LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2005 >> Escape Base, 3.0 1, FWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 1534 (Supplemental Restraint System) >> Diagnostic Tests >> Air Bag and Safety Belt Pretensioner Supplemental Restraint System (SRS) >> DTC Charts

DTC Charts

WARNING: This page is about a different car, the 2010 Lincoln Town Car. However, it is still accessible from the selected car via links, so may be relevant.

The DTCs can be retrieved from the restraints control module (RCM) with a scan tool via the data link connector (DLC).

SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DIAGNOSTIC TROUBLE CODE INDEX

DTCa Description Action To Take
- The Air Bag Warning Indicator is Illuminated Continuously - RCM Disconnected or Inoperative, Loss of Battery Feed or Loss of Signal Ground Go to Pinpoint Test A .
B1231 Event Threshold Exceeded Install a new restraints control module (RCM) and impact sensors. REFER to Inspection and Repair After a Supplemental Restraint System (SRS) Deployment .
B1317 Battery Voltage High CHECK battery voltage; to be below 16 volts. REFER to CHARGING SYSTEM - GENERAL INFORMATION article.
B1318 Battery Voltage Low CHECK battery voltage; to be above 9 volts. REFER to CHARGING SYSTEM - GENERAL INFORMATION article.
B1342 ECU Is Faulted INSTALL a new RCM. REFER to Restraints Control Module (RCM) .
B1869 Lamp Air Bag Warning Indicator Circuit Open Go to Pinpoint Test B .
B1870 Lamp Air Bag Warning Indicator Circuit Short To Battery Go to Pinpoint Test C .
B1884 PAD Warning Lamp Circuit Failure Go to Pinpoint Test D .
B1890 PAD Warning Lamp Circuit Short to Battery Go to Pinpoint Test E .
B1891 Air Bag Tone Warning Indicator Circuit Short to Battery Go to Pinpoint Test F .
B1892 Air Bag Tone Warning Indicator Circuit Failure Go to Pinpoint Test G .
B1921 Air Bag Diagnostic Monitor Ground Circuit Open Go to Pinpoint Test H .
B2290 Occupant Classification System Fault Go to Pinpoint Test I .
B2292 Restraint System - Seatbelt Pretensioner Fault Go to Pinpoint Test J .
B2293 Restraint System - Airbag Fault Go to Pinpoint Test K .
B2295 Restraint System - Side Airbag Fault Go to Pinpoint Test L .
B2296 Restraint System - Impact Sensor Fault Go to Pinpoint Test M .
B2432 Drivers Seat Belt Buckle Switch Circuit Open Go to Pinpoint Test N .
B2433 Drivers Seat Belt Buckle Switch Circuit Short to Battery Go to Pinpoint Test O .
B2434 Drivers Seat Belt Buckle Switch Circuit Short to Ground Go to Pinpoint Test P .
B2435 Driver Safety Belt Buckle Switch Circuit Resistance Out of Range Go to Pinpoint Test Q .
B2436 Passengers Seat Belt Buckle Switch Circuit Open Go to Pinpoint Test R .
B2437 Passengers Seat Belt Buckle Switch Circuit Short to Battery Go to Pinpoint Test S .
B2438 Passengers Seat Belt Buckle Switch Circuit Short to Ground Go to Pinpoint Test T .
B2439 Passengers Seat Belt Buckle Switch Resistance out of Range Go to Pinpoint Test U .
B2477 Module Configuration Error INSTALL a new RCM. REFER to Restraints Control Module (RCM) .
B2792 Cross Link Between Firing Loops Go to Pinpoint Test V .
B2909 Belt Tension Sensor Fault Go to Pinpoint Test W .
B2984 Deployable Steering Column Circuit Open Go to Pinpoint Test X .
B2985 Deployable Steering Column Circuit Short to Battery Go to Pinpoint Test Y .
B2986 Deployable Steering Column Circuit Short to Ground Go to Pinpoint Test Z .
B2987 Deployable Steering Column Circuit Resistance Low on Squib Go to Pinpoint Test AA .
C1414 Incorrect Module Design Level Go to Pinpoint Test AB .
C1946 Front Driver's Seat Track Position Switch Circuit Open Go to Pinpoint Test AC .
C1947 Front Driver's Seat Track Position Switch Circuit Short to Ground Go to Pinpoint Test AD .
C1948 Front Driver's Seat Track Position Switch Circuit Resistance Out of Range Go to Pinpoint Test AE .
C1982 Front Driver's Seat Track Position Switch Circuit Short to Battery Go to Pinpoint Test AF .
- No Communication with the Restraints Control Module (RCM) REFER to MODULE COMMUNICATIONS NETWORK article to diagnose the no communication concern.

a DTC: Retrieved using scan tool.

