LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2002 >> Cutaway 7.3 F >> Repair and Diagnosis >> External Pages >> Different car >> Section 2913 (Automatic Transmission 5R110W (TORQSHIFT(R)) -- F450-F550 Super Duty) >> Diagnosis & Testing >> Diagnostic Trouble Code (DTC) Charts >> Diagnostic Trouble Code (DTC) Chart

Diagnostic Trouble Code (DTC) Chart

WARNING: This page is about a different car, the 2011 Ford F550 Super Duty and 2011 Ford F450 Super Duty. However, it is still accessible from the selected car via links, so may be relevant.
DTC CHART

DTC Component Description Condition Symptom Action
P0657 Actuator Supply Voltage A Actuator Supply Voltage A high side power supply circuit failed Actuator Supply Voltage A high side power supply circuit failed. Only REVERSE, NEUTRAL and 5th gear available. Engine rpm at idle is about 1,000 rpm when Actuator Supply Voltage A is off as a Failure Mode Effect Management action. Power to all solenoids has been interrupted. CHECK for opens, short to ground and the harness disconnected. REPAIR as required. When Actuator Supply Voltage A is commanded OFF as a Failure Mode Effect Management action, CHECK all solenoids for correct function as listed in the Clutch, Solenoid, Application Chart . For additional information on diagnosing PCM concerns, REFER to the INTRODUCTION .
P0706 Transmission Range (TR) Sensor TR  sensor frequency fault detected TR  sensor signal frequency is out of normal range. Only REVERSE, NEUTRAL and 5th gear detected. Engine may not crank. GO to PINPOINT TEST C .
P0707 TR  Sensor TR  sensor circuit duty cycle low input TR  sensor signal duty cycle is below threshold, sensor/circuit electrical malfunction. Only REVERSE, NEUTRAL and 5th gear detected. Engine may not crank. GO to PINPOINT TEST C .
P0708 TR  Sensor TR  sensor circuit duty cycle high input TR  sensor signal duty cycle is above threshold, sensor/circuit electrical malfunction. Only REVERSE, NEUTRAL and 5th gear detected. Engine may not crank. GO to PINPOINT TEST C .
P0710 TFT  Sensor 157°C (315°F) indicated, TFT  sensor circuit grounded
OR
-40°C (-40°F) indicated, TFT  sensor circuit open		 Voltage drop across TFT  sensor exceeds scale set for temperature of 157°C (315°F).
OR
Voltage drop across TFT  sensor exceeds scale set for temperature of -40°C (-40°F).		 No 5th or 6th gears. GO to PINPOINT TEST B .
P0711 Transmission Fluid Temperature (TFT) Sensor No change if TFT  during operation PCM has detected no TFT  change during operation. TFT  stuck at some normal reading. No 5th or 6th gears. GO to PINPOINT TEST B .
P0712 TFT  Sensor 157°C (315°F) indicated, TFT  sensor circuit grounded Voltage drop across TFT  sensor exceeds scale set for temperature of 157°C (315°F). No 5th or 6th gears. GO to PINPOINT TEST B .
P0713 TFT  Sensor -40°C (-40°F) indicated, TFT  sensor circuit open Voltage drop across TFT  sensor exceeds scale set for temperature of -40°C (-40°F). No 5th or 6th gears. GO to PINPOINT TEST B .
P0715 Turbine Shaft Speed (TSS) Sensor Insufficient input from TSS  PCM detected a loss of TSS  signal during operation. Harsh shifts and engagements, engine rpm higher or lower than expected. No 1st, 3rd or 5th gear. GO to PINPOINT TEST D .
P0717 TSS  Sensor No TSS  signal PCM has not detected a TSS  signal. Harsh shifts and engagements, engine rpm higher or lower than expected. No 1st, 3rd or 5th gear. GO to PINPOINT TEST D .
P0718 TSS  Sensor TSS  signal noisy PCM has detected a noisy TSS  signal. - GO to PINPOINT TEST D .
P0720 Output Shaft Speed (OSS) Sensor Insufficient input from OSS  PCM detected a loss of OSS  signal during operation. No 1st, 2nd, 3rd, 4th or 6th gear. GO to PINPOINT TEST D .
P0721 OSS  Sensor OSS  signal noisy PCM has detected a noisy OSS  signal. - GO to PINPOINT TEST D .
P0722 OSS  Sensor No OSS  signal PCM has detected no OSS  signal. No 1st, 2nd, 3rd, 4th or 6th gear. GO to PINPOINT TEST D .
