LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2006 >> Focus ZX5 SE, Standard >> Repair and Diagnosis >> External Pages >> Different car >> Section 1482 (Engine Controls - Pinpoint Tests (Hybrid)) >> Pinpoint Test TR: Immediate Shutdown (ISDN) 1 and 2 Signals >> Test Procedure

Test Procedure

WARNING: This page is about a different car, the 2011 Mercury Milan, 2011 Lincoln MKZ, 2011 Ford Fusion, 2010 Mercury Milan, and 2010 Ford Fusion. However, it is still accessible from the selected car via links, so may be relevant.
  1. TR1 KEY ON ENGINE OFF (KOEO) AND CONTINUOUS MEMORY DIAGNOSTIC TROUBLE CODE (DTC) P1A0A: VERIFY THE CONCERN IS PRESENT 
    NOTE: Clearing the transaxle control module (TCM) DTCs erases any TCM recorded freeze frame data. Make sure to record any TCM freeze frame information before proceeding any further. Refer to the scan tool instruction manual for freeze frame PID menu.
    • Clear the TCM DTCs.
    • Carry out the TCM self-test.

    Is DTC P1A0A present? 

    Yes No
    GO to  TR2. GO to  TR14.
  2. TR2 CHECK FOR AN IMMEDIATE SHUTDOWN REQUEST FROM BECM 
    • Ignition ON, engine OFF.
    • Access the TCM and monitor the I_SDN_1 (MODE) and I_SDN_2 (MODE) PIDs.

    Do both I_SDN_1 and I_SDN_2 PIDs indicate discharge? 

    Yes No
    GO to  TR3. GO to  TR4.
  3. TR3 VISUAL INSPECTION OF THE ISDN 1 AND 2 CIRCUITS 
    • Visually inspect the ISDN 1 and 2 circuits.
    • Make sure all the ISDN 1 and 2 circuit connectors are properly and securely connected.
    • Examine all the wiring harnesses and connectors for damaged, burned, or overheated insulation, and loose or broken conditions.

    Is a concern present? 

    Yes No
    REPAIR as necessary.
    Clear the TCM DTCs. REPEAT the self-test.    		 An open interlock circuit may be the cause for immediate shutdown.
    REFER to the CHARGING SYSTEM - HIGH VOLTAGE TRACTION BATTERY , Transmission Control Module (TCM) DTC Chart. CARRY OUT the diagnostic steps for DTC P0A0A to continue diagnosis.
  4. TR4 CHECK FOR ISDN1 SIGNAL LOW 
    NOTE: Use the PID reading from the PPT TR2.

    Does only the I_SDN_1 PID indicate discharge? 

    Yes No
    GO to  TR5. GO to  TR9.
  5. TR5 CHECK THE ISDN1 CIRCUIT FOR AN OPEN CIRCUIT IN THE HARNESS 
    • Ignition OFF.
    • Transaxle Assembly-A connector disconnected.
    • Measure the resistance between:
    RESISTANCE REFERENCE CHART

    (+) TB-A Connector, Harness Side (-) Transaxle Assembly-A Connector, Harness Side
    ISDN1 - Pin 15 ISDN1 - Pin 6

    Is the resistance less than 5 ohms? 

    Yes No
    GO to  TR6. REPAIR the circuit.
    Clear the TCM DTCs. REPEAT the self-test.
  6. TR6 CHECK THE ISDN1 CIRCUIT FOR A SHORT TO GROUND IN HARNESS 
    • Measure the resistance between:
    RESISTANCE REFERENCE CHART

    (+) TB-A Connector, Harness Side (-) Vehicle Battery
    ISDN1 - Pin 15 Negative terminal

    Is the resistance greater than 10K ohms? 

    Yes No
    GO to  TR7. REPAIR the circuit.
    Clear the TCM DTCs. REPEAT the self-test.
  7. TR7 CHECK FOR THE ISDN1 CIRCUIT SHORTED TO CIRCUITS IN THE SAME HARNESS 
    • Measure the resistance between:
    RESISTANCE REFERENCE CHART

    (+) Transaxle Assembly-A Connector, Harness Side (-) Transaxle Assembly-A Connector, Harness Side
    ISDN1 - Pin 6 CAN+ - Pin 1
    ISDN1 - Pin 6 CAN- - Pin 7
    ISDN1 - Pin 6 B+ - Pin 12
    ISDN1 - Pin 6 GND - Pin 2, 8
    ISDN1 - Pin 6 VPWR - Pin 4, 5

    Are the resistances greater than 10K ohms? 

    Yes No
    GO to  TR8. REPAIR the circuit.
    Clear the TCM DTCs. REPEAT the self-test.
  8. TR8 SIMULATE ISDN1 NOT DISCHARGE SIGNAL TO THE TCM 
    • TB-A connector connected.
    • Transaxle Assembly-A connector connected.
    • Isolate the ISDN1 circuit at the TB-A connector.
    • Connect a 5 amp fused jumper wire between the following:
      CONNECTOR PINS REFERENCE CHART

      Point A TB-A Connector, Harness Side Point B Vehicle Battery
      ISDN1 - Pin 15 Positive terminal
    • Ignition ON, engine OFF.
    • Access the TCM and monitor the I_SDN_1 (MODE) PID.