SUPPLEMENTAL RESTRAINT SYSTEM (SRS) LAMP FAULT CODE (LFC) TABLE

LFCa LFC Priority Description Action To Take
- - No Communication with the Restraints Control Module (RCM) REFER to MODULE COMMUNICATIONS NETWORK article to diagnose the communication concern.
NONE
Secondary Air Bag Warning Sounds if Another Fault is Present
1 Lamp Air Bag Warning Indicator Circuit Short to Battery Go to Pinpoint Test C .
NONE
Continuous Lamp
Secondary Air Bag Warning Sounds if Another Fault is Present
1 Lamp Air Bag Warning Indicator Circuit Open Go to Pinpoint Test B .
Continuous 2 The Air Bag Warning Indicator is Illuminated Continuously - RCM Disconnected or Inoperative, Loss of Battery Feed or Loss of Signal Ground Go to Pinpoint Test A .
Continuous 2 Battery Voltage High CHECK battery voltage; to be below 16 volts. REFER to CHARGING SYSTEM - GENERAL INFORMATION article.
Continuous 2 Battery Voltage Low CHECK battery voltage; to be above 9 volts. REFER to CHARGING SYSTEM - GENERAL INFORMATION article.
Flashing (5Hz) 95 Incorrect Module Design Level (RCM in Plant Mode Fault) INSTALL a new RCM. REFER to Restraints Control Module (RCM) .
1-2 4 ECU is Faulted INSTALL a new RCM. REFER to Restraints Control Module (RCM) .
1-3 5 Event Threshold Exceeded INSTALL a new RCM and impact sensors. REFER to Inspection and Repair After a Supplemental Restraint System (SRS) Deployment .
1-4 6 Air Bag Diagnostic Monitor Ground Circuit Open Go to Pinpoint Test H .
1-5 7 Incorrect Module Design Level (RCM Version Conflicts with OCS Version) Go to Pinpoint Test AB .
1-6 81 Occupant Classification System Fault (OCS Communication) Go to Pinpoint Test I .
1-8 86 PAD Warning Lamp Circuit Failure Go to Pinpoint Test D .
1-9 46 Air Bag Circuit Open - Loop No. 1, Front Driver Side Go to Pinpoint Test K .
2-1 54 Air Bag Circuit Open - Loop No. 1, Front Passenger Side Go to Pinpoint Test K .
2-2 70 Side Air Bag Circuit Open, Front Driver Side Go to Pinpoint Test L .
2-3 74 Side Air Bag Circuit Open, Front Passenger Side Go to Pinpoint Test L .
3-3 62 Pretensioner Circuit Open, Front Driver Side Go to Pinpoint Test J .
3-4 66 Pretensioner Circuit Open, Front Passenger Side Go to Pinpoint Test J .
4-2 19 Driver/Center Front Crash Sensor Communication Fault Go to Pinpoint Test M .
4-3 29 Side Crash Sensor Communication Fault, Front Driver Side Go to Pinpoint Test M .
4-4 34 Side Crash Sensor Communication Fault, Front Passenger Side Go to Pinpoint Test M .
4-9 90 Front Driver's Seat Track Position Switch Circuit Open Go to Pinpoint Test AC .
4-11 17 Driver/Center Front Crash Sensor Mount/Communication Fault Go to Pinpoint Test M .
4-12 27 Side Crash Sensor Mount or Communication Fault, Front Driver Side Go to Pinpoint Test M .
4-13 32 Side Crash Sensor Mount or Communication Fault, Front Passenger Side Go to Pinpoint Test M .
5-1 38 Front Drivers Seat Belt Buckle Switch Circuit Open Go to Pinpoint Test N .
5-2 42 Passengers Seat Belt Buckle Switch Circuit Open Go to Pinpoint Test R .
5-3 94 Air Bag Tone Warning Indicator Circuit Failure Go to Pinpoint Test G .
5-4 12 Module Configuration Error (RCM Configured Incorrectly) INSTALL a new RCM. REFER to Restraints Control Module (RCM) .
