LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2005 >> Escape Hybrid, 4WD >> Repair and Diagnosis >> External Pages >> Different car >> Section 1106 (Seating) >> Removal And Installation >> Seat Track - Front >> Removal And Installation

Removal And Installation

WARNING: This page is about a different car, the 2008 Ford RV Cutaway, 2008 Ford Econoline, 2008 Ford E450 Super Duty, and 2008 Ford Cutaway. However, it is still accessible from the selected car via links, so may be relevant.
WARNING: Never probe the electrical connectors on safety belt buckle/retractor pretensioners or adaptive load limiting retractors. Failure to follow this instruction may result in the accidental deployment of the safety belt pretensioners or adaptive load limiting retractors, which increases the risk of serious personal injury or death.
WARNING: To reduce the risk of accidental deployment, do not use any memory saver devices. Failure to follow this instruction may result in serious personal injury or death.
NOTE: The air bag warning indicator illuminates when the restraints control module (RCM) fuse is removed and the ignition switch is ON.
NOTE: The supplemental restraint system (SRS) must be fully operational and free of faults before releasing the vehicle to the customer.
NOTE: Seat tracks and seat motors are only serviceable as a complete seat track assembly.
NOTE: LH shown, RH similar.

All seats 

  1. Remove the seat. For additional information, refer to Seat - Front .
  2. Remove the seat backrest. For additional information, refer to Seat Backrest - Front .
  3. Remove the seat cushion. For additional information, refer to Seat Cushion - Front .

    4. Manual seats 

    NOTE: Use the fastener access holes to reach the seat support nuts.
  4. Remove the 4 riser-to-manual seat track nuts.
    • To install, tighten to 40 Nm (30 lb-ft).
    5. Fig 1: Riser-To-Manual Seat Track Nuts
    GF0011310Courtesy of FORD MOTOR CO.

    Seats with power 

  5. Remove the 2 riser-to-outboard power seat track nuts.
    • To install, tighten to 40 Nm (30 lb-ft).
    6. Fig 2: Riser-To-Outboard Power Seat Track Nuts
    GF0011311Courtesy of FORD MOTOR CO.
  6. Remove the 3 riser-to-inboard power seat track bolts.
    • To install, tighten to 25 Nm (18 lb-ft).
    7. Fig 3: Riser-To-Inboard Power Seat Track Bolts
    GF0011312Courtesy of FORD MOTOR CO.
  7. Disconnect the power seat motor jumper harness electrical connector.
    8. Fig 4: Power Seat Motor Jumper Harness Electrical Connector
    GF0011313Courtesy of FORD MOTOR CO.
    NOTE: Note the connector locations and wire harness routing for installation.
  8. Separate the electrical connector pin-type retainers from the riser and remove the power seat wire harness.

    9. All seats 

    NOTE: Note the connector locations and wire harness routing for installation.
    NOTE: LH shown, RH similar.
  9. Detach the safety belt buckle and pretensioner electrical connector from the seat riser.
  10. Separate the riser from the seat track.
  11. Remove the safety belt buckle and pretensioner.
    1. Remove the bolt.
      • To install, tighten to 40 Nm (30 lb-ft).
    2. Separate the safety belt buckle and pretensioner from the seat track.
    3. Route out the wire harness and remove the safety belt buckle and pretensioner.
    12. Fig 5: Safety Belt Buckle, Bolt & Pretensioner
    GF0011314Courtesy of FORD MOTOR CO.
  12. To install, reverse the removal procedure.
scientia non olet · About LEMON Manuals