LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2000 >> Taurus LX, 3.0 2, AX4N >> Repair and Diagnosis >> External Pages >> Different car >> Section 648 (Supplemental Inflatable Restraint System - F250-F550 Super Duty) >> Removal And Installation >> Clockspring >> Installation

Removal And Installation: Clockspring: Installation

WARNING: This page is about a different car, the 2006 Ford Pickup, 2006 Ford F550 Super Duty, 2006 Ford F450 Super Duty, and 2006 Ford Cab & Chassis. However, it is still accessible from the selected car via links, so may be relevant.

    Vehicles receiving a new clockspring 

    NOTE: A new clockspring is supplied in a centralized position and held there with a key.
  1. Remove the key from the clockspring, holding the rotor in its centralized position.
    • Do not allow the clockspring rotor to turn.

    2. Vehicles needing clockspring recentering 

    WARNING: Incorrect centralization may result in premature component failure. If in doubt when centralizing the clockspring, repeat the centralizing procedure. Failure to follow this instruction may result in personal injury.
    CAUTION: Make sure the road wheels are in the straight ahead position.
    NOTE: If a clockspring has rotated out of center, follow through with this step.
  2. Centralize the clockspring.
    1. Hold the clockspring outer housing stationary.
    2. Push and release the anti-rotation tab.
      3. CAUTION: Overturning will destroy the clockspring. The internal ribbon wire acts as the stop and can be broken from its internal connection.
    3. While holding the anti-rotation tab in the released position, turn the rotor clockwise, carefully feeling for the ribbon wire to run out of length and a slight resistance is felt. Stop turning at this point.
    4. While holding the anti-rotation tab in the released position, turn the clockspring counterclockwise approximately 2.25 turns. This is the center point of the clockspring.
      • Do not allow the rotor to turn from this position.
        Fig 1: Identifying Anti-Rotation Tab
        G04646697Courtesy of FORD MOTOR CO.

    3. Vehicle repairs reusing the same clockspring 

    NOTE: When the tape is removed, do not allow the clockspring to turn.
  3. Remove the tape applied during clockspring removal.

    4. All vehicles 

    NOTE: Slight turning of the clockspring rotor is allowable for alignment purposes to the steering column.
  4. Install the clockspring.
    1. With the flats of the clockspring aligned to the flats of the steering column, slide the clockspring onto the steering column.
    2. Engage the retaining tabs.
      Fig 2: Identifying Retaining Tabs
      G04646698Courtesy of FORD MOTOR CO.
  5. Install the clockspring wire harness and electrical connectors.
    1. Route the clockspring wire harness down the side of the steering column and install the wire harness retainers.
    2. Connect the clockspring electrical connectors.
      • Install the electrical connectors into the bracket.
        Fig 3: Identifying Electrical Connectors
        G04646699Courtesy of FORD MOTOR CO.
  6. Install the key-in-ignition warning indicator switch.
    Fig 4: Locating Key-In-Ignition Warning Indicator Switch
    G04646700Courtesy of FORD MOTOR CO.

    7. Vehicles with a passive anti-theft system 

  7. Install the passive anti-theft system (PATS) transmitter.
    1. Position the PATS transmitter.
    2. Install the PATS transmitter retaining screw.
      Fig 5: Identifying PATS Transmitter And PATS Transmitter Retaining Screw
      G04646701Courtesy of FORD MOTOR CO.

    8. All vehicles 

  8. Install the upper steering column shroud.
  9. Install the ignition switch lock cylinder.
    • Position the ignition switch lock cylinder to the RUN position.
    • Insert the ignition switch lock cylinder into the steering column.
    • Make sure the ignition switch lock cylinder is fully seated and aligned in the interlocking washer before turning the key to the OFF position.
    • Make sure the ignition switch lock cylinder retaining pin is seated in the hole in the steering column.
    • Rotate the ignition switch lock cylinder through all positions to verify operation.
      Fig 6: Identifying Ignition Switch Lock Cylinder
      G04646702Courtesy of FORD MOTOR CO.
  10. Install the lower steering column shroud and the 3 screws.
  11. Install the steering column opening lower finish panel.
  12. Install the tilt wheel handle and shank.
  13. Install the steering wheel. Do not install the driver air bag module at this time. For additional information, refer to STEERING COLUMN .
  14. Install the driver air bag module. For additional information, refer to DRIVER AIR BAG MODULE .
  15. Repower the system. For additional information, refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
scientia non olet · About LEMON Manuals