P0730 Clutch Control Solenoid or Internal Parts Gear ratio error PCM has detected a gear ratio error. One-Way Clutch (OWC) clutch or clutches may have failed. Incorrect gear selection depending on failure or mode and manual lever position. Shift errors may also be due to other internal transmission concerns (stuck valves, damaged friction material). Engine rpm could be higher or lower than expected. May flash Transmission Control Indicator Lamp (TCIL). REFER to the Solenoid Application charts located at the beginning of Pinpoint Tests - OSC Equipped Vehicles. If other solenoid DTCs are present, GO to PINPOINT TEST A . If only P0730 and/or 2700 series DTCs are present, INSTALL the appropriate clutch solenoid. CLEAR the DTCs, and ROAD TEST the vehicle. If the concern is still present, REPAIR/INSTALL new internal transmission components.
P0740 Torque Converter Clutch (TCC) Solenoid TCC  solenoid open circuit failure TCC  solenoid circuit fails to provide voltage drop across solenoid. Circuit open. Open circuit: TCC  never engages. GO to PINPOINT TEST A .
P0741 TCC  Solenoid TCC  solenoid circuit performance error Torque converter slippage detected during engagement command indicating a concern with mechanical or hydraulic operation of the TCC  . TCC  slippage when commanded on indicating a concern with the mechanical or hydraulic TCC  operation. No TCC  engagement. REFER to DIAGNOSIS BY SYMPTOM  in this service information.
P0742 TCC  Solenoid TCC  solenoid circuit shorted to ground TCC  solenoid circuit fails to provide voltage drop across solenoid. Shorted to ground. Short circuit: Only 5th gear at low vehicle speeds. GO to PINPOINT TEST A .
P0743 TCC  Solenoid TCC  solenoid circuit failure TCC  solenoid circuit fails to provide voltage drop across solenoid. Circuit open, shorted or PCM driver failure during OBD  test. Open circuit: TCC  never engages. Maximum Pressure Control Solenoid A (PCA) pressure, harsh engagement and shifts. Short circuit: Only 5th gear. GO to PINPOINT TEST A .
P0744 TCC  Solenoid TCC  solenoid circuit shorted to power TCC  solenoid circuit fails to provide voltage drop across solenoid. Circuit shorted to power. No torque converter engagement. GO to PINPOINT TEST A .
P0748 PCA  PCA  circuit failure Voltage through PCA  is checked. An error will be noted if parameters are exceeded. Open circuit: maximum PCA  pressure, harsh engagements and shifts. Engine rpm higher than expected. Only 5th gear present. Maximum PCA  pressure, harsh engagements and shifts. Engine rpm higher than expected. GO to PINPOINT TEST E .
P0750 Shift Solenoid Pressure Control A (SSPCA) Coast Clutch SSPCA  circuit open SSPCA  circuit failed to provide voltage drop across solenoid. Circuit open or PCM driver failure during OBD  test. No 2nd, 4th or 6th gear. GO to PINPOINT TEST A .
P0751 SSPCA  Solenoid SSPCA  solenoid performance or stuck OFF SSPCA  solenoid failed in the OFF position during operation resulting in the coast clutch being applied due to inverse controlled solenoid. Tow/Haul OFF or ON:
  • No 1st, 3rd or 5th gears available.
 REFER to DIAGNOSIS BY SYMPTOM  in this service information.
P0752 SSPCA  Solenoid SSPCA  solenoid stuck ON SSPCA  solenoid failed in the ON position during operation resulting in the coast clutch being released due to inverse controlled solenoid. Tow/Haul OFF or ON:
  • No 2nd, 4th or 6th gears available.
 REFER to DIAGNOSIS BY SYMPTOM  in this service information.
P0753 SSPCA  Coast Clutch SSPCA  circuit failure SSPCA  circuit failed to provide voltage drop across solenoid. Circuit failure or PCM driver failure. Tow/Haul OFF or O/D  ON:
  • No 2nd, 4th, 5th or 6th gears available.
  • No gears available.

Tow/Haul ON or O/D  OFF:
  • No 1st, 2nd, 3rd, 4th or 6th gears available.
 GO to PINPOINT TEST A .
P0755 Shift Solenoid Pressure Control B (SSPCB) Overdrive Clutch SSPCB  circuit open SSPCB  circuit, clutch or solenoid failed to provide voltage drop across solenoid. Circuit open or PCM driver failure during OBD  test. Tow/Haul OFF or O/D  ON:
  • Only 1st or 3rd gears available.

