Torque Specifications
WARNING: This page is about a different car, the 2008 Ford Pickup, 2008 Ford F550 Super Duty, 2008 Ford F450 Super Duty, and 2008 Ford Cab & Chassis. However, it is still accessible from the selected car via links, so may be relevant.
TORQUE SPECIFICATIONS
| Description | Nm | lb-ft | lb-in |
|---|---|---|---|
| Accessory drive belt idler pulley bolt | 47 | 35 | - |
| Accessory drive belt tensioner bolt | 47 | 35 | - |
| A/C compressor bolts | 25 | 18 | - |
| A/C drive belt tensioner bolt | 47 | 35 | - |
| A/C hose nut | 15 | - | 133 |
| Air cleaner outlet pipe clamps | 5 | - | 44 |
| Automatic transmission fluid indicator tube nut | 8 | - | 71 |
| Battery cable bracket nut | 25 | 18 | - |
| Battery cable nut | 10 | - | 89 |
| Battery ground cable-to-engine block bolt | 47 | 35 | - |
| Block heater | 41 | 30 | - |
| Body bolts | 90 | 66 | - |
| Body ground strap bolt | 25 | 18 | - |
| Camshaft position (CMP) sensor | 13 | - | 115 |
| Camshaft thrust plate-mounting bolts | 31 | 23 | - |
| Charge air cooler (CAC) duct clamps (metal duct side) | 8 | - | 71 |
| CAC duct clamps (engine and CAC side) | 12 | - | 106 |
| Connecting rod bearing cap boltsa | - | - | - |
| Coolant pump bolts | 31 | 23 | - |
| Coolant pump pulley bolts | 31 | 23 | - |
| Cooling fan stator nuts and bolts | 25 | 18 | - |
| Cooling fan stator stand offs | 47 | 35 | - |
| Crankcase main bearing cap bolts | d | - | - |
| Crankcase vent oil separator bolts | 13 | - | 115 |
| Crankcase vent oil separator tube clip bolts | 25 | 18 | - |
| Crankcase vent oil separator tube retaining nut | 13 | - | 115 |
| Crankshaft position (CKP) sensor | 13 | - | 115 |
| Crankshaft pulley boltsa | - | - | - |
| Cylinder block coolant drain plugb | 20 | - | 177 |
| Cylinder head boltsa | - | - | - |
| Degas bottle tray bolts | 19 | - | 168 |
| Engine front cover bolts | 31 | 23 | - |
| Engine mount center bolt | 350 | 258 | - |
| Engine mount nuts - LH | 200 | 148 | - |
| Engine mount nuts - RH | 115 | 85 | - |
| Engine mount-to-engine bracket boltsa | - | - | - |
| Engine rear cover bolts (M8) | 31 | 23 | - |
| Engine rear cover bolts (M10) | 62 | 46 | - |
| Engine wire harness bolt | 8 | - | 71 |
| EGR coolant adapter bolt | 13 | - | 115 |
| EGR coolant hose constant tension worm gear clamps | 4 | - | 35 |
| EGR cooler clampsa | - | - | - |
| EGR cooler coolant tube bolts | 13 | - | 115 |
| EGR cooler hose clamp | 4 | - | 35 |
| EGR cooler outlet studs | 17 | - | 150 |
| EGR-oxidation catalytic converter (OC) bracket bolt-to-cylinder block | 62 | 46 | - |
| EGR-OC bracket bolts | 31 | 23 | - |
| EGR-OC bracket nut and bolt | 31 | 23 | - |
| EGR-OC tube-to-horizontal EGR cooler bolts | 31 | 23 | - |
| EGR-OC tube-to-right inlet pipe bolts | 31 | 23 | - |
| EGRT sensor - inlet | 44 | 32 | - |
| Exhaust downpipe bolts | 40 | 30 | - |
| Exhaust manifold bolts and stud boltsa | - | - | - |
| Exhaust manifold flange studs | 18 | - | 159 |
| Exhaust manifold heat shield mounting nuts and bolts | 19 | - | 168 |
| Exhaust manifold heat shield spacers | 19 | - | 168 |
| Exhaust pressure (EP) sensor connector-to-EGR OC tube fitting | 27 | 20 | - |
| EP sensor mounting nut | 9 | - | 80 |
| EP sensor tube nut | 20 | - | 177 |
| Fan clutch hub-to-coolant pump | 150 | 111 | - |
| Flywheel/flexplate mounting boltsa | - | - | - |
| Front bumper mounting bolts | 47 | 35 | - |
| Front end accessory drive nuts and bolts | 47 | 35 | - |
| Front end accessory drive studs (with pre-applied sealant) | 9 | - | 80 |
| Front impact severity sensor bolt | 12 | - | 106 |
| Fuel cooler boltsa | - | - | - |
| Fuel cooler nutsa | - | - | - |
| Fuel cooler stud boltsa | - | - | - |
| Fuel cooling pump bolts | 3 | - | 27 |
| Fuel filter cap | 27 | 20 | - |
| Fuel filter module bolts | 13 | - | 115 |
| Fuel injection pump supply tube retainer nuts | 11 | - | 97 |
| Fuel injector hold-down bolta | - | - | - |
| Fuel injector return tube nut-to-check valve | 28 | 21 | - |
| Fuel injector return tube retainer bolts | 13 | - | 115 |
| Fuel injector return tube retainer nut | 11 | - | 97 |
| Fuel pump heat shield fuel line bracket | 7 | - | 62 |