    Does the I_SDN_1 PID indicate discharge? 

    Yes No
    INSTALL a new transaxle assembly. Refer to the ELECTRONICALLY CONTROLLED CONTINUOUSLY VARIABLE TRANSMISSION (ECVT) INSTALL a new traction battery. REFER to the CHARGING SYSTEM - HIGH VOLTAGE TRACTION BATTERY
  9. TR9 CHECK FOR ISDN2 SIGNAL LOW 
    NOTE: Use the PID reading from the PPT TR2.

    Does only the I_SDN_2 PID indicate discharge? 

    Yes No
    GO to  TR10. GO to  TR14.
  10. TR10 CHECK THE ISDN2 CIRCUIT FOR AN OPEN CIRCUIT IN THE HARNESS 
    • Ignition OFF.
    • TB-A connector disconnected.
    • Transaxle Assembly-B connector disconnected.
    • Measure the resistance between:
    RESISTANCE REFERENCE CHART

    (+) TB-A Connector, Harness Side (-) Transaxle Assembly-B Connector, Harness Side
    ISDN2 - Pin 29 ISDN2 - Pin 7

    Is the resistance less than 5 ohms? 

    Yes No
    GO to  TR11. REPAIR the circuit.
    Clear the TCM DTCs. REPEAT the self-test.
  11. TR11 CHECK THE ISDN2 CIRCUIT FOR A SHORT TO GROUND IN THE HARNESS 
    • Measure the resistance between:
    RESISTANCE REFERENCE CHART

    (+) Transaxle Assembly-B Connector, Harness Side (-) Vehicle Battery
    ISDN2 - Pin 7 Negative terminal

    Is the resistance greater than 10K ohms? 

    Yes No
    GO to  TR12. REPAIR the circuit.
    Clear the TCM DTCs. REPEAT the self-test.
  12. TR12 CHECK FOR THE ISDN2 CIRCUIT SHORTED TO CIRCUITS IN THE SAME HARNESS 
    • Measure the resistance between:
    RESISTANCE REFERENCE CHART

    (+) Transaxle Assembly-B Connector, Harness Side (-) Transaxle Assembly-B Connector, Harness Side
    ISDN2 - Pin 7 CTO - Pin 1
    ISDN2 - Pin 7 TGAC - Pin 9
    ISDN2 - Pin 7 TMAC - Pin 4
    ISDN2 - Pin 7 GMSDN - Pin 5

    Are the resistances greater than 10K ohms? 

    Yes No
    GO to  TR13. REPAIR the circuit.
    Clear the TCM DTCs. REPEAT the self-test.
  13. TR13 SIMULATE ISDN2 NOT DISCHARGE SIGNAL TO THE TCM 
    • TB-A connector connected.
    • Transaxle Assembly-B connector connected.
    • Isolate the ISDN2 circuit at the TB-A connector.
    • Connect a 5 amp fused jumper wire between the following:
      CONNECTOR PINS REFERENCE CHART

      Point A TB-A Connector, Harness Side Point B Vehicle Battery
      ISDN2 - Pin 29 Positive terminal
    • Ignition ON, engine OFF.
    • Access the TCM and monitor the I_SDN_2 (MODE) PID.

    Does the I_SDN_2 PID indicate discharge? 

    Yes No
    INSTALL a new transaxle assembly. REFER to the ELECTRONICALLY CONTROLLED CONTINUOUSLY VARIABLE TRANSMISSION (ECVT) INSTALL a new traction battery. REFER to the CHARGING SYSTEM - HIGH VOLTAGE TRACTION BATTERY
  14. TR14 CHECK THE ISDN1 CIRCUIT FOR AN INTERMITTENT CONCERN 
    • Ignition ON, engine OFF.
    • Access the TCM and monitor the I_SDN_1 (MODE) PID.
    • Carefully wiggle all accessible wiring and connectors associated with the circuit and look for a change in the PID state.

    Is a concern present during the wiggle test? 

    Yes No
    REPAIR as necessary.
    Clear the TCM DTCs. REPEAT the self-test.    		 GO to  TR15.
  15. TR15 CHECK THE ISDN2 CIRCUIT FOR AN INTERMITTENT CONCERN 
    • Ignition ON, engine OFF.
    • Access the TCM and monitor the I_SDN_2 (MODE) PID.
    • Carefully wiggle all accessible wiring and connectors associated with the circuit and look for a change in the PID state.

    Is a concern present during the wiggle test? 

    Yes No
    REPAIR as necessary.
    Clear the TCM DTCs. REPEAT the self-test.    		 No concern found. The problem may be intermittent.
    GO to PINPOINT TEST Z .
scientia non olet · About LEMON Manuals