Tow/Haul ON or O/D  OFF:
  • Only 5th gear available.
 GO to PINPOINT TEST A .
P0756 SSPCB  Overdrive Clutch SSPCB  clutch or solenoid - OFF SSPCB  clutch or solenoid failed in the OFF position during operation resulting in LOW pressure in the hydraulic circuit. Tow/Haul OFF or O/D  ON:
  • No 2nd gear available.

Tow/Haul ON or O/D  OFF:

  • No 2nd, 4th or 6th gears available.
 REFER to DIAGNOSIS BY SYMPTOM  in this service information.
P0757 SSPCB  Overdrive Clutch SSPCB  clutch or solenoid failure - ON SSPCB  clutch or solenoid failed in the ON position during operation resulting in HIGH pressure in the hydraulic circuit. No 1st, 3rd or 5th gears available. REFER to DIAGNOSIS BY SYMPTOM  in this service information.
P0758 SSPCB  Overdrive Clutch SSPCB  circuit failure SSPCB  circuit failed to provide voltage drop across solenoid. Circuit failure or PCM driver failure. Tow/Haul OFF or O/D  ON:
  • Only 1st or 3rd gears available.
  • No 2nd gear available.

Tow/Haul ON or O/D  OFF:
  • No 5th gear available.
  • Only 4th, 5th and 6th gears available.
 GO to PINPOINT TEST A .
P0760 Shift Solenoid Pressure Control C (SSPCC) Intermediate Clutch SSPCC  circuit open SSPCC  circuit failed to provide voltage drop across solenoid. Circuit open or PCM drive failure during OBD  test. Tow/Haul OFF or O/D  ON:
  • Only 1st and 2nd gears available.

Tow/Haul ON or O/D  OFF:
  • Only 5th gear available.
 GO to PINPOINT TEST A .
P0761 SSPCC  Intermediate Clutch SSPCC  clutch or solenoid failure - OFF SSPCC  clutch or solenoid failed in the OFF position during operation resulting in LOW pressure in the hydraulic circuit. No 3rd and 4th gear available. REFER to DIAGNOSIS BY SYMPTOM  in this service information.
P0762 SSPCC  Intermediate Clutch SSPCC  clutch or solenoid failure - ON SSPCC  clutch or solenoid failed in the ON position during operation resulting in HIGH pressure in the hydraulic circuit. Only 3rd and 4th gear available. REFER to DIAGNOSIS BY SYMPTOM  in this service information.
P0763 SSPCC  Intermediate Clutch SSPCC  circuit failure SSPCC  circuit failed to provide voltage drop across solenoid. Circuit failure or PCM driver failure. Tow/Haul OFF or O/D  ON:
  • Only 1st, 2nd and 3rd gears available.

Tow/Haul ON or O/D  OFF:
  • Only 4th and 5th gear available.
 GO to PINPOINT TEST A .
P0765 Shift Solenoid Pressure Control D (SSPCD) Direct Clutch SSPCD  circuit open SSPCD  circuit failed to provide voltage drop across solenoid. Circuit open or PCM driver failure during OBD  test. Tow/Haul OFF or O/D  ON:
  • Only 5th gear available.

Tow/Haul ON or O/D  OFF:
  • Only 6th gear available.
 GO to PINPOINT TEST A .
P0766 SSPCD  Direct Clutch SSPCD  clutch or solenoid failure - OFF SSPCD  clutch or solenoid failed in the OFF position during operation resulting in HIGH pressure in the hydraulic circuit. Tow/Haul OFF or O/D  ON:
  • No 5th gear available.

Tow/Haul ON or O/D  OFF:
  • No 5th or 6th gears available.
 REFER to DIAGNOSIS BY SYMPTOM  in this service information.
P0767 SSPCD  Direct Clutch SSPCD  clutch or solenoid failure - ON SSPCD  clutch or solenoid failed in the ON position during operation resulting in LOW pressure in the hydraulic circuit. No 1st, 2nd, 3rd or 4th gears available. REFER to DIAGNOSIS BY SYMPTOM  in this service information.
P0768 SSPCD  Direct Clutch SSPCD  circuit failure SSPCD  circuit failed to provide voltage drop across solenoid. Circuit failure or PCM driver failure. Tow/Haul OFF or O/D  ON:
  • Only 1st, 2nd and 5th gears available.

