Torque Specifications
WARNING: This page is about a different car, the 2008 Ford Econoline, 2008 Ford E450 Super Duty, and 2008 Ford Cutaway. However, it is still accessible from the selected car via links, so may be relevant.
TORQUE SPECIFICATIONS
| Description | Nm | lb-ft | lb-in |
|---|---|---|---|
| A/C compressor bolts | 25 | 18 | - |
| A/C fitting nut | 15 | - | 133 |
| A/C tube bolt | 28 | 21 | - |
| Accessory drive belt idler pulley bolts | 47 | 35 | - |
| Accessory drive belt idler pulley bracket bolts | 25 | 18 | - |
| Accessory drive belt tensioner bolts | 25 | 18 | - |
| Air bag sensor bolts | 12 | - | 106 |
| Banjo fitting bolt at cylinder heads | 38 | 28 | - |
| Battery cable bracket | 22 | 16 | - |
| Block heater | 41 | 30 | - |
| Camshaft follower mounting bolt | 13 | - | 115 |
| Camshaft Position (CMP) sensor | 13 | - | 115 |
| Camshaft thrust plate-mounting bolts | 31 | 23 | - |
| Charge Air Cooler (CAC) duct retaining clamp | 12 | - | 106 |
| Connecting rod bearing boltsa | - | - | - |
| Coolant hose shield nuts | 6 | - | 53 |
| Coolant pump mounting bolts | 23 | 17 | - |
| Coolant pump pulley bolts | 31 | 23 | - |
| Crankcase breather screws | 7 | - | 62 |
| Crankcase-to-head tube | 82 | 60 | - |
| Crankshaft Position (CKP) sensor | 13 | - | 115 |
| Crankshaft pulley bolta | - | - | - |
| Crankshaft pulley bolts (dual generators) | 47 | 35 | - |
| Cylinder block drain plugb | 20 | - | 177 |
| Cylinder head bolt sequence and torquea | - | - | - |
| Cylinder head-to-fuel filter tube | 26 | 19 | - |
| Engine Coolant Temperature (ECT) sensor | 18 | - | 159 |
| Engine front cover bolts | 24 | 18 | - |
| Engine mount-to-crossmember nuts | 90 | 66 | - |
| Engine mount-to-engine mount plate bolts | 80 | 59 | - |
| Engine mount plate-to-cylinder block bolts | 80 | 59 | - |
| Engine mount removable stud | 55 | 41 | - |
| Engine rear cover bolts | 24 | 18 | - |
| Engine Oil Temperature (EOT) sensor | 18 | - | 159 |
| EGR cooler coolant supply port cover (M6) | 10 | - | 89 |
| Exhaust flange nuts | 40 | 30 | - |
| Exhaust manifold flange boltsac | - | - | - |
| Exhaust Pressure (EP) tube assembly at exhaust manifold | 30 | 22 | - |
| Exhaust tube-to-exhaust manifold flange nuts (left side)c | 27 | 20 | - |
| Exhaust tube-to-exhaust manifold flange bolts (right side)c | 27 | 20 | - |
| Fan stator standoff | 47 | 35 | - |
| Flexplate mounting boltsa | - | - | - |
| Fuel Injection Control Pressure (ICP) sensor | 12 | - | 106 |
| Fuel Injection Pressure Regulator (IPR) valve | 50 | 37 | - |
| Fuel injector hold-down bolt | 35 | 26 | - |
| Fuel return tube at secondary fuel filter | 43 | 32 | - |
| Fuel tube bracket nut | 13 | - | 115 |
| Generator mounting bracket bolts (dual generators) | 47 | 35 | - |
| Glow plug module nuts | 8 | - | 71 |
| Glow plugs | 19 | - | 168 |
| Ground strap bolt | 12 | - | 106 |
| Heater tube bolts | 13 | - | 115 |
| High-pressure oil pump cover bolts | 11 | - | 97 |
| High-pressure oil pump discharge tube mounting bolts | 11 | - | 97 |
| High-pressure oil pump mounting bolts | 31 | 23 | - |
| High-pressure oil rail boltsa | - | - | - |
| Hood latch bolts | 12 | - | 106 |
| Intake Air Temperature 2 (IAT2) sensor | 18 | - | 159 |
| Intake manifold flange boltsa | - | - | - |
| LH cylinder head fuel line | 38 | 28 | - |
| Lower crankcase main bearing cap boltsa | - | - | - |
| Lower oil pan bolt | 13 | - | 115 |
| Oil cooler assembly bolts | 22 | 16 | - |
| Oil drain pan plug | 44 | 32 | - |
| Oil filter adapter housing bolts (Torx) | 15 | - | 133 |
| Oil filter assembly bolts | 24 | 18 | - |
| Oil filter mounting bolts (6 mm) | 10 | - | 89 |
| Oil filter mounting bolts (8 mm) | 22 | 16 | - |
| Oil pickup tube flange bolts | 13 | - | 115 |
| Oil pump cover bolts | 13 | - | 115 |
| Piston cooling jet mounting boltd | 13 | - | 115 |
| Power steering pump bolt | 25 | 18 | - |
| Primary generator B+ wire retaining nut | 8 | - | 71 |
| Radiator support bolts | 20 | - | 177 |
| Radiator upper support brackets | 12 | - | 106 |
| Rear engine tube assembly bolt | 13 | - | 115 |
| Rear heat shield bolts (M6 x 1.0 x 1.2) | 11 | - | 97 |
| Rear heat shield bolts (M10 x 1.5 x 16) | 49 | 36 | - |
| Rocker arm carrier bolts | 62 | 46 | - |
| Rocker arm fulcrum plate bolts | 31 | 23 | - |
| Secondary fuel filter assembly bolts | 24 | 18 | - |
| Secondary fuel filter banjo fitting | 35 | 26 | - |
| Secondary fuel filter cover | 14 | - | 124 |
| Secondary generator B+ wire retaining nut | 8 | - | 71 |
| Starter control wire nut | 6 | - | 53 |
| Starter mounting bolts | 25 | 18 | - |
| Starter positive cable nut | 14 | - | 124 |
| Thermostat housing retaining bolts | 23 | 17 | - |
| Torque converter nuts | 35 | 26 | - |
| Transmission cooler tube support bracket bolts | 12 | - | 106 |
| Transmission fluid indicator and tube nut, front | 13 | - | 115 |
| Transmission fluid indicator and tube nut, rear | 8 | - | 71 |
| Transmission-to-engine bolts | 47 | 35 | - |
| Turbocharger-to-exhaust downpipe clamp | 9 | - | 80 |
| Upper oil pan bolts (M6) | 13 | - | 115 |
| Vacuum pump mounting bracket stud bolts | 47 | 35 | - |
| Valve cover bolts and studs | 9 | - | 80 |
| Vibration damper mounting boltsa | - | - | - |
a Refer to the procedure.
b Apply clean engine oil to the O-ring seal before installing.
c Apply High Temperature Nickel Anti-Seize Lubricant (XL-2) to the threads prior to assembly.
d Apply Threadlock 262 to bolt threads prior to assembly.