Removal and Installation

WARNING: This page is about a different car, the 2005 Ford Pickup, 2005 Ford F550 Super Duty, 2005 Ford F450 Super Duty, and 2005 Ford Cab & Chassis. However, it is still accessible from the selected car via links, so may be relevant.

All vehicles

Remove the overhead console bezel.
- Release the locking tabs while pulling down.
  
  Fig 1: Releasing Locking Tabs
  Courtesy of FORD MOTOR CO.
Remove the screws and the left and right visors.
- If equipped, disconnect the electrical connector.
  
  Fig 2: Locating Visor Removing Screws
  Courtesy of FORD MOTOR CO.
Position the left and right front door opening weatherstripping down from the headliner.

Fig 3: Positioning Front Door Opening Weatherstripping Down
Courtesy of FORD MOTOR CO.
Remove the left and right windshield side garnish moulding. For additional information, refer to INTERIOR TRIM AND ORNAMENTATION .

NOTE: SuperCab shown, Regular Cab and Crew Cabs are similar.

NOTE: Crew Cab vehicles are equipped with two courtesy lamps.

Remove the courtesy lamp(s).
- Remove the courtesy lamp lens, then remove the screws.
  
  Fig 4: Removing Courtesy Lamp
  Courtesy of FORD MOTOR CO.

NOTE: Regular Cab shown.

Fig 5: Removing Scuff Plate

Courtesy of FORD MOTOR CO.

Remove the scuff plate(s).

SuperCab vehicles

Remove the left and right rear door striker covers at the roof trim panel.

Fig 6: Removing Rear Door Striker Covers At Roof Trim Panel
Courtesy of FORD MOTOR CO.
If equipped, remove the safety belt shoulder height adjuster cover pin-type retainers.

Fig 7: Locating Safety Belt Shoulder Height Adjuster Cover Pin-Type Retainers
Courtesy of FORD MOTOR CO.
If equipped, remove the safety belt shoulder height adjusters.
1. Position the safety belt shoulder height adjuster cover down.
2. Remove the bolt.
3. Remove the safety belt shoulder height adjuster.
  
  Fig 8: Removing Safety Belt Shoulder Height Adjusters
  Courtesy of FORD MOTOR CO.

Crew Cab vehicles

Remove the rear B-pillar assist handles.
1. Remove the four covers (two on each handle).
2. Remove the four screws (two on each handle).
3. Remove the two B-pillar assist handles.
  
  Fig 9: Removing Rear B-Pillar Assist Handles
  Courtesy of FORD MOTOR CO.

CAUTION: If the safety belt retractor is to be reused, do not allow the safety belt to be retracted all the way into the retractor. Doing so may cause the retractor to lock and not release the safety belt.

NOTE: Inspect the shoulder safety belt guide and cover for damage. If the shoulder safety belt guide or cover is damaged or cover does not remain closed, install a new shoulder safety belt guide.

Fig 10: Seat Nut -- With Torque Specifications

Courtesy of FORD MOTOR CO.

Lift up on the cover and remove the front and rear seat nut and shoulder safety belt guides.
Position the B-pillar trim panels aside.

Fig 11: Positioning B-Pillar Trim Panels Aside
Courtesy of FORD MOTOR CO.

All vehicles

Remove the two headliner rear pin-type retainers.

Fig 12: Identifying Two Headliner Rear Pin-Type Retainers
Courtesy of FORD MOTOR CO.
Remove the LH and RH shoulder safety belt guides.
1. Position the shoulder safety belt guide cover up.
2. Remove the shoulder safety belt guide nut.
3. Remove the shoulder safety belt guide.
  
  Fig 13: Removing Shoulder Safety Belt Guides - With Torque Specifications
  Courtesy of FORD MOTOR CO.
Position the LH and RH rear corner trim panels aside.

Fig 14: Positioning Rear Corner Trim Panels Aside
Courtesy of FORD MOTOR CO.
If equipped, remove the assist handle(s).
1. Remove the covers and bolts.
2. Remove the assist handle.
  
  Fig 15: Removing Assist Handle
  Courtesy of FORD MOTOR CO.

NOTE: Typical is shown.

Fig 16: Identifying Two Coat Hooks

Courtesy of FORD MOTOR CO.

Remove the two coat hooks.
Remove the two headliner front pin-type retainers and position the headliner aside.

Fig 17: Positioning Headliner Aside
Courtesy of FORD MOTOR CO.

NOTE: Pull down at the front of the bracket first.

Remove the overhead console bracket.
- Disconnect the electrical connector.
  
  Fig 18: Locating Electrical Connector
  Courtesy of FORD MOTOR CO.
To install, reverse the removal procedure.