LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2002 >> Cutaway 7.3 F >> Repair and Diagnosis >> External Pages >> Different car >> Section 2994 (Windows & Glass - Glass, Frames And Mechanisms -- F250-F550 Super Duty) >> Diagnosis And Testing >> Glass, Frames and Mechanisms >> Pinpoint Tests >> Pinpoint Test C: A Single Power Window is Inoperative - LH Front >> Pinpoint Test C: A Single Power Window Is Inoperative - LH Front

Pinpoint Test C: A Single Power Window Is Inoperative - LH Front

WARNING: This page is about a different car, the 2011 Ford Pickup, 2011 Ford F550 Super Duty, 2011 Ford F450 Super Duty, and 2011 Ford Cab & Chassis. However, it is still accessible from the selected car via links, so may be relevant.
NOTE: Use the correct probe adapter(s) when making measurements. Failure to use the correct probe adapter(s) may damage the connector.
NOTE: If the LH front window is already in the full DOWN position, skip to pinpoint Step C2.
  1. C1 CHECK THE LH FRONT POWER WINDOW DOWN OPERATION 
    • Ignition OFF.
    • Disconnect: LH Front Window Control Switch C504A (Crew Cab) or C535 (regular and SuperCab).
    • Ignition ON.
    • For regular or SuperCab, connect a fused jumper wire between LH front window control switch C535-7, circuit CBP01 (BU), harness side and LH window control switch C535-1, circuit CPW10 (YE/VT), harness side; and between LH front window control switch C535-5, circuit CPW11 (BU/GY), harness side and LH front window control switch C535-2, circuit GD137 (BK/WH), harness side.
      Fig 1: Connecting Fused Jumper Wire Between LH Front Window Control Switch C535-7 And C535-1 Connector End View
      G07485971Courtesy of FORD MOTOR CO.
    • For Crew Cab, connect a fused jumper wire between LH front window control switch C504A-2, circuit CBP01 (BU), harness side and LH window control switch C504A-1, circuit CPW10 (YE/VT), harness side; and between LH front window control switch C504A-5, circuit CPW11 (BU/GY), harness side and ground.
      Fig 2: Connecting Fused Jumper Wire Between LH Front Window Control Switch C504A-2 And C504A-1 Connector End View
      G07485972Courtesy of FORD MOTOR CO.
    • Does the LH front window move down? 
    • Yes:  REMOVE the jumper wires. GO to  C2.
    • No:  REMOVE the jumper wires. GO to  C3.
  2. C2 CHECK THE LH FRONT POWER WINDOW UP OPERATION 
    • Ignition ON.
    • For regular or SuperCab, connect a fused jumper wire between LH front window control switch C535-7, circuit CBP01 (BU), harness side and LH window control switch C535-5, circuit CPW11 (BU/GY), harness side; and between LH front window control switch C535-1, circuit CPW10 (YE/VT), harness side and LH front window control switch C535-2, circuit GD137 (BK/WH), harness side.
      Fig 3: Connecting Fused Jumper Wire Between LH Front Window Control Switch C535-7 And C535-5 Connector End View
      G07485973Courtesy of FORD MOTOR CO.
    • For Crew Cab, connect a fused jumper wire between LH front window control switch C504A-2, circuit CBP01 (BU), harness side and LH window control switch C504A-5, circuit CPW11 (BU/GY), harness side; and between LH front window control switch C504A-1, circuit CPW10 (YE/VT), harness side and ground.
      Fig 4: Connecting Fused Jumper Wire Between LH Front Window Control Switch C504A-2 And C504A-5 Connector End View
      G07485974Courtesy of FORD MOTOR CO.
    • Does the LH front window move up? 
    • Yes:  INSTALL a new LH front window control switch. REFER to WINDOW CONTROL SWITCH .
    • No:  REMOVE the jumper wires. GO to  C3.
  3. C3 CHECK WINDOW MOTOR CIRCUIT FOR AN OPEN 
    • Ignition OFF.
    • Disconnect: LH Front Window Motor C524.
    • Measure the resistance between LH front window motor C524-2, circuit CPW10 (YE/VT), harness side and LH front window control switch C535-1 (regular and SuperCab) or C504A-1 (Crew Cab), circuit CPW10 (YE/VT), harness side.
      Fig 5: Measuring Resistance Between LH Front Window Motor And LH Front Window Control Switch Connector End View
      G07485975Courtesy of FORD MOTOR CO.
    • Is the resistance less than 5 ohms? 
    • Yes:  GO to  C4.
    • No:  REPAIR the circuit. TEST the system for normal operation.
  4. C4 CHECK WINDOW MOTOR CIRCUIT FOR AN OPEN 
    • Measure the resistance between LH front window motor C524-1, circuit CPW11 (BU/GY), harness side and LH front window control switch C535-5 (regular and SuperCab) or C504A-5 (Crew Cab), circuit CPW11 (BU/GY), harness side.
      Fig 6: Measuring Resistance Between LH Front Window Motor And LH Front Window Control Switch Connector End View
      G07485976Courtesy of FORD MOTOR CO.
    • Is the resistance less than 5 ohms? 
    • Yes:  VERIFY there are no mechanical binding conditions preventing the glass mechanism from operating correctly. If a mechanical binding issue is found, REPAIR as necessary. If no mechanical binding condition exists, INSTALL a new LH front window motor. REFER to WINDOW REGULATOR MOTOR - FRONT DOOR . TEST the system for normal operation.
    • No:  REPAIR the circuit. TEST the system for normal operation.
scientia non olet · About LEMON Manuals