Torque Specifications: 4R100
WARNING: This page is about a different car, the 2003 Ford Pickup, 2003 Ford F550 Super Duty, 2003 Ford F450 Super Duty, and 2003 Ford Excursion. However, it is still accessible from the selected car via links, so may be relevant.
TORQUE SPECIFICATIONS (TRANSMISSION - 4R100)
| Application | Ft. Lbs. (N.m) | |
|---|---|---|
| Auxiliary Cooler Tube | 8-10 (11-14) | |
| Auxiliary Cooler Tube | 16-22 (22-30) | |
| Control Assembly-To-Pump | 18-23 (24-31) | |
| Cooler Line Fitting-To-CBV | 20 (27) | |
| Cooler Bypass Valve Fitting-To-Case (Front) | 22 (30) | |
| Cooler Bypass Valve Fitting-To-Case (Rear) | 27 (37) | |
| Drive Shaft Bolt | ||
| Except Excursion | 26 (35) | |
| Excursion | 82 (111) | |
| Extension Housing-To-Case | 30-40 (41-54) | |
| Flexplate Inspection Cover-To-Case (Diesel) | 15 (20) | |
| Flexplate Inspection Cover-To-Case (Gasoline) | 25 (34) | |
| Inner Manual Valve Detent Lever Nut | 35 (47) | |
| Intermediate/Overdrive Cylinder Fluid Feed Bolt (Front) | 12 (16) | |
| Line Pressure-To-Case Plug | 6-12 (8-16) | |
| Low/Reverse OWC Inner Race-To-Case | 18-25 (24-34) | |
| Pump Body-To-Case | 18-23 (24-31) | |
| Parking Pawl Abutment-To-Case | 18 (25) | |
| Parking Rod Guide Plate-To-Case | 18 (25) | |
| Radiator Nipple Connector | 17-23 (23-31) | |
| Radiator-To-Tube Connector | 18-22 (24-30) | |
| Starter Mounting Bolt | 16-20 (22-28) | |
| Torque Converter Drain Plug | 18-20 (24-27) | |
| Torque Converter-To-Flexplate Nut | 26 (35) | |
| Transmission Insulator & Retainer-To-Case | 60-80 (81-108) | |
| Transmission Insulator & Retainer-To-Crossmember Nut | 69 (94) | |
| Transmission Oil Pan Bolts | 11 (15) | |
| Transmission Support Crossmember-To-Frame Nut | 60 (81) | |
| Transmission-To-Engine Bolts | ||
| Diesel | 45 (61) | |
| Gasoline | 35 (48) | |
| INCH Lbs. (N.m) | ||
| Digital Transmission Range Sensor | 75-85 (8-10) | |
| Main Accumulator & Solenoid Body-To-Case | 80-100 (9-11) | |
| Main & Lower Control Body-To-Case | 80-100 (9-11) | |
| Manual Control Valve Detent Lever Spring-To-Case | 89 (10) | |
| Output Shaft Speed Sensor | 70-88 (8-10) | |
| Reinforcing Plate-To-Case | 80-100 (9-11) | |
| Stator Support-To-Pump Body | 80-100 (9-11) | |
| Turbine Shaft Speed Sensor | 70-88 (8-10) | |