6-1 18 Driver/Center Front Crash Sensor Internal Fault Go to Pinpoint Test M .
6-2 28 Side Crash Sensor Internal Fault, Front Driver Side Go to Pinpoint Test M .
6-3 33 Side Crash Sensor Internal Fault, Front Passenger Side Go to Pinpoint Test M .
6-6 16 Driver/Center Front Crash Sensor Circuit Short to Ground Go to Pinpoint Test M .
6-7 26 Side Crash Sensor Circuit Short to Ground, Front Driver Side Go to Pinpoint Test M .
6-8 31 Passenger Front Crash Sensor Circuit Short to Ground Go to Pinpoint Test M .
6-11 15 Driver/Center Front Crash Sensor Circuit Short to Battery Go to Pinpoint Test M .
6-12 25 Side Crash Sensor Circuit Short to Battery, Front Driver Side Go to Pinpoint Test M .
6-13 30 Side Crash Sensor Circuit Short to Battery, Front Passenger Side Go to Pinpoint Test M .
7-1 36 Drivers Seat Belt Buckle Switch Circuit Short to Ground Go to Pinpoint Test P .
7-2 40 Passengers Seat Belt Buckle Switch Circuit Short to Ground Go to Pinpoint Test T .
7-3 88 Front Driver's Seat Track Position Switch Circuit Short to Ground Go to Pinpoint Test AD .
7-5 37 Drivers Seat Belt Buckle Switch Resistance Out of Range Go to Pinpoint Test Q .
7-6 41 Passengers Seat Belt Buckle Switch Resistance Out of Range Go to Pinpoint Test U .
7-7 89 Front Driver's Seat Track Position Switch Circuit Resistance Out of Range Go to Pinpoint Test AE .
7-9 35 Drivers Seat Belt Buckle Switch Circuit Short to Battery Go to Pinpoint Test O .
7-10 39 Passengers Seat Belt Buckle Switch Circuit Short to Battery Go to Pinpoint Test S .
7-11 87 Front Driver's Seat Track Position Switch Circuit Short to Battery Go to Pinpoint Test AF .
7-13 91 Front Passenger Side Belt Tension Sensor Circuit Fault Go to Pinpoint Test W .
7-14 92 Front Passenger Side Belt Tension Sensor Short to Ground Go to Pinpoint Test W .
8-1 50 Air Bag Circuit Open - Loop No. 2, Front Driver Side Go to Pinpoint Test K .
8-2 58 Air Bag Circuit Open - Loop No. 2, Front Passenger Side Go to Pinpoint Test K .
8-3 45 Air Bag Circuit Short to Ground - Loop No. 1, Front Driver Side Go to Pinpoint Test K .
8-4 49 Air Bag Circuit Short to Ground - Loop No. 2, Front Driver Side Go to Pinpoint Test K .
8-5 53 Air Bag Circuit Short to Ground - Loop No. 1, Front Passenger Side Go to Pinpoint Test K .
8-6 57 Air Bag Circuit Short to Ground - Loop No. 2, Front Passenger Side Go to Pinpoint Test K .
8-7 44 Air Bag Circuit Short to Battery - Loop No. 1, Front Driver Side Go to Pinpoint Test K .
8-8 48 Air Bag Circuit Short to Battery - Loop No. 2, Front Driver Side Go to Pinpoint Test K .
8-9 52 Air Bag Circuit Short to Battery - Loop No. 1, Front Passenger Side Go to Pinpoint Test K .
8-10 56 Air Bag Circuit Short to Battery - Loop No. 2, Front Passenger Side Go to Pinpoint Test K .
8-11 47 Air Bag Inflator Circuit Resistance Low - Loop No. 1, Front Driver Side Go to Pinpoint Test K .
8-12 51 Air Bag Inflator Circuit Resistance Low - Loop No. 2, Front Driver Side Go to Pinpoint Test K .
8-13 55 Air Bag Inflator Circuit Resistance Low - Loop No. 1, Front Passenger Side Go to Pinpoint Test K .
8-14 39 Air Bag Inflator Circuit Resistance Low - Loop No. 2, Front Passenger Side Go to Pinpoint Test K .
