LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2000 >> Taurus LX, 3.0 2, AX4N >> Repair and Diagnosis >> External Pages >> Different car >> Section 608 (Engine - 5.4L (3V) - F250 & F350) >> In-Vehicle Repair >> Intake Manifold >> Installation

Intake Manifold: Installation

WARNING: This page is about a different car, the 2006 Ford Pickup and 2006 Ford Cab & Chassis. However, it is still accessible from the selected car via links, so may be relevant.
    NOTE: Electrical and vacuum harnesses must not restrict movement of the CMCV control rods at the rear of the intake manifold. Use extreme care on installation of the intake manifold to prevent any pinching of electrical and vacuum harnesses.
  1. Using new intake manifold gaskets, position the intake manifold.
  2. Using new gaskets, position the coolant crossover and install the 3 bolts
    • Tighten to 10 Nm (89 lb-in).
  3. Install the intake manifold bolts and tighten in 2 stages in the sequence shown.
    • Stage 1: Tighten to 2 Nm (18 lb-in).
    • Stage 2: Tighten to 10 Nm (89 lb-in).
      Fig 1: Identifying Intake Manifold Bolts Tightening Sequence
      G04646849Courtesy of FORD MOTOR CO.
  4. Connect the HO2S electrical connector and attach the electrical connector retainer.
    Fig 2: Locating Electrical Connector Retainer At Coolant Tube Support Bracket
    G03919850Courtesy of FORD MOTOR CO.
  5. Connect the engine wiring harness retainer to the CMCV stud and install the nut.
    • Tighten to 10 Nm (89 lb-in).
  6. Connect the CMCV electrical connector.
  7. Connect the CHT sensor jumper harness electrical connector.
    Fig 3: Locating CHT Sensor Jumper Harness Electrical Connector
    G04646851Courtesy of FORD MOTOR CO.
  8. Connect the LH and RH KS electrical connectors.
    Fig 4: Locating LH And RH KS Electrical Connectors
    G04646852Courtesy of FORD MOTOR CO.
  9. Connect the intake manifold vacuum tube to the support bracket and the valve cover stud.
  10. Connect the brake booster vacuum hose to the intake manifold vacuum tube.
  11. Position the engine wiring harness and connect the wiring harness retainers to the LH valve cover stud bolts.
  12. Connect the LH radio ignition interference capacitor electrical connector.
  13. Connect the LH VCT solenoid electrical connector.
  14. Connect the LH CMP sensor electrical connector.
    Fig 5: Identifying LH CMP Sensor Electrical Connector
    G03919847Courtesy of FORD MOTOR CO.
  15. Connect the EOP sensor electrical connector.
    Fig 6: Identifying Engine Oil Pressure (EOP) Sensor Electrical Connector
    G03919846Courtesy of FORD MOTOR CO.
  16. Connect the 4 LH ignition coil electrical connectors.
    Fig 7: Locating LH Ignition Coil Electrical Connectors
    G04646855Courtesy of FORD MOTOR CO.
  17. Connect the heated PCV intake fitting electrical connector.
    Fig 8: Locating Heated PCV Intake Fitting Electrical Connector
    G04646856Courtesy of FORD MOTOR CO.
  18. Connect the TP sensor and electronic acceleration control electrical connectors.
  19. Connect the 8 fuel injector electrical connectors.
  20. Connect the fuel rail pressure and temperature sensor electrical connector and vacuum connector.
  21. Connect the fuel supply spring lock coupling to the fuel rail. For additional information, refer to FUEL SYSTEM-GENERAL INFORMATION - GASOLINE AND DIESEL .
  22. Position the PCV tube and connect the quick connect couplings. For additional information, refer to FUEL SYSTEM-GