LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2009 >> Flex Limited, FWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 1114 (Supplemental Inflatable Restraint System) >> Removal And Installation >> Passenger Air Bag Module - MKX >> Removal

Passenger Air Bag Module - MKX: Removal

WARNING: This page is about a different car, the 2007 Lincoln MKX and 2007 Ford Edge. However, it is still accessible from the selected car via links, so may be relevant.
WARNING: Always carry or place a live air bag module with the air bag and deployment door/trim cover/tear seam pointed away from the body. Do not set a live air bag module down with the deployment door/trim cover/tear seam face down. Failure to follow these instructions may result in serious personal injury in the event of an accidental deployment.
WARNING: Never probe the electrical connectors on air bag, safety canopy or side air curtain modules. Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.
WARNING: To reduce the risk of accidental deployment, do not use any memory saver devices. Failure to follow this instruction may result in serious personal injury or death.
NOTE: The air bag warning indicator illuminates when the restraints control module (RCM) fuse is removed and the ignition switch is ON. This is normal operation and does not indicate a supplemental restraint system (SRS) fault.
NOTE: The supplemental restraint system (SRS) must be fully operational and free of faults before releasing the vehicle to the customer.
NOTE: Repair is made by installing a new part only. If the new part does not correct the condition, install the original part and carry out the diagnostic procedure again.
  1. Depower the SRS. For additional information, refer to Supplemental Restraint System (SRS) Depowering and Repowering .
  2. Open and lower the glove compartment door. Then unhook the glove compartment door from the instrument panel (I/P).
    • If equipped, detach the glove compartment door dampener.
  3. Pull straight out to release the 5 retaining clips and remove the RH instrument panel (I/P) finish panel.
  4. Remove the screw from the LH duct assembly bracket from the front of the I/P.
    5. Fig 1: Locating Screw On LH Duct Assembly Bracket
    GF0031220Courtesy of FORD MOTOR CO.
  5. Through the glove compartment opening, remove the screw and the LH duct assembly.
    6. Fig 2: Locating Screw On LH Duct Assembly
    GF0031221Courtesy of FORD MOTOR CO.
  6. Through the glove compartment opening, remove the screw and the RH duct assembly.
    7. Fig 3: Locating Screw On RH Duct Assembly
    GF0031222Courtesy of FORD MOTOR CO.
  7. Remove the 4 bolts and the passenger air bag module support bracket.
  8. Remove the 3 nuts from the passenger air bag module.
    9. CAUTION: Do not allow the passenger air bag module to hang from the wiring harness. Damage to the wiring harness and connectors may occur.
  9. Lower the rear of the passenger air bag module off the 3 mounting studs. Move the passenger air bag module rearward to release the 7 hooks from the I/P and rest the module on the cross vehicle beam.
    10. Fig 4: Identifying Hooks On I/P
    GF0031225Courtesy of FORD MOTOR CO.
  10. Using a small screwdriver as shown, lift up and release the locking button on the LH passenger air bag module electrical connector.
    11. Fig 5: Releasing Locking Button On LH Passenger Air Bag Module Electrical Connector Using A Small Screwdriver
    GF0031226Courtesy of FORD MOTOR CO.
    CAUTION: Do not pull the passenger air bag module electrical connector out by the locking button. Damage to the locking button may occur.
  11. With the LH locking button released, remove the LH electrical connector from the passenger air bag module.
  12. Using a small screwdriver as shown, lift up and release the locking button on the RH passenger air bag module electrical connector.
    13. Fig 6: Releasing Locking Button On RH Passenger Air Bag Module Electrical Connector Using A Small Screwdriver
    GF0031227Courtesy of FORD MOTOR CO.
    CAUTION: Do not pull the passenger air bag module electrical connector out by the locking button. Damage to the locking button may occur.
  13. With the RH locking button released, remove the RH electrical connector. Remove the passenger air bag module from the glove compartment opening.
scientia non olet · About LEMON Manuals