Tow/Haul ON or O/D  OFF:
  • Only 5th and 6th gear available.
 GO to PINPOINT TEST A .
P0770 Shift Solenoid Pressure Control E (SSPCE) Low/ Reverse Clutch SSPCE  circuit open SSPCE  circuit failed to provide voltage drop across solenoid. Circuit open or PCM drive failure during OBD  test. Tow/Haul OFF or O/D  ON:
  • Only 1st and 2nd gears available.

Tow/Haul ON or O/D  OFF:
  • Only 5th gear available.
 GO to PINPOINT TEST A .
P0771 SSPCE  Low/ Reverse Clutch SSPCE  clutch or solenoid failure - OFF SSPCE  clutch or solenoid failed in the OFF position during operation resulting in LOW pressure in the hydraulic circuit. Tow/Haul OFF or O/D  ON:
  • No 1st gear available.

Tow/Haul ON or O/D  OFF:
  • No 1st or 2nd gears available.
 REFER to DIAGNOSIS BY SYMPTOM  in this service information.
P0772 SSPCE  Low/ Reverse Clutch SSPCE  clutch or solenoid failure - ON SSPCE  clutch or solenoid failed in the ON position during operation resulting in HIGH pressure in the hydraulic circuit. Tow/Haul OFF or O/D  ON:
  • Only 1st gear available.

Tow/Haul ON or O/D  OFF:
  • Only 1st or 2nd gears available.
 REFER to DIAGNOSIS BY SYMPTOM  in this service information.
P0773 SSPCE  Low/ Reverse Clutch SSPCE  circuit failure SSPCE  circuit failed to provide voltage drop across solenoid. Circuit failure or PCM driver failure. Tow/Haul OFF or O/D  ON:
  • Only 1st and 2nd gears available.

Tow/Haul ON or O/D  OFF:
  • Only 5th gear available.
 GO to PINPOINT TEST A .
P0791 Intermediate Shaft Speed Sensor Insufficient input from intermediate shaft speed sensor PCM detected an insufficient signal from the intermediate shaft speed sensor during operation. Harsh shifts or engagements, engine rpm higher or lower than expected. No 1st, 3rd or 5th gears. GO to PINPOINT TEST D .
P0793 Intermediate Shaft Speed Sensor No input from intermediate shaft speed sensor PCM detected a loss of intermediate shaft speed sensor signal during operation. Harsh shifts or engagements, engine rpm higher or lower than expected. No 1st, 3rd or 5th gears. GO to PINPOINT TEST D .
P0794 Intermediate Shaft Speed Sensor Intermediate shaft speed sensor signal intermittent PCM has detected an intermittent intermediate shaft speed sensor signal. - GO to PINPOINT TEST D .
P0960 PCA  PCA  circuit open failure Voltage through PCA  is checked. An error will be noted if parameters are exceeded. Open circuit: maximum PCA  pressure, harsh engagements and shifts. Engine rpm higher than expected. GO to PINPOINT TEST E .
P0962 PCA  PCA  short to ground circuit failure Voltage through PCA  is checked. An error will be noted if parameters are exceeded. Short circuit: Only 5th gear present. GO to PINPOINT TEST E .
P0963 PCA  PCA  short to power circuit failure Voltage through PCA  is checked. An error will be noted if parameters are exceeded. Maximum PCA  pressure, harsh engagements and shifts. Engine rpm higher than expected. GO to PINPOINT TEST E .
P0973 SSPCA  Coast Circuit SSPCA  or circuit shorted to ground Voltage through SSPCA  circuit is checked. An error will be noted if tolerance is exceeded. Short to ground failure detected. Tow/Haul OFF or O/D  ON:
  • No 2nd, 4th, 5th or 6th gears available.

Tow/Haul ON or O/D  OFF:
  • No 1st, 2nd, 3rd, 4th or 6th gears available.
 GO to PINPOINT TEST A .
P0974 SSPCA  Coast Clutch SSPCA  or circuit shorted to power Voltage through SSPCA  circuit is checked. An error will be noted if tolerance is exceeded. Short to power failure detected. Tow/Haul OFF or O/D  ON:
  • No gears available.

