LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2002 >> Cutaway 7.3 F >> Repair and Diagnosis >> External Pages >> Different car >> Section 2436 (Engine - 6.4L 99R Diesel -- F250-F550 Super Duty) >> In-Vehicle Servicing >> Engine Mount - LH, Body On >> Removal

Engine Mount - LH, Body On: Removal

WARNING: This page is about a different car, the 2008 Ford Pickup, 2008 Ford F550 Super Duty, 2008 Ford F450 Super Duty, and 2008 Ford Cab & Chassis. However, it is still accessible from the selected car via links, so may be relevant.
NOTE: Position a suitable protective material in front of the Charge Air Cooler (CAC) or damage to the CAC may occur.
NOTE: It is recommended that this component be serviced with the vehicle body partially lifted. If the vehicle body can be partially lifted, refer to Engine Mount - LH, Partial Body Lift .

All vehicles 

  1. Disconnect the battery ground cables. For additional information, refer to BATTERY, MOUNTING AND CABLES article.
  2. Remove the turbocharger. Carry out the Turbocharger - Body On procedure. For additional information, refer to FUEL CHARGING AND CONTROLS - TURBOCHARGER article.
  3. Remove the upper cooling fan shroud. For additional information, refer to ENGINE COOLING article.

    4. Vehicles with dual generator 

  4. Remove the secondary generator. For additional information, refer to GENERATOR AND REGULATOR article.

    5. Vehicles with brake vacuum pump (belt driven) 

  5. Remove the brake vacuum pump. For additional information, refer to POWER BRAKE ACTUATION article.

    6. All vehicles 

  6. Disconnect the windshield washer hose.
    7. Fig 1: Locating Windshield Washer Hose
    GF0048570Courtesy of FORD MOTOR CO.
  7. Disconnect the underhood light electrical connector and pin-type retainers. Position the wiring aside.
    8. Fig 2: Locating Underhood Light Electrical Connector & Pin-Type Retainers
    GF0048571Courtesy of FORD MOTOR CO.
    NOTE: Mark the location of the hinges prior to removing the hood.
  8. With the help of an assistant, disconnect the hood lift rods. Remove the 4 bolts and the hood.
    9. Fig 3: Locating Hood Lift Rods
    GF0048572Courtesy of FORD MOTOR CO.
  9. Disconnect the crankcase vent oil separator drain tube.
    10. Fig 4: Locating Crankcase Vent Oil Separator Tube From Crankcase Vent Oil Separator
    GF0048441Courtesy of FORD MOTOR CO.
  10. Remove the 4 bolts and the crankcase vent oil separator.
    • Remove and discard the press-in-place gasket.
    11. Fig 5: Locating Crankcase Vent Oil Separator Bolts
    GF0048442Courtesy of FORD MOTOR CO.
  11. Disconnect the PCM electrical connector and wire retainer.
    12. Fig 6: Locating PCM Electrical Connector & Wire Retainer
    GF0048589Courtesy of FORD MOTOR CO.
  12. Remove the 3 push nuts and glow plug module heat shield.
    • Discard the push nuts.
    13. Fig 7: Locating Glow Plug Module Heat Shield & Push Nuts
    GF0048590Courtesy of FORD MOTOR CO.
  13. Disconnect the glow plug module electrical connectors.
    • Position the glow plug electrical connectors out from under the cowl.
    14. Fig 8: Locating Glow Plug Module Electrical Connectors
    GF0048591Courtesy of FORD MOTOR CO.
  14. Remove the 2 nuts and glow plug module.
    15. Fig 9: Locating Glow Plug Module & Retaining Nuts
    GF0048592Courtesy of FORD MOTOR CO.
  15. Disconnect the Exhaust Gas Recirculation Temperature (EGRT) sensor electrical connector from the glow plug bracket.
    16. Fig 10: Locating Exhaust Gas Recirculation Temperature (EGRT) Sensor Electrical Connector
    GF0048593Courtesy of FORD MOTOR CO.
  16. Remove the EGR-Oxidation Catalytic Converter (OC) pipe from the vehicle.
    17. Fig 11: Locating EGR-Oxidation Catalytic Converter (OC) Pipe
    GF0048486Courtesy of FORD MOTOR CO.
    NOTE: Engine removed from the vehicle for clarity.