9-1 69 Side Air Bag Circuit Short to Ground, Front Driver Side Go to Pinpoint Test L .
9-2 73 Side Air Bag Circuit Short to Ground, Front Passenger Side Go to Pinpoint Test L .
9-3 61 Pretensioner Circuit Short to Ground, Front Driver Side Go to Pinpoint Test J .
9-4 65 Pretensioner Circuit Short to Ground, Front Passenger Side Go to Pinpoint Test J .
9-5 68 Driver Seat Side Air Bag Short to Battery Fault Go to Pinpoint Test L .
9-6 72 Side Air Bag Circuit Short to Battery, Front Driver Side Go to Pinpoint Test L .
9-7 60 Pretensioner Circuit Short to Battery, Front Driver Side Go to Pinpoint Test J .
9-8 64 Pretensioner Circuit Short to Battery, Front Passenger Side Go to Pinpoint Test J .
9-9 71 Side Air Bag Circuit Resistance Low, Front Driver Side Go to Pinpoint Test L .
9-10 75 Side Air Bag Circuit Resistance Low, Front Passenger Side Go to Pinpoint Test L .
9-11 63 Pretensioner Circuit Resistance Low, Front Driver Side Go to Pinpoint Test J .
9-12 67 Pretensioner Circuit Resistance Low, Front Passenger Side Go to Pinpoint Test J .
10-14 85 PAD Warning Lamp Circuit Short To Battery Go to Pinpoint Test E .
10-15 93 Air Bag Tone Warning Indicator Circuit Short to Battery Go to Pinpoint Test F .
11-1 8 Incorrect Module Design Level (RCM Version Conflicts with LH Front Impact Severity Sensor Version) Go to Pinpoint Test AB .
11-2 10 Incorrect Module Design Level (RCM Version Conflicts with Driver Side Impact Sensor Version) Go to Pinpoint Test AB .
11-3 11 Incorrect Module Design Level (RCM Version Conflicts with Passenger Side Impact Sensor Version) Go to Pinpoint Test AB .
11-6 13 Module Configuration Error (Restraints Component Installed But not Expected: OCS) INSTALL a new RCM. REFER to Restraints Control Module (RCM) .
11-7 14 Module Configuration Error (Restraints Component Installed But not Expected: PAD Indicator) INSTALL a new RCM. REFER to Restraints Control Module (RCM) .
11-8 80 Generic OCS Module Fault, Front Pass. Side Go to Pinpoint Test I .
11-9 83 OCS Calibration Fault, Front Pass. Side Go to Pinpoint Test I .
11-10 82 OSC Sensing element fault, front passenger side Go to Pinpoint Test I .
11-11 84 Occupant Classification Sensor Mounting Fault, Front Passenger Side Go to Pinpoint Test I .
12-1 9 Incorrect Module Design Level (RCM Version Conflicts with RH Front Impact Severity Sensor Version) Go to Pinpoint Test AB .
12-2 22 Passenger Front Crash Sensor Mount/Communication Fault Go to Pinpoint Test M .
12-3 23 Passenger Front Crash Sensor Internal Fault Go to Pinpoint Test M .
12-4 24 Passenger Front Crash Sensor Communication Fault Go to Pinpoint Test M .
12-5 21 Passenger Front Crash Sensor Circuit Short to Ground Go to Pinpoint Test M .
12-6 20 Passenger Front Crash Sensor Circuit Short to Battery Go to Pinpoint Test M .
12-7 78 Deployable Steering Column Circuit Open Go to Pinpoint Test X .
12-8 76 Deployable Steering Column Circuit Short to Battery Go to Pinpoint Test Y .
12-9 77 Deployable Steering Column Circuit Short to Ground Go to Pinpoint Test Z .
12-10 79 Deployable Steering Column Circuit Resistance Low on Squib Go to Pinpoint Test AA .
12-11 43 Cross Link Between Firing Loops Go to Pinpoint Test V .

a LFC: Flashed on air bag warning indicator.