Tow/Haul ON or O/D  OFF:
  • No 2nd, 4th or 6th gears available.
 GO to PINPOINT TEST A .
P0976 SSPCB  Overdrive Clutch SSPCB  or circuit shorted to ground Voltage through SSPCB  circuit is checked. An error will be noted if parameters are exceeded. Short to ground failure detected. Tow/Haul OFF or O/D  ON:
  • No 2nd gear available.

Tow/Haul ON or O/D  OFF:

  • Only 4th and 6th gears available.
 GO to PINPOINT TEST A .
P0977 SSPCB  Overdrive Clutch SSPCB  or circuit shorted to power Voltage through SSPCB  circuit is checked. An error will be noted if parameters are exceeded. Short to power failure detected. Tow/Haul OFF or O/D  ON:
  • Only 1st and 3rd gears available.

Tow/Haul ON or O/D  OFF:
  • Only 5th gear available.
 GO to PINPOINT TEST A .
P0979 SSPCC  Intermediate Clutch SSPCC  or circuit shorted to ground Voltage through SSPCC  circuit is checked. An error will be noted if parameters are exceeded. Short to ground failure detected. Tow/Haul OFF or O/D  ON:
  • Only 3rd gear available.

Tow/Haul ON or O/D  OFF:
  • Only 4th gear available.
 GO to PINPOINT TEST A .
P0980 SSPCC  Intermediate Clutch SSPCC  or circuit shorted to power Voltage through SSPCC  circuit is checked. An error will be noted if parameters are exceeded. Short to power failure detected. Tow/Haul OFF or O/D  ON:
  • Only 1st and 2nd gear available.

Tow/Haul ON or O/D  OFF:
  • Only 5th gear available.
 GO to PINPOINT TEST A .
P0982 SSPCD  Direct Clutch SSPCD  or circuit shorted to ground Voltage through SSPCD  circuit is checked. An error will be noted if parameters are exceeded. Short to ground failure detected. Tow/Haul OFF or O/D  ON:
  • Only 1st and 2nd gears available.

Tow/Haul ON or O/D  OFF:
  • Only 5th gear available.
 GO to PINPOINT TEST A .
P0983 SSPCD  Direct Clutch SSPCD  or circuit shorted to power Voltage through SSPCD  circuit is checked. An error will be noted if parameters are exceeded. Short to power failure detected. Tow/Haul OFF or O/D  ON:
  • Only 5th gear available.

Tow/Haul ON or O/D  OFF:
  • Only 6th gear available.
 GO to PINPOINT TEST A .
P0985 SSPCE  Low/ Reverse Clutch SSPCE  or circuit shorted to ground Voltage through SSPCE  circuit is checked. An error will be noted if parameters are exceeded. Short to ground failure detected. Tow/Haul ON or O/D  OFF:
  • Only 5th gear available.
 GO to PINPOINT TEST A .
P0986 SSPCE  Low/ Reverse Clutch SSPCE  or circuit shorted to power Voltage through SSPCE  circuit is checked. An error will be noted if parameters are exceeded. Short to power failure detected. Tow/Haul OFF or O/D  ON:
  • Only 1st and 2nd gears available.

Tow/Haul ON or O/D  OFF:
  • Only 5th gear available.
 GO to PINPOINT TEST A .
P1702 TR  Sensor TR  error TR  sensor error detected. Only REVERSE, NEUTRAL and 5th gear detected. Engine may not crank. GO to PINPOINT TEST C .
P1705 TR  Sensor TR  sensor not in P or N positions during Key ON Engine OFF (KOEO) or Key ON Engine Running (KOER) KOEO  or KOER  not run in P or N positions, or TR  sensor circuit failure. DTC is set. RERUN KOEO  and KOER  in the P or N position. GO to PINPOINT TEST C .
P1711 TFT  Sensor TFT  out of range during KOEO  or KOER  Transmission not operating at temperature during KOEO  or KOER  test. DTC set: engine cold or overheated. Warm or cool the engine to normal operating temperature. RERUN KOEO  and KOER  test. GO to PINPOINT TEST B .
P1744 TCC  Solenoid TCC  solenoid circuit performance error Torque converter slippage detected during engagement command indicating a concern with mechanical or hydraulic operation of the TCC  . TCC  slippage when commanded on indicating a concern with the mechanical or hydraulic TCC  operation. No TCC  engagement. REFER to DIAGNOSIS BY SYMPTOM  in this service information.
P1780 Transmission Control Switch (TCS) TCS  input incorrect per selected position TCS  voltage incorrect. No Tow/Haul feature when the TCS  is pressed during self test. RERUN OBD  test and cycle the TCS  switch. If concern is still present, REFER to AUTOMATIC TRANSMISSION EXTERNAL CONTROLS article.
P1783 TFT  Sensor Transmission overtemp condition indicated TFT  exceeded 127°C (270°F). Torque converter engages earlier than expected. GO to PINPOINT TEST B .
P1910 Backup lamp driver circuit Backup lamp driver control circuit failed Backup lamp driver control circuit failed. No backup lamps in reverse. TR  sensor is OK. REFER to EXTERIOR LIGHTING SYSTEM article.
P2700 Coast Clutch Coast clutch failed on or off The PCM has detected a failure within the coast clutch system. Not all gears available. Tow/Haul OFF or O/D  ON:
  • No 1st, 2nd, 3rd or 5th gears available.

