips - loose, stuck, binding, missing, misassembled	Inspect for damage. Repair or install new as required.
	TCC Solenoid - not functioning correctly	Activate solenoid using scan tool. Refer to Output State Control (OSC) Mode . Go to Pinpoint Test A . Install a new solenoid body. Refer to Solenoid Body Assembly . Download a new solenoid body strategy into the PCM. Refer to Solenoid Body Strategy .

TORQUE CONVERTER OPERATION CONCERN: CYCLING/SHUDDER/CHATTER

Possible Component		Reference/Action
252 - ELECTRICAL ROUTINE
Powertrain Control System
	Electrical Inputs/Outputs, Vehicle Wiring Harnesses, PCM, Torque Converter Clutch (TCC) Solenoid	Carry out Torque Converter Operation Test. Refer to Torque Converter Diagnosis . Run On-Board Diagnostic (OBD). Refer to Introduction - Gasoline Engines article for diagnosis. Go to Pinpoint Test A using the scan tool. Repair as required. Clear codes. Road Test and rerun On-Board Diagnostic (OBD).
Solenoid Body
	Incorrect solenoid body strategy data stored in the PCM	Verify solenoid body strategy data stored in the PCM, download new identification and strategy as necessary. Refer to Solenoid Body Strategy .
352 - HYDRAULIC/MECHANICAL ROUTINE
	Transmission fluid condition	Prior to carrying out this action, make sure all electrical diagnostics have been carried out. Inspect transmission fluid condition. If burnt, drain transmission fluid and converter. Install new transmission fluid and transmission fluid filter assembly. Bring vehicle to normal operating temperature. Carry out Transaxle Drive Cycle Test. Carry out On-Board Diagnostic (OBD). If condition still exists, continue diagnostics.
Incorrect Pressures
	Line pressure	Check pressure at line pressure tap. Carry out Line Pressure Test. Refer to Special Testing Procedures . See the Line Pressure Chart for specifications. If not OK, check Main Control. Refer to Main Control .
Main Controls
	Bolts out of torque specification	Tighten bolts to specification.
	Gaskets and Separator Plate - damaged, off location	Inspect gaskets for damage. Repair as required.
	TCC Regulator Valve, Springs, Clips - loose, stuck, binding, missing, misassembled	Inspect for damage. Repair or install new as required.
	TCC Control Valve, Springs, Clips - loose, stuck, binding, missing, misassembled	Inspect for damage. Repair or install new as required.
	TCC Solenoid - not functioning correctly	Activate solenoid using scan tool. Refer to Output State Control (OSC) Mode . Go to Pinpoint Test A . Install a new solenoid body. Refer to Solenoid Body Assembly . Download a new solenoid body strategy into the PCM. Refer to Solenoid Body Strategy .
Turbine Shaft
	Seals - damaged, missing	Inspect for damage. Install new as required.
Torque Converter
	Torque converter damaged	Refer to Torque Converter .
Stator Support Assembly
	Stator support assembly - worn, damaged	Inspect for damage. Install new as required.
	Stator support seals - worn, damaged, leaking	Inspect for damage. Install new as required.

OTHER CONCERNS: NO ENGINE BRAKING IN MANUAL LOW POSITION

Possible Component		Reference/Action
260 - ELECTRICAL ROUTINE
	No Electrical Concerns
360 - HYDRAULIC/MECHANICAL ROUTINE
Main Control Valve Body
	Bolts out of torque specification	Tighten bolts to specification.
	Gaskets and Separator Plate - damaged, off location	Inspect for damage. Install new as required.
	Low/Reverse Regulator Valve, Springs, Clips - loose, stuck, binding, missing, misassembled	Inspect for damage. Repair or install new as required.
	Low/Reverse Boost Valve, Springs, Clips - loose, stuck, binding, missing, misassembled	Inspect for damage. Repair or install new as required.
	Shift Solenoid D (SSD) not functioning correctly	Activate solenoid using scan tool. Refer to Output State Control (OSC) Mode . Go to Pinpoint Test A . Install a new solenoid body. Refer to Solenoid Body Assembly . Download a new solenoid body strategy into the PCM. Refer to Solenoid Body Strategy .
Low/Reverse Clutch Assembly
	Seals - damaged	Inspect for damage. Install new as required.
	Piston - damaged	Inspect for damage. Install new as required.
	Friction - damaged, worn	Inspect for damage. Install new as required.
	Cylinder Hub - damaged	Inspect for damage. Install new as required.
	Return Spring Assembly - damaged	Inspect for damage. Install new as required.

