Inspection and Verification
WARNING: This page is about a different car, the 2006 Mercury Mariner and 2006 Ford Escape. However, it is still accessible from the selected car via links, so may be relevant.
- Verify the customer concern.
- Inspect for obvious signs of mechanical or electrical damage.VISUAL INSPECTION CHART
Mechanical Electrical - Active torque coupling
- Transfer case
- Halfshafts and constant velocity (CV) joints
- Driveshaft and universal joints
- Fluid leaks
- Wheel/tire size and brand
- Matching tire size and brand
- Tire pressure
- Smart junction box (SJB) fuse(s):
- 18 (10A)
- 35 (5A)
- Four-wheel drive (4WD) control module
- Wiring harness
- Connector(s)
- Circuitry
- If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceeding to the next step.
- If the cause is not visually evident, connect the diagnostic tool to the data link connector and select the vehicle to be tested from the diagnostic tool menu. If the diagnostic tool does not communicate with the vehicle:
- check that the program card is correctly installed.
- check the connections to the vehicle.
- check the ignition switch position.
- If the diagnostic tool still does not communicate with the vehicle, refer to the diagnostic tool operating manual
- Carry out the diagnostic tool data link test. If the diagnostic tool responds with:
- CAN circuit fault; all electronic control units no response/not equipped, refer to MODULE COMMUNICATIONS NETWORK .
- No response/not equipped for 4WD control module, GO to PINPOINT TEST B .
- System passed, retrieve and record the continuous diagnostic trouble codes (DTCs), erase the continuous DTCs, and carry out the self-test diagnostics for the 4WD control module.
- If the DTCs retrieved are related to the concern, go to the FOUR-WHEEL DRIVE (4WD) CONTROL MODULE DIAGNOSTIC TROUBLE CODE (DTC) INDEX .
- If no DTCs related to the concern are retrieved, carry out the Functional Test, and GO to PINPOINT TEST A .
FOUR-WHEEL DRIVE (4WD) CONTROL MODULE DIAGNOSTIC TROUBLE CODE (DTC) INDEX
| DTC | Description | Possible Causes | Source | Action |
|---|---|---|---|---|
| B1317 | Battery Voltage High |
|
4WD Control Module | GO to PINPOINT TEST C . |
| B1318 | Battery Voltage Low |
|
4WD Control Module | GO to PINPOINT TEST C . |
| B1342 | ECU is Defective |
|
4WD Control Module | CLEAR the DTCs. REPEAT the self-test. If DTC B1342 is retrieved again, INSTALL a new 4WD control module. REFER to FOUR WHEEL DRIVE (4WD) CONTROL MODULE in this article. |
| P1635 | Tire/Axle Out of Acceptable Range |
|
4WD Control Module | GO to PINPOINT TEST J . |
| P1824 | 4WD Clutch Relay Circuit Failure |
|
4WD Control Module | CHECK SJB fuse 18 (10A). If the fuse is good, GO to PINPOINT TEST G . |
| P1825 | 4WD Clutch Relay Open Circuit |
|
4WD Control Module | CHECK SJB fuse 18 (10A). If the fuse is good, GO to PINPOINT TEST G . |
| U0100 | Lost Communication with PCM |
|
4WD Control Module | GO to PINPOINT TEST F . |
| U0121 | Lost Communication with Anti-lock Brake System (ABS) |
|
4WD Control Module | GO to PINPOINT TEST F . |
| U0401 | Invalid Data Received From PCM |
|
4WD Control Module | GO to PINPOINT TEST D . |
| U0415 | Invalid Data Received From ABS |
|
4WD Control Module | GO to PINPOINT TEST E . |
| U1900 | CAN Communication Bus Fault |
|
4WD Control Module | GO to PINPOINT TEST F . |