LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2005 >> Focus ZX5 S, Automatic >> Repair and Diagnosis >> Body & Frame >> Windows And Glass >> Diagnosis And Testing >> Glass, Frames and Mechanisms >> Pinpoint Tests >> Pinpoint Test G: Single Power Window Is Inoperative - Passenger Side

Pinpoint Test G: Single Power Window Is Inoperative - Passenger Side

  1. G1 CHECK FOR VOLTAGE TO THE PASSENGER WINDOW CONTROL SWITCH 
    • Key in ON position.
    • Does the passenger window control switch LED illuminate? 
      • Yes  : Go to  G2.
      • No  : Go to  G5.
  2. G2 CHECK THE PASSENGER WINDOW CONTROL SWITCH GROUND CIRCUITS 
    • Key in OFF position.
    • Disconnect: Passenger Window Control Switch C604.
    • Measure the resistance between the passenger window control switch C604 pin 3, circuit 32-AJ18 (WH/VT) harness side and ground; and between the passenger window control switch C604 pin 6, circuit 33-AJ18 (YE/VT), harness side and ground.
      Fig 1: Checking Passenger Window Control Switch Ground Circuits
      G03952849Courtesy of FORD MOTOR CO.
    • Are the resistances less than 5 ohms? 
      • Yes  : Go to  G3.
      • No  : REPAIR the circuit. TEST the system for normal operation.
  3. G3 CHECK FOR CONTINUITY BETWEEN THE PASSENGER WINDOW CONTROL SWITCH AND THE PASSENGER WINDOW REGULATOR MOTOR 
    • Disconnect: Passenger Window Regulator Motor C623.
    • Measure the resistance between the passenger window control switch C604 pin 1, circuit 33-AJ17 (YE/VT), harness side and the passenger window regulator motor C623 pin 1, circuit 33-AJ17 (YE/VT), harness side.
      Fig 2: Checking For Continuity Between Passenger Window Control Switch And Passenger Window Regulator Motor
      G03952839Courtesy of FORD MOTOR CO.
    • Is the resistance less than 5 ohms? 
      • Yes  : Go to  G4.
      • No  : REPAIR the circuit. TEST the system for normal operation.
  4. G4 CHECK FOR CONTINUITY BETWEEN THE PASSENGER WINDOW CONTROL SWITCH AND THE PASSENGER WINDOW REGULATOR MOTOR 
    • Measure the resistance between the passenger window control switch C604 pin 7, circuit 32-AJ17 (WH/VT), harness side and the passenger window regulator motor C623 pin 2, circuit 32-AJ17 (WH/VT), harness side.
      Fig 3: Checking For Continuity Between Passenger Window Control Switch And Passenger Window Regulator Motor
      G03952840Courtesy of FORD MOTOR CO.
    • Is the resistance less than 5 ohms? 
      • Yes  : INSTALL a new door window regulator motor. REFER to DOOR WINDOW REGULATOR MOTOR . TEST the system for normal operation.
      • No  : REPAIR the circuit. TEST the system for normal operation.
  5. G5 CHECK THE PASSENGER WINDOW CONTROL SWITCH GROUND CIRCUIT 
    • Key in OFF position.
    • Disconnect: Passenger Window Control Switch C604.
    • Measure the resistance between the passenger window control switch C604 pin 4, circuit 31-LH31 (BK), harness side and ground.
      Fig 4: Measuring Resistance Between Passenger Window Control Switch C604 Pin 4, Circuit 31-LH31 (BK), Harness Side And Ground
      G03952835Courtesy of FORD MOTOR CO.
    • Is the resistance less than 5 ohms? 
      • Yes  : Go to  G6.
      • No  : REPAIR the circuit. TEST the system for normal operation.
  6. G6 CHECK FOR VOLTAGE TO THE PASSENGER WINDOW CONTROL SWITCH 
    • Key in ON position.
    • Measure the voltage between the passenger window control switch C604 pin 2, circuit 15-AJ18 (GN/WH), harness side and ground.
      Fig 5: Measuring Voltage Between Passenger Window Control Switch C604 Pin 2, Circuit 15-AJ18 (GN/WH), Harness Side And Ground
      G03952836Courtesy of FORD MOTOR CO.
    • Is the voltage greater than 10 volts? 
      • Yes  : VERIFY the customer concern.
      • No  : REPAIR the circuit. TEST the system for normal operation.
scientia non olet · About LEMON Manuals