| Fuel pump heat shield nuts and bolts | 13 | - | 115 |
| Fuel rail supply tubea | - | - | - |
| Fuel rail supply tube retainer bolts | 13 | - | 115 |
| Fuel return plug (back of head) | 27 | 20 | - |
| Fuel supply and return tube clamp bolt | 31 | 23 | - |
| Generator B+ wire nut | 8 | - | 71 |
| Glow plug | 14 | - | 124 |
| Glow plug module mounting bracket bolts | 13 | - | 115 |
| Ground wire nut | 13 | - | 115 |
| Heater hose tube nut and bolts (supply and return) | 13 | - | 115 |
| High-pressure fuel pump cover bolts | 13 | - | 115 |
| High-pressure fuel pump gear bolt | 78 | 58 | - |
| High-pressure fuel pump mounting bolts | 62 | 46 | - |
| High-pressure fuel pump tube nut | 38 | 28 | - |
| High-pressure fuel tube fittingsa | - | - | - |
| High pressure pump adapter (303-765) | 12 | - | 106 |
| High-pressure rail mounting boltsa | - | - | - |
| Hood bolts | 13 | - | 115 |
| Horizontal EGR cooler outlet nuts | 31 | 23 | - |
| Intake manifold boltsa | - | - | - |
| Intake throttle adapter bolts | 10 | - | 89 |
| LH valve cover bracket assembly nuts | 31 | 23 | - |
| LH valve cover bracket nuts | 9 | - | 80 |
| Lower crankcase main bearing boltsa | - | - | - |
| M12 banjo bolts with copper sealing washers | 38 | 28 | - |
| M12 banjo bolts with steel washers (Viton inserts) | 25 | 18 | - |
| M14 banjo bolts | 47 | 35 | - |
| Master cylinder nuts | 30 | 22 | - |
| Oil cooler bolts | 31 | 23 | - |
| Oil cooler cover screws - new cover | 10 | - | 89 |
| Oil cooler cover screws - used cover | 7 | - | 62 |
| Oil filter cap | 25 | 18 | - |
| Oil filter housing bolts | 22 | 16 | - |
| Oil filter return tube screw - new | 7 | - | 62 |
| Oil filter return tube screw - used | 5 | - | 44 |
| Oil level indicator tube bolt | 13 | - | 115 |
| Oil level indicator tube nut | 31 | 23 | - |
| Oil pan bolt - lower | 13 | - | 115 |
| Oil pan bolts - upper | 13 | - | 115 |
| Oil pan drain plug | 44 | 32 | - |
| Oil pickup tube flange bolts | 13 | - | 115 |
| Oil pressure regulator plug | 35 | 26 | - |
| Oil pump housing bolts - long bolts | 31 | 23 | - |
| Oil pump housing bolts - short bolts | 22 | 16 | - |
| Piston cooling tube boltc | 13 | - | 115 |
| Power steering pump bolts | 25 | 18 | - |
| Power steering tube nut | 25 | 18 | - |
| RH engine mount studs | 80 | 59 | - |
| Rocker arm assembly boltsa | - | - | - |
| Running board bolts | 13 | - | 115 |
| Starter control wire nut | 6 | - | 53 |
| Starter mounting bolts | 25 | 18 | - |
| Starter positive cable nut | 12 | - | 106 |
| Steering damper nut | 35 | 26 | - |
| Steering shaft bolt | 48 | 35 | - |
| Thermostat housing retaining bolts | 13 | - | 115 |
| Torque converter nuts | 35 | 26 | - |
| Transmission cooler tubes nut | 9 | - | 80 |
| Transmission external filter tube nuts (early build) | 40 | 30 | - |
| Transmission mount nuts | 115 | 85 | - |
| Transmission-to-engine bolts | 47 | 35 | - |
| Turbocharger bolts (M14, socket head, class 12.9) | 201 | 148 | - |
| Turbocharger crossover tube bolts | 31 | 23 | - |
| Turbocharger downpipe clamp nut | 15 | - | 133 |
| Turbocharger heat shield bolts | 11 | - | 97 |
| Turbocharger inlet pipe-to-exhaust manifold nuts | 31 | 23 | - |
| Turbocharger inlet pipe-to-turbocharger bolts | 25 | 18 | - |
| Turbocharger lifting bracket bolts (303-1266) | 20 | - | 177 |
| Turbocharger oil supply banjo bolts | 38 | 28 | - |
| Turbocharger oil supply standoff fittings | 47 | 35 | - |
| Turbocharger oil supply tube bolt | 13 | - | 115 |
| Turbocharger pedestal bolts | 62 | 46 | - |
| Valve cover base bolts | 13 | - | 115 |
| Valve cover bolts | 9 | - | 80 |
| Valve tappet guide bolts | 13 | - | 115 |
| Vertical EGR cooler bracket bolt (M10) | 62 | 46 | - |
| Vertical EGR cooler bracket bolts (M8) | 31 | 23 | - |
| Vertical EGR cooler-to-EGR valve housing nut and bolt | 31 | 23 | - |
| Vertical EGR cooler-to-EGR valve housing stud | 31 | 23 | - |
| Vertical EGR cooler retaining clip nut | 12 | - | 106 |
a Refer to the procedure.
b Apply clean engine oil before installing.
c Apply Threadlock 262 to the bolt threads prior to installing.
d See step ( 13) in ENGINE ASSEMBLY.