OTHER CONCERNS: SELECTOR LEVER EFFORTS HIGH

Possible Component		Reference/Action
261 - ELECTRICAL ROUTINE
	No Electrical Concerns
361 - HYDRAULIC/MECHANICAL ROUTINE
Selector Lever Linkage (Internal, External)
	Damaged or out of adjustment	Inspect for damage. Repair as required. Verify selector lever adjustment. Refer to AUTOMATIC TRANSAXLE/TRANSMISSION EXTERNAL CONTROLS article.
Manual Control Lever
	External Retaining Pin - damaged, Nut - loose, Detent Spring - bent, damaged; or Park Mechanism - damaged, incorrect lever used	Inspect for damage. Repair or install new as required.
Main Control Valve Body
	Manual Valve - stuck	Inspect for damage. Repair or install new as required.
	Bolts out of torque specification	Tighten bolts to specification.
Brake Shift Interlock
	Mechanically damaged	Refer to AUTOMATIC TRANSAXLE/TRANSMISSION EXTERNAL CONTROLS article.
	Transmission Range (TR) sensor indicating park	Go to Pinpoint Test D .

OTHER CONCERNS: EXTERNAL LEAKS

Possible Component		Reference/Action
262 - ELECTRICAL ROUTINE
	No Electrical Concerns
362 - HYDRAULIC/MECHANICAL ROUTINE
Transmission Fluid Level
	High transmission fluid level	Check transmission fluid level and adjust as necessary. Refer to Preliminary Inspection .
	Transmission fluid condition	Carry out transmission fluid condition check. Refer to Preliminary Inspection .
Seals, Gaskets
	Leaks: Converter, Turbine Shaft Speed (TSS) Sensor, Halfshaft Axles, Gasket/Seal Manual Lever, Fluid Level Indicator, Main Control Cover, Incorrect Hub Seal	Locate source of leak. Repair as required.
Other
	Leaks: Cooler Fitting, Pressure Taps, Transaxle Connector, Transaxle Pan, Cooler Tubes, Case Porosity, Case Cracked	Locate source of leak. Repair as required.
	Vent - blocked damaged	Check vent for damage or blockage. Repair as required.

OTHER CONCERNS: POOR VEHICLE PERFORMANCE

Possible Component		Reference/Action
263 - ELECTRICAL ROUTINE
Powertrain Control System
	Electrical Inputs/Outputs, Vehicle Wiring Harnesses, PCM, Torque Converter Clutch (TCC) Solenoid, Throttle Position (TP), Output Shaft Speed (OSS), Mass Air Flow (MAF), Intake Air Temperature (IAT) Sensors, Internal Wiring Harness	Run On-Board Diagnostic (OBD). Refer to the Introduction - Gasoline Engines article for diagnosis. Go to Pinpoint Test C using scan tool. Repair as required. Clear codes. Road test and rerun On-Board Diagnostic (OBD).
		Carry out Shift Point Road Test. Refer to Shift Point Road Test . and carry out Torque Converter Operation Test. Refer to Torque Converter Diagnosis .
363 - HYDRAULIC/MECHANICAL ROUTINE
Transmission Fluid
	Low transmission fluid level	Check transmission fluid level and adjust as necessary. Refer to Preliminary Inspection .
Verify Correct Shift Scheduling, Engagements, Line Pressures and Stall Speed
		Go to the appropriate Diagnostic Routines per Index.
Converter Clutch Always Applied
		Go to Routine 351.

NOTE: NVH symptoms should be identified using the diagnostic tools that are available. For a list of these tools, an explanation of their uses and a glossary of common terms, refer to NOISE, VIBRATION AND HARSHNESS article. Since it is possible any one of multiple systems may be the cause of a symptom, it may be necessary to use a process of elimination type of diagnostic approach to pinpoint the responsible system. If this is not the causal system for the symptom, refer back to NOISE, VIBRATION AND HARSHNESS article for the next likely system and continue diagnosis.