  17. Remove the bolt and the 5 retaining nuts for the high-pressure fuel injection pump heat shield. Remove the fuel tube bracket and position the ground strap.
    18. Fig 12: Locating Bolt & Retaining Nuts
    GF0048444Courtesy of FORD MOTOR CO.
    NOTE: High-pressure fuel injection pump heat shield removed for clarity.
  18. Remove the remaining 2 bolts and the high-pressure fuel injection pump heat shield.
    19. Fig 13: Locating High-Pressure Fuel Injection Pump Heat Shield Bolts
    GF0048487Courtesy of FORD MOTOR CO.
  19. Remove the RH turbocharger inlet pipe.
    20. Fig 14: Locating RH Turbocharger Inlet Pipe
    GF0048488Courtesy of FORD MOTOR CO.
  20. Remove and discard the 4 RH engine mount retaining nuts.
    21. Fig 15: Locating RH Engine Mount Retaining Nuts
    GF0048574Courtesy of FORD MOTOR CO.
  21. Remove and discard the 2 upper studs for the RH motor mount.
    22. Fig 16: Locating Upper Studs From RH Motor Mount
    GF0048594Courtesy of FORD MOTOR CO.
  22. Remove and discard the 3 LH engine mount retaining nuts.
    23. Fig 17: Locating LH Engine Mount Retaining Nuts
    GF0048575Courtesy of FORD MOTOR CO.
  23. Loosen the 2 transmission mount retaining nuts.
    24. Fig 18: Locating Transmission Mount Retaining Nuts
    GF0048576Courtesy of FORD MOTOR CO.
  24. Remove the 2 exhaust downpipe bolts.
    25. Fig 19: Locating Exhaust Downpipe-To-Oxidation Catalytic Converter (OC) Pipe Bolts
    GF0048543Courtesy of FORD MOTOR CO.
  25. Remove the bolt and position aside the ground cable.
    26. Fig 20: Locating Ground Cable Bolt
    GF0048595Courtesy of FORD MOTOR CO.
  26. Remove the retaining nut for the transmission cooler tubes. Disconnect the transmission cooler tubes from the stud.
    27. Fig 21: Locating Transmission Cooler Tubes & Stud
    GF0048577Courtesy of FORD MOTOR CO.
  27. Remove the bolt. Remove the oil level indicator and tube and position aside.
    • Remove and discard the O-ring seal.
    28. Fig 22: Locating Oil Level Indicator Tube Bolt
    GF0048598Courtesy of FORD MOTOR CO.
  28. Disconnect the fuel hoses at the engine.
    • Plug or cap the openings.
    29. Fig 23: Locating Fuel Hoses At Engine
    GF0048614Courtesy of FORD MOTOR CO.
  29. Install the Engine Lifting Bracket on the Front End Accessory Drive (FEAD) bracket.
    30. Fig 24: Installing Special Tool (303-050) On Front End Accessory Drive (FEAD) Bracket
    GF0048586Courtesy of FORD MOTOR CO.
    NOTE: Use a Heavy Duty Lifting Crane and load leveler rated at a minimum of 907 kg (2,000 lb) or damage to the vehicle may occur.
    NOTE: It will be necessary to position the exhaust downpipe aside to get the lift that is required to remove the engine mount.
  30. Position the Heavy Duty Lifting Crane with a commercially available load leveler and attach the chains to the front of the engine.
    31. Fig 25: Positioning Heavy Duty Lifting Crane With A Commercially Available Load Leveler
    GF0048587Courtesy of FORD MOTOR CO.
    NOTE: Make sure the exhaust downpipe is loose during the raising of the engine or damage to the vehicle may occur.
  31. Raise the Heavy Duty Lifting Crane as needed to get the required lift to remove the LH engine mount.
  32. Support the engine with jackstands or other suitable support devices.
  33. Remove and discard the center bolt for the LH engine mount.
    • Separate the engine mount from the bracket.
    34. NOTE: The engine mount bracket bolts must be discarded and new bolts installed or damage to the vehicle may occur. They are a torque-to-yield design and cannot be reused.
  34. Remove and discard the 4 bolts and the LH engine mount bracket and mount.
    • Rotate the LH engine mount bracket to the front and then remove the LH engine mount. Remove the LH engine mount bracket.
    • Position the spacer on the engine mount bracket out to aid installing the new engine mount.
scientia non olet · About LEMON Manuals