LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2009 >> Flex Limited, FWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 1073 (Rear Drive HALFSHAFTS) >> Removal And Installation >> Constant Velocity (CV) Joint Boot >> Assembly

Constant Velocity (CV) Joint Boot: Assembly

WARNING: This page is about a different car, the 2007 Lincoln MKX and 2007 Ford Edge. However, it is still accessible from the selected car via links, so may be relevant.
  1. For the outboard CV joint, carry out the following:
    1. Slide the boot on the interconnecting shaft.
    2. Pack the outboard CV joint with 80 g (2.82 oz.) of grease supplied in the boot kit.
    3. Spread any remaining grease evenly inside the boot.
    4. Install the boot by seating it in the groove in the CV joint housing.
    2. Fig 1: Identifying CV Joint Housing
    GF0027259Courtesy of FORD MOTOR CO.
  2. Using the special tool, install the 79.6 mm (3.13 in) boot clamps on the large end of the boot.
    3. Fig 2: Installing 79.6 mm (3.13 in) Boot Clamps On Large End Of Boot Using Special Tool (205-343)
    GF0027260Courtesy of FORD MOTOR CO.
  3. Install the small clamp on the small end of the boot.
    4. CAUTION: Install a new circlip every time the halfshaft is removed from the axle or damage to the component may occur.
    CAUTION: Start one end of the circlip in the groove and work the circlip over the halfshaft and into the groove to prevent the circlip from overexpanding or damage to the clamp may occur.
  4. Install a new retainer circlip.
    5. Fig 3: Locating Halfshaft Circlip
    G03972275Courtesy of FORD MOTOR CO.
  5. Position the small clamp on the interconnecting shaft before installing the boot.
  6. Position the boot on the interconnecting shaft.
  7. Install the inner race and the retainer snap ring.
    8. Fig 4: Locating Retainer Snap Ring
    GF0031527Courtesy of FORD MOTOR CO.
  8. Install the outer race with 8 balls.
    9. Fig 5: Locating Outer Race Balls
    GF0031526Courtesy of FORD MOTOR CO.
  9. Insert the assembly in the housing.
  10. Install the retaining ring.
    11. Fig 6: Locating Retaining Ring
    GF0031525Courtesy of FORD MOTOR CO.
  11. For the inboard CV joint, carry out the following:
    1. Pack the inboard CV joint housing with 108 g (3.80 oz.) of grease supplied in the boot kit.
    2. Spread any remaining grease evenly inside the boot and CV joint.
    3. Install the inboard CV joint housing, seating the boot in the groove in the housing.
  12. Set the halfshaft assembled length to specifications. For additional information, refer to SPECIFICATIONS .
    1. Measure the entire assembly length.
    2. Push in or pull out on the inner joint as necessary to adjust the halfshaft assembled length.
    3. Hold the inner joint to prevent the assembled length from changing and insert a soft, flat tool between the boot and the joint to equalize the pressure.
    13. Fig 7: Pushing In Or Pulling Out On Inner Joint As Necessary To Adjust Halfshaft Assembled Length
    GF0031528Courtesy of FORD MOTOR CO.
  13. Using the special tool, install the 77.5 mm (3.05 in) boot clamps on the large end of the boot.
    14. Fig 8: Installing 77.5 mm (3.05 in) Boot Clamps On Large End Of Boot Using Special Tool (205-343)
    GF0027267Courtesy of FORD MOTOR CO.
  14. Install the smaller boot clamp.
  15. Install the halfshaft assembly. For additional information, refer to Halfshaft .
scientia non olet · About LEMON Manuals