LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2006 >> Focus ZX5 SE, Standard >> Repair and Diagnosis >> External Pages >> Different car >> Section 168 (Handles, Locks, Latches And Entry Systems) >> Diagnosis And Testing >> Locks, Latches and Entry Systems >> Pinpoint Tests >> Pinpoint Test I: The Luggage Compartment Lid Is Inoperative Using The Remote Keyless Entry (RKE) Transmitter >> Testing

Pinpoint Test I: The Luggage Compartment Lid Is Inoperative Using The Remote Keyless Entry (RKE) Transmitter: Testing

WARNING: This page is about a different car, the 2005 Mercury Montego, 2005 Ford Freestyle, and 2005 Ford Five Hundred. However, it is still accessible from the selected car via links, so may be relevant.
  1. I1 CHECK THE LUGGAGE COMPARTMENT RELEASE OPERATION FROM THE LUGGAGE COMPARTMENT LID RELEASE SWITCH 
    • Release the luggage compartment lid using the luggage compartment lid release switch.
    • Does the luggage compartment lid release correctly? 
  2. I2 CHECK AND RECORD THE TICs 
    • Monitor the RKE transmitter TIC/DATA through the diagnostic tool menus.
    • Access PROGRAM TIC. Read the alpha-numeric codes in each of the 4 memory locations (TIC1, TIC2, TIC3, and TIC4). Record the codes.
    • Is there a TIC recorded in at least 2 of the 4 memory locations (TIC1, TIC2, TIC3, and TIC4)? 
    • Yes  : GO to I3.
    • No  : PROGRAM all the RKE transmitters. TEST the system for normal operation.
  3. I3 CHECK THE LUGGAGE COMPARTMENT LID RELEASE BUTTON ON THE TRANSMITTER 
    • Monitor the SJB LAST TIC/DATA RECEIVED while pressing and releasing the RKE transmitter luggage compartment lid release button.
    • Does an 8-digit alpha-numeric code appear for the LAST TIC RECEIVED and does the LAST DATA RECEIVED match the button pressed? 
    • Yes  : GO to  I5.
    • No  : GO to I4.
  4. I4 CHECK THE LUGGAGE COMPARTMENT LID RELEASE BUTTON ON THE SECOND RKE TRANSMITTER 
    • Monitor the RKE transmitter TIC/DATA while pressing and releasing the RKE transmitter luggage compartment lid release button of the second RKE transmitter.
    • Does an 8-digit alpha-numeric code appear for the LAST TIC RECEIVED and does the LAST DATA RECEIVED match the button pressed? 
    • Yes  : CHECK the battery of RKE transmitter used in Step  I3. If the battery is OK, a new RKE transmitter is necessary. PROGRAM all RKE transmitters. REFER to REMOTE KEYLESS ENTRY TRANSMITTER PROGRAMMING . TEST the system for normal operation.
    • No  : GO to  I6.
  5. I5 CHECK THE TIC RECEIVED AGAINST THE RECORDED TICs AND COMPARE THE DATA 
    • Monitor the RKE transmitter TIC/DATA using the recorded alpha-numeric codes from Step  I2.
    • Is the TIC received one of the TICs recorded in Step   I2 ? 
  6. I6 CHECK BOTH TRANSMITTER TICs AGAINST THE RECORDED TICs 
    • For each RKE transmitter, monitor the TIC/DATA.
    • Compare the data with the alpha-numeric codes from Step  I2.
    • Is each of the TICs received one of the TICs from Step   I2 ? 
  7. I7 CHECK FOR SJB OPERATION 
    • Disconnect all the SJB connectors.
    • Check for:
      • corrosion
      • pushed-out pins
    • Connect all the SJB connectors and make sure they seat correctly.
    • Operate the system and verify the concern is still present.
    • Is the concern still present? 
    • Yes  : INSTALL a new SJB. REFER to MULTIFUNCTION ELECTRONIC MODULES . PROGRAM all the RKE transmitters, REFER to REMOTE KEYLESS ENTRY TRANSMITTER PROGRAMMING . INFORM the customer that any RKE transmitters not present need to be reprogrammed. TEST the system for normal operation.
    • No  : The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector.
scientia non olet · About LEMON Manuals