LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2006 >> Focus ZX5 SE, Standard >> Repair and Diagnosis >> External Pages >> Different car >> Section 1433 (Automatic Transmission - Automatic Transaxle/Transmission - 4R70E/4R75E) >> In-Vehicle Servicing >> Transmission Support Crossmember >> Installation

Transmission Support Crossmember: Installation

WARNING: This page is about a different car, the 2010 Lincoln Town Car. However, it is still accessible from the selected car via links, so may be relevant.
  1. Position the LH side of the crossmember into the crossmember pocket and loosely install the bolts.
    2. Fig 1: LH Side Crossmember
    GF0014081Courtesy of FORD MOTOR CO.
  2. Position the RH side of the crossmember into the crossmember pocket and loosely install the bolts.
    3. Fig 2: RH Side Crossmember
    GF0014082Courtesy of FORD MOTOR CO.
  3. Tighten the LH crossmember bolts.
    • Tighten to 70 Nm (52 lb-ft).
    4. Fig 3: LH Side Crossmember Bolts
    GF0014079Courtesy of FORD MOTOR CO.
  4. Tighten the RH crossmember bolts.
    • Tighten to 70 Nm (52 lb-ft).
    5. Fig 4: RH Side Crossmember Bolts
    GF0014052Courtesy of FORD MOTOR CO.
  5. Install the parking brake cable bracket.
    • Tighten to 55 Nm (41 lb-ft).
    6. Fig 5: Parking Brake Cable Bracket Bolts
    GF0014054Courtesy of FORD MOTOR CO.
  6. Lower the transmission onto the crossmember and install the rear transmission insulator nuts.
    • Tighten to 30 Nm (22 lb-ft).
    7. Fig 6: Rear Transmission Insulator Nuts
    GF0013674Courtesy of FORD MOTOR CO.
  7. Remove the transmission jack.
  8. Install a new gasket and position the RH catalytic converter assembly in place and loosely install the bolts. Do not tighten the bolts at this time.
    9. Fig 7: RH Catalytic Converter Bolts
    GF0014049Courtesy of FORD MOTOR CO.
  9. Install the RH exhaust flange nuts.
    • Tighten to 48 Nm (35 lb-ft).
    10. Fig 8: RH Exhaust Flange Bolts
    GF0014048Courtesy of FORD MOTOR CO.
  10. Tighten the RH exhaust bolts.
    • Tighten to 40 Nm (30 lb-ft).
    11. Fig 9: RH Catalytic Converter Bolts
    GF0014049Courtesy of FORD MOTOR CO.
  11. Connect the RH HO2S connector.
    12. Fig 10: RH Heated Oxygen Sensor (HO2S) Sensor Connector
    GF0014047Courtesy of FORD MOTOR CO.
  12. Connect the RH catalyst monitor connector.
    13. Fig 11: RH Catalyst Monitor Connector
    G04016678Courtesy of FORD MOTOR CO.
  13. Install a new gasket and position the LH catalytic converter assembly in place and install the bolts. Do not tighten the bolts at this time.
    14. Fig 12: LH Catalytic Converter Bolts
    GF0014051Courtesy of FORD MOTOR CO.
  14. Install the LH exhaust flange nuts.
    • Tighten to 48 Nm (35 lb-ft).
    15. Fig 13: LH Exhaust Flange Bolts
    GF0014067Courtesy of FORD MOTOR CO.
  15. Tighten the LH exhaust bolts.
    • Tighten 40 Nm (30 lb-ft).
    16. Fig 14: LH Catalytic Converter Bolts
    GF0014051Courtesy of FORD MOTOR CO.
  16. Connect the LH HO2S connector.
    17. Fig 15: Identifying LH HO2S Connector
    G04584303Courtesy of FORD MOTOR CO.
  17. Connect the LH catalyst monitor connector.
    18. Fig 16: LH Catalyst Monitor Connector
    G04584304Courtesy of FORD MOTOR CO.
scientia non olet · About LEMON Manuals