LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2007 >> Freestar SEL >> Repair and Diagnosis (Single Page) >> Accessories & Equipment >> Headlights >> Exterior Lighting System >> Diagnostic Tests >> Stoplamps >> Inspection and Verification

Inspection and Verification

  1. Verify the customer concern.
  2. Visually inspect the following for obvious signs of mechanical or electrical damage.
    VISUAL INSPECTION CHART

    Mechanical Electrical
    • Stoplamp switch
    • Bussed electrical center (BEC) fuse(s):
      • 58 (30A)
      • 65 (30A)
    • Smart junction box (SJB) fuse 15 (10A) (stoplamp switch)
    • Circuitry
    • SJB
    • Bulbs
  3. If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceeding to the next step.
    4. NOTE: Make sure the headlamp switch is in the OFF position.
    NOTE: Make sure the multifunction switch is in the LOW BEAM position.
    NOTE: Make sure to use the latest scan tool software release.
  4. If the cause is not visually evident, connect the scan tool to the data link connector (DLC).
    5. NOTE: The vehicle communication module (VCM) LED prove-out confirms power and ground from the DLC are provided to the VCM.
  5. If the scan tool does not communicate with the VCM:
    • Check the VCM connection to the vehicle.
    • Check the scan tool connection to the VCM.
    • Refer to MODULE COMMUNICATIONS NETWORK article, No Power To The Scan Tool, to diagnose no communication with the scan tool.
  6. If the scan tool does not communicate with the vehicle:
    • Verify the ignition key is in the ON position.
    • Verify the scan tool operation with a known good vehicle.
    • Refer to MODULE COMMUNICATIONS NETWORK article to diagnose no response from the powertrain control module (PCM).
  7. Carry out the network test.
    • If the scan tool responds with no communication for one or more modules, refer to MODULE COMMUNICATIONS NETWORK article.
    • If the network test passes, retrieve and record the continuous memory diagnostic trouble codes (DTCs).
  8. Clear the continuous DTCs and carry out the self-test diagnostics for the SJB.
  9. If the DTCs retrieved are related to the concern, go to the Smart Junction Box (SJB) Diagnostic Trouble Code (DTC) Index. For all other DTCs, refer to MULTIFUNCTION ELECTRONIC MODULES article.
  10. If no DTCs related to the concern are retrieved, go to Symptom Chart .
SMART JUNCTION BOX (SJB) DIAGNOSTIC TROUBLE CODE (DTC) INDEX

DTC Description Action
B1342 ECU is Defective CLEAR the DTCs. RETRIEVE the DTCs. If DTC B1342 is retrieved, INSTALL a new SJB. REFER to MULTIFUNCTION ELECTRONIC MODULES article. TEST the system for normal operation.
B1485 Brake Pedal Input Circuit Short to Battery Go to Pinpoint Test H .
B2044 Left Rear Stoplamp Circuit Short to Ground Go to Pinpoint Test G .
B2045 Left Rear Stoplamp Circuit Open Go to Pinpoint Test G .
B2046 Right Rear Stoplamp Circuit Short to Ground Go to Pinpoint Test G .
B2047 Right Rear Stoplamp Circuit Open Go to Pinpoint Test G .
B2519 High Mount Stoplamp Circuit Failure If the high mounted stoplamp is inoperative, go to Pinpoint Test G .
If the high mounted stoplamp is always on, go to Pinpoint Test H .
B2528 Left Rear Stoplamp Circuit Short to Battery Go to Pinpoint Test H .
B2534 Right Rear Stoplamp Circuit Short to Battery Go to Pinpoint Test H .
All other DTCs - REFER to MULTIFUNCTION ELECTRONIC MODULES article.
scientia non olet · About LEMON Manuals