Tow/Haul ON or O/D  OFF:
  • No 1st, 2nd, 4th or 5th gears available.
 Coast clutch failed on or off. REFER to the Solenoid Application charts located at the beginning of Pinpoint Tests - OSC Equipped Vehicles. If other solenoid DTCs are present, GO to PINPOINT TEST A . If only P0730 and/or 2700 series DTCs are present, INSTALL the appropriate clutch solenoid. CLEAR the DTCs and ROAD TEST the vehicle. If the concern is still present, REPAIR/INSTALL new internal transmission components.
P2701 Overdrive Clutch Overdrive clutch failed ON or OFF The PCM has detected a failure within the overdrive clutch system. Not all gears available. Tow/Haul OFF or O/D  ON:
  • No 1st, 2nd, 3rd or 5th gears available.

Tow/Haul ON or O/D  OFF:
  • No 2nd, 4th or 6th gears available.
 Overdrive clutch failed ON or OFF. REFER to the Solenoid Application charts located at the beginning of Pinpoint Tests - OSC Equipped Vehicles. If other solenoid DTCs are present, GO to PINPOINT TEST A . If only P0730 and/or 2700 series DTCs are present, INSTALL the appropriate clutch solenoid. CLEAR the DTCs and ROAD TEST the vehicle. If the concern is still present, REPAIR/INSTALL new internal transmission components.
P2702 Intermediate Clutch Intermediate clutch failed ON or OFF The PCM has detected a failure within the intermediate clutch system. Not all gears available.
  • No 3rd and 4th gears available.
  • Only 3rd and 4th gears available.
 Intermediate clutch failed ON or OFF. REFER to the Solenoid Application charts located at the beginning of Pinpoint Tests - OSC Equipped Vehicles. If other solenoid DTCs are present, GO to PINPOINT TEST A . If only P0730 and/or 2700 series DTCs are present, INSTALL the appropriate clutch solenoid. CLEAR the DTCs and ROAD TEST the vehicle. If the concern is still present, REPAIR/INSTALL new internal transmission components.
P2703 Direct Clutch Direct clutch failed ON or OFF The PCM has detected a failure within the direct clutch system. Not all gears available. Tow/Haul OFF or O/D  ON:
  • No 1st, 2nd, 3rd or 4th gears available.
  • No 5th or 6th gears available.
 Direct clutch failed ON or OFF. REFER to the Solenoid Application charts located at the beginning of Pinpoint Tests - OSC Equipped Vehicles. If other solenoid DTCs are present, GO to PINPOINT TEST A . If only P0730 and/or 2700 series DTCs are present, INSTALL the appropriate clutch solenoid. CLEAR the DTCs and ROAD TEST the vehicle. If the concern is still present, REPAIR/INSTALL new internal transmission components.
P2704 Low Reverse Clutch Low reverse clutch failed ON or OFF The PCM has detected a failure within the low reverse clutch system. Not all gears available. Tow/Haul OFF or O/D  ON:
  • No 1st gear available.
  • Only 1st gear available.

Tow/Haul ON or O/D  OFF:

  • No 1st or 2nd gears available.
  • Only 1st or 2nd gears available.
 Low reverse clutch failed ON or OFF. REFER to the Solenoid Application charts located at the beginning of Pinpoint Tests - OSC Equipped Vehicles. If other solenoid DTCs are present, GO to PINPOINT TEST A . If only P0730 and/or 2700 series DTCs are present, INSTALL the appropriate clutch solenoid. CLEAR the DTCs and ROAD TEST the vehicle. If the concern is still present, REPAIR/INSTALL new internal transmission components.
scientia non olet · About LEMON Manuals