Instrument Panel Cluster (IPC) Dealer Test Mode - Non-Hybrid
WARNING: This page is about a different car, the 2011 Mercury Milan, 2011 Lincoln MKZ, and 2011 Ford Fusion. However, it is still accessible from the selected car via links, so may be relevant.
To enter the IPC self-diagnostic mode, begin with the ignition key in the OFF position. Press and hold the message center RESET button. Turn the key to the RUN position and hold the RESET button until the display indicates ENGINEERING TEST MODE, usually within 3 to 5 seconds. Press the RESET button once to advance through each stage of the self-test. To exit the IPC self-test mode, turn the ignition to the OFF position.
NOTE:
If the message center detects a non-resettable fault condition that it is reporting out on such as door ajar, the dealer test mode session cannot be entered until the fault condition has been corrected and the message removed. If the dealer test mode session is interrupted by the fault condition display (such as door ajar), the session can be resumed by pressing the RESET button.
NOTE:
Some of the displays listed in the table below use xxx's to represent a numeric or alpha-numeric value. The value may display the same amount of characters represented by the xxx's or there may be more/less depending on the type of display. For example: VEHICLE SPEED xxxx.x MPH may display VEHICLE SPEED 25 MPH. Note that there were 4 x's in the display description but only 2 digits in the actual display.
FUSION AND MILAN
| First Line Display | Second Line Display | Description |
|---|---|---|
| ENGINEERING | TEST MODE | Initial entry display into the self-test mode. |
| GAUGE | TEST | Carries out the gauge sweep of all gauges, then displays the present gauge values. Also carries out the checksum test on Read-Only Memory (ROM). |
| All VF segments illuminated | - | Carries out the prove-out of all dot matrix pixels in all characters. |
| TELLTALE | TEST | Illuminates all the microprocessor-controlled lamps and LEDs. |
| PART NUMBER | xxxx-xx | Return to normal operation of all microprocessor-controlled lamps/LEDs and displays the alpha-numeric prefix and suffix of the IPC part number. |
| ROM LEVEL | $xxxx | Displays the hexadecimal ROM level and type. |
| Electrically Erasable Programmable Read-Only Memory (EEPROM) LEVEL | $xxxx | Displays the hexadecimal EEPROM level and type. |
| SW RELEASE | xx/xx/xx | Displays the software release date in mm/dd/yy format stored in Non-Volatile Memory (NVM). |
| ROM CHECKSUM | $xxxxxxxx | Shows the ROM checksum data. $xxxxxxxx PASS = passed. $xxxxxxxx FAIL = failed. $- CALC = calculating the checksum. |
| MANUFACTURE DATE | $xxxx | Displays hexadecimal coding of the final manufacturing test date. |
| MANUF CONFIG | BYTE 1 $xx | Displays hexadecimal coding of vehicle options NVM for line 1 of As-Built data for ABS/traction control/interactive vehicle dynamics, oil life threshold, Tire Pressure Monitoring System (TPMS) and Belt-Minder®. |
| B&A CONFIG | BYTE 1-6 $xx | Displays hexadecimal coding of vehicle options NVM for lines 1 through 6 of As-Built data. |
| CONTINUOUS | DTC $xxxxxx | Displays DTCs in 16-bit hexadecimal format. DTCs displayed are those detected in continuous operation not during self-test. If no DTCs are present, the DTC: None is displayed. |
| VEHICLE SPEED | xxx.x MPH | Displays the English speed value being inputs in tenths of mph to the Instrument Panel Cluster (IPC), the speedometer indicates the present filtered speed. If the High Speed Controller Area Network (HS-CAN) message is missing, the second line displays -.- MPH. If the HS-CAN message is invalid, the second line displays INV MPH. If the vehicle speed input is an unknown value, UNKNOWN MPH is displayed. |
| VEHICLE SPEED | xxx.x km/h | Displays the metric speed value being inputs in tenths of km/h to the IPC , the speedometer indicates the present filtered speed. If the HS-CAN message is missing, the second line displays -.- km/h. If the HS-CAN message is invalid, the second line displays INVALID km/h. If the vehicle speed input is an unknown value, UNKNOWN km/h is displayed. |
| TACHOMETER | xxxx RPM | Displays the tachometer value being input in rpm to the IPC . The tachometer indicates the present filtered rpm. If the HS-CAN message is missing, the second line displays -.- RPM. If the HS-CAN message is invalid, the second line displays INV RPM. If the engine speed input is an unknown value, UNKNOWN RPM is displayed. |
| FUEL 1 LEVEL | xxx INSTANT | Displays the present primary (fuel pump module) unfiltered fuel level. 000-009 = short circuit. 010-254 = normal range. 255 = open. INV = invalid input. |
| FUEL 2 LEVEL | xxx INSTANT | Displays the present secondary (fuel level sender) unfiltered fuel level. 000-009 = short circuit. 010-254 = normal range. 255 = open. INV = invalid input. |
