LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2009 >> Flex Limited, FWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 1114 (Supplemental Inflatable Restraint System) >> Diagnostic Tests >> Air Bag and Safety Belt Pretensioner Supplemental Restraint System (SRS) >> Pinpoint Test - Air Bag and Safety Belt Pretensioner Supplemental Restraint System (SRS) >> Pinpoint Test H: DTC B2293 - Restraint System - Air Bag Fault >> Normal Operation

Normal Operation

WARNING: This page is about a different car, the 2007 Lincoln MKX and 2007 Ford Edge. However, it is still accessible from the selected car via links, so may be relevant.

The restraints control module (RCM) monitors all front air bag module circuits for faults. The RCM will set a diagnostic trouble code (DTC) if a short to battery or short to ground fault is detected. The RCM will also set a DTC if the loop resistance is less than 0.9 ohm or greater than 5 ohms. The normal expected resistance range of driver air bag loop 1 and loop 2 is 1.47 to 4.26 ohms and 1.23 to 3.31 ohms for the passenger air bag loop 1 and loop 2. If a driver air bag loop resistance is between 0.9 and 1.47 or between 4.26 and 5 ohms and a passenger air bag loop resistance is between 0.9 and 1.23 or between 3.31 and 5 ohms, a DTC will not set but there exists a strong potential for an intermittent fault. If the RCM detects a fault on any of the front air bag circuits, it will store DTC B2293 in memory and send a message to the instrument cluster module to illuminate the air bag warning indicator.

Fault PIDsa Description Fault Trigger Condition
2293_16_OD and 2293_16_CM Air Bag Inflator Circuit Resistance Low - Loop No. 2, Front Passenger Side When the RCM measures resistance less than 0.9 ohm between the passenger air bag loop circuits, a fault will be indicated.
2293_17_OD and 2293_17_CM Air Bag Circuit Open - Loop No. 2, Front Passenger Side When the RCM measures resistance greater than 5 ohms between the passenger air bag loop circuits, a fault will be indicated.
2293_18_OD and 2293_18_CM Air Bag Circuit Short to Battery - Loop No. 2, Front Passenger Side When the RCM senses a short to voltage on either on the passenger air bag loop circuits, a fault will be indicated.
2293_19_OD and 2293_19_CM Air Bag Circuit Short to Ground - Loop No. 2, Front Passenger Side When the RCM senses a short to ground on either on the passenger air bag loop circuits, a fault will be indicated.
2293_20_OD and 2293_20_CM Air Bag Inflator Circuit Resistance Low - Loop No. 2, Front Driver Side When the RCM measures resistance less than 0.9 ohm between the driver air bag loop circuits, a fault will be indicated.
2293_21_OD and 2293_21_CM Air Bag Circuit Open - Loop No. 2, Front Driver Side When the RCM measures resistance greater than 5 ohms between the driver air bag loop circuits, a fault will be indicated.
2293_22_OD and 2293_22_CM Air Bag Circuit Short to Battery - Loop No. 2, Front Driver Side When the RCM senses a short to voltage on either on the driver air bag loop circuits, a fault will be indicated.
2293_23_OD and 2293_23_CM Air Bag Circuit Short to Ground - Loop No. 2, Front Driver Side When the RCM senses a short to ground on either on the driver air bag loop circuits, a fault will be indicated.
2293_24_OD and 2293_24_CM Air Bag Inflator Circuit Resistance Low - Loop No. 1, Front Passenger Side When the RCM measures resistance less than 0.9 ohm between the passenger air bag loop circuits, a fault will be indicated.
2293_25_OD and 2293_25_CM Air Bag Circuit Open - Loop No. 1, Front Passenger Side When the RCM measures resistance greater than 5 ohms between the passenger air bag loop circuits, a fault will be indicated.
2293_26_OD and 2293_26_CM Air Bag Circuit Short to Battery - Loop No. 1, Front Passenger Side When the RCM senses a short to voltage on either on the passenger air bag loop circuits, a fault will be indicated.
2293_27_OD and 2293_27_CM Air Bag Circuit Short to Ground - Loop No. 1, Front Passenger Side When the RCM senses a short to ground on either on the passenger air bag loop circuits, a fault will be indicated.
2293_28_OD and 2293_28_CM Air Bag Inflator Circuit Resistance Low - Loop No. 1, Front Driver Side When the RCM measures resistance less than 0.9 ohm between the driver air bag loop circuits, a fault will be indicated.
2293_29_OD and 2293_29_CM Air Bag Circuit Open - Loop No. 1, Front Driver Side When the RCM measures resistance greater than 5 ohms between the driver air bag loop circuits, a fault will be indicated.
2293_30_OD and 2293_30_CM Air Bag Circuit Short to Battery - Loop No. 1, Front Driver Side When the RCM senses a short to voltage on either on the driver air bag loop circuits, a fault will be indicated.
2293_31_OD and 2293_31_CM Air Bag Circuit Short to Ground - Loop No. 1, Front Driver Side When the RCM senses a short to ground on either on the driver air bag loop circuits, a fault will be indicated.

a Fault PIDs that end in OD indicate an on-demand status and are associated with on-demand DTC B2293. Fault PIDs that end in CM indicate continuous monitor status and are associated with continuous DTC B2293.

This pinpoint test is intended to diagnose the following:

scientia non olet · About LEMON Manuals