OTHER CONCERNS: NOISE/VIBRATION - FORWARD OR REVERSE

Possible Component		Reference/Action
264 - ELECTRICAL ROUTINE
	No Electrical Concerns
364 - HYDRAULIC/MECHANICAL ROUTINE
For Noises/Vibrations That Change With Engine Speed
	Converter components	Locate source of disturbance. Repair as required.
		Transmission fluid level (low) - pump cavitation.
		Pump assembly.
	Engine Drive Accessories
	Transmission Fluid Cooler Tubes grounding out
	Flexplate
For Noises/Vibrations That Change With Vehicle Speed
	Engine Mounts - loose or damaged	Locate source of disturbance and repair as required.
	Driveline concerns: Halfshaft shudder CV joints Suspension Modifications
	Output/Halfshaft Splines - worn or damaged
	Turbine Shaft Speed (TSS) - incorrectly installed	Inspect for damage. Repair as required.
Other Noises/Vibrations
	Main Controls - Valve resonance	Locate source of disturbance and repair as required.
	Selector Lever Cable - vibration, grounding	Locate source of disturbance and repair as required.
	Transmission Fluid Cooler Tubes - grounding	Locate source of disturbance and repair as required.
	ABS	Refer to VEHICLE DYNAMIC SYSTEMS article.
	Power Steering Pump	Refer to POWER STEERING article.

OTHER CONCERNS: ENGINE WILL NOT CRANK

Possible Component		Reference/Action
265 - ELECTRICAL ROUTINE
Powertrain Control System
	Electrical Inputs/Outputs, Vehicle Wiring Harnesses, PCM, Transmission Range (TR) Sensor	Carry out Torque Converter Operation Test. Refer to Torque Converter Diagnosis . Run On-Board Diagnostic (OBD). Refer to the Introduction - Gasoline Engines article for diagnosis.
365 - HYDRAULIC/MECHANICAL ROUTINE
Selector Lever Linkage (Internal, External)
	Damaged or out of adjustment	Inspect for damage. Repair as required. Verify selector lever cable adjustment. Refer to AUTOMATIC TRANSAXLE/TRANSMISSION EXTERNAL CONTROLS article.

OTHER CONCERNS: NO PARK RANGE

Possible Component		Reference/Action
266 - ELECTRICAL ROUTINE
	No Electrical Concerns
366 - HYDRAULIC/MECHANICAL ROUTINE
Selector Lever Linkage (Internal/External)
	Damaged or out of adjustment	Inspect for damage. Repair as required. Verify selector lever cable adjustment. Refer to AUTOMATIC TRANSAXLE/TRANSMISSION EXTERNAL CONTROLS article.
Park Mechanism
	Park Brake Pawl, Parking Pawl Return Spring, Park Rod Abutment, Parking Pawl Shaft, Parking Pawl Actuating Rod, Manual Control Lever, Manual Lever Detent Spring - damaged	Inspect for damage. Repair as required.

OTHER CONCERNS: TRANSAXLE OVERHEATING

Possible Component		Reference/Action
267 - ELECTRICAL ROUTINE
	No Electrical Concerns
367 - HYDRAULIC/MECHANICAL ROUTINE
Transmission Fluid
	Incorrect transmission fluid level	Check transmission fluid level and adjust as necessary. Refer to Preliminary Inspection .
	Transmission fluid condition	Carry out transmission fluid condition check. Refer to Preliminary Inspection .
Transmission Fluid Cooler Tubes
	Damaged, blocked, reversed, leaking	Inspect for damage. Repair as required.
Auxiliary Cooler
	Damaged, blocked, restricted or incorrectly installed	Inspect for damage. Repair as required.
Vehicle Concerns Causing Engine Overheating
		Refer to ENGINE COOLING article.
Main Control Valve Body
	Torque Converter Regulator Valve/Spring - stuck, damaged	Inspect for damage. Repair as required.
	Torque Converter Control Valve/Spring - stuck, damaged	Inspect for damage. Repair as required.
Torque Converter Not Applying
	Seized Converter One-Way Clutch (OWC)	See Routine 250/350. Inspect for damage. Repair as required.
Excessive Towing Loads
		Check GVW.
Idle or Driveability Concern
		Refer to the Introduction - Gasoline Engines article.
Incorrect Clutch Application or Oil Pressure Control System
		Carry out line pressure tests. Refer to Special Testing Procedures and carry out shift point road test. Refer to Shift Point Road Test . Repair as required. See the Line Pressure Chart, and Clutch Application Chart for specifications. Repair as required.