| FUEL 1 LEVEL % | STATUS xxx | Display present filtered primary (fuel pump module) input for fuel level percent status. 000-254 = normal range. 0255= open or short circuit detected. INV = invalid input. |
| FUEL 2 LEVEL % | STATUS xxx | Display present filtered secondary (fuel level sender) input for fuel level percent status. 000-254 = normal range. 0255= open or short circuit detected. INV = invalid input. |
| INSTANT DTE | xxx MILES |
NOTE:
This display may differ from the DTE displayed in the INFO menu of the message center due to the use of the unfiltered DTE calculation. Displays the calculated (unfiltered) Distance To Empty (DTE) in miles. - = invalid input. |
| RAFE DTE | xx.x MPG | Displays the running fuel economy in decimal. If the fuel raw average fuel economy message is missing, the second line displays -.- MPG. If the fuel raw average fuel economy message is invalid, the second line displays INVALID MPG. |
| FUEL 1 ON/OF/SZ | xxx xxx | Displays the key on, key off, and zero speed samples for the fuel pump module. If the input is invalid, the message center displays- -. |
| FUEL 2 ON/OF/SZ | xxx xxx xxx | Displays the key on, key off, and zero speed samples for the secondary fuel level input (fuel level sender). If the input is invalid, the message center displays - - -. |
| F1 #S ON/OFF/SZ | xxx xxx xxx | Displays the number of valid samples used for key on, key off, and zero speed samples for the primary fuel level input (fuel pump module). |
| F2 #S ON/OFF/SZ | xxx xxx xxx | Displays the number of valid samples used for key on, key off, and zero speed samples for the secondary fuel level input (fuel level sender). |
| COOLANT TEMP | xxx C | Displays the last temperature gauge input value from the PCM over the HS-CAN in degrees C, temperature gauge indicates the present filtered temperature. If the temperature message is missing, the second line displays - C. If the temperature message is invalid, the second line displays INV C. |
| ODOMETER | xxx COUNTS | Displays the unfiltered odometer rolling count input received over the HS-CAN from the PCM, in decimal. If the odometer rolling count data is missing, the second line displays - COUNTS. If the odometer rolling count data is invalid, the second line displays INV counts. |
| COMPASS TX=$xx | CLUSTER RX=$xx | Display data received from the compass module and transmitted by the IPC to the compass module. If there is a communication concern with the compass module, the message center displays $-. If the compass is configured off, the message center displays, COMPASS CONFIGURED OFF. |
| BATTERY | xxx.x VOLTS | Displays the present battery reading in volts at the IPC input pin. |
| DIMMING CMD | xxx | Displays the dimming command message in percentage from the SJB over the MS-CAN. If the dimming command message is missing, the second line displays -. If the dimming command message is invalid, the second line displays INV. |
| DIMVAL $xx | LITVAL $xx | Displays the dimming and lighting values from the SJB over the MS-CAN. 0-21 = normal range with 0 indicating off. 22-253 = out of range. 254 = unknown value. 255 = invalid value. If the dimming and lighting value messages are missing, the line displays -. If the dimming and lighting value messages are invalid, the line displays INV. If the dimming value is OK and the lighting value is unknown, DIMVAL xxx LITVAL UN is displayed. If the dimming value is invalid and the lighting value is unknown, DIMVAL INV LITVAL UN is displayed. |
| MC SWITCH | xxx A/D CNTS | Displays current message center switch input analog/digital counts in decimal (0-255). |
| LOW WASHER | SWITCH xxxx | Display the hardwired low washer fluid status received from the washer fluid level switch. The message center displays HIGH or LOW depending upon the state of the low washer fluid switch. |
| OIL PRESSURE | SWITCH xxx | Display the hardwired engine oil pressure status received from the engine oil pressure switch. The message center displays HIGH or LOW depending upon the state of the engine oil pressure switch. |
| LAST CHIME | SOUNDED xxxxxx | Displays the last chime that sounded. STBELT = safety belt, AIRBAG = air bag secondary, KEYIN = key in ignition, TRNSIG = turn signal reminder, DOOR = door ajar, HDLMPS = headlamps on, MSGCTR = message center warning tone, PRKBRK = park brake warning, BLTMDR = Belt-Minder® and MEMORY = memory feedback. If the input is unknown, the message center displays -. |
| DIGITAL PORT 0-9, A, B, C, E or F | $xx | Displays 8 bit hexadecimal value of the digital port readings. |
| ANALOG PORT 0-9 | $xx | Displays 10 bit hexadecimal value of the analog port readings. |
| GAUGE | TEST | Repeats the test display cycle. |