LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2002 >> Escape 3.0 1, FWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 1848 (Manual Transmission - ZF S6-650 & M6HD - 6-Speed -- F250-F550 Super Duty (2007)) >> Installation >> Transmission - Gasoline Engines >> All vehicles

All vehicles

WARNING: This page does not describe the selected car, but rather 8 other vehicles, including the 2007 Ford Pickup, 2007 Ford F550 Super Duty, 2007 Ford F450 Super Duty, 2007 Ford Cab & Chassis, and 2006 Ford Pickup. However, it is still accessible from the selected car via links, so may be relevant.
  1. Using the transmission jack, raise and position the transmission to the engine and clutch.
    2. Fig 1: Transmission-To-Engine Bolts (With Specifications)
    GF0007393Courtesy of FORD MOTOR CO.
  2. Install the seven transmission-to-engine bolts.
    3. Fig 2: Left Crossmember Bolts (With Specifications)
    GF0007394Courtesy of FORD MOTOR CO.
  3. Position the crossmember in the vehicle. Install the LH crossmember bolts.
    4. Fig 3: Right Crossmember Bolts (With Specifications)
    GF0007395Courtesy of FORD MOTOR CO.
  4. Install the RH crossmember nuts.
    5. Fig 4: Transmission Mount Nuts (With Specifications)
    GF0007396Courtesy of FORD MOTOR CO.
  5. Install the transmission mount nuts.
  6. Attach the wire harness to the crossmember.
    7. Fig 5: Dust Cover Bolts (With Specifications)
    GF0007397Courtesy of FORD MOTOR CO.
  7. Install the dust cover bolts.
    8. Fig 6: Dust Cover Bolt (With Specifications)
    GF0007398Courtesy of FORD MOTOR CO.
  8. Remove the transmission jack.
    9. Fig 7: Transmission Cooler Tubes (With Specifications)
    GF0007399Courtesy of FORD MOTOR CO.
  9. Connect the transmission cooler tubes.
    10. Fig 8: Clutch Slave Cylinder
    GF0007400Courtesy of FORD MOTOR CO.
  10. Install the clutch slave cylinder.
    • Rotate the clutch slave cylinder clockwise 45 degrees to lock in position.
  11. Install the starter. For additional information, refer to STARTING SYSTEM - DIESEL ENGINE article.
  12. Install the exhaust Y-pipe. For additional information, refer to EXHAUST SYSTEM article.
  13. Install the transfer case, if equipped. For additional information, refer to TRANSFER CASE article.
    • If the transfer case control lever assembly was removed from the transmission, it must be correctly aligned.
  14. Connect the driveshaft.
  15. Install any power take-off (PTO) equipment, if equipped.
    16. Fig 9: Fuel Line Bracket
    GF0007187Courtesy of FORD MOTOR CO.
  16. Connect the fuel lines to the transmission.
    17. Fig 10: Reverse Lamp Switch Electrical Connector
    GF0007192Courtesy of FORD MOTOR CO.
  17. Connect the reverse lamp switch electrical connector.
    18. Fig 11: Wiring Harness
    GF0007193Courtesy of FORD MOTOR CO.
  18. Connect the wiring harness to the transmission.
  19. Refill the transmission to specification.
    • Refill the transmission with clean transmission fluid.
  20. Lower the vehicle.
    21. Fig 12: Gearshift Lever & Shift Housing Assembly (With Specifications)
    GF0007401Courtesy of FORD MOTOR CO.
    CAUTION: Do not use a silicone sealing compound.
    NOTE: Do not wait longer than ten minutes to tighten the six bolts due to the rapid cure time of the sealant.
  21. Install the gearshift lever and shift housing assembly.
    • Apply gasket maker to the shift housing and the main case.
    22. Fig 13: Lower Shift Lever Boot
    GF0007177Courtesy of FORD MOTOR CO.
  22. Install the lower shift lever boot.
    23. Fig 14: Gearshift Lever Bolts (With Specifications)
    GF0007402Courtesy of FORD MOTOR CO.
  23. Apply threadlock and sealer to the gearshift lever bolts. Install the upper gearshift lever.
    24. Fig 15: Locating Gearshift Lever Boot Screws
    GF0005212Courtesy of FORD MOTOR CO.
  24. Install the screws.
scientia non olet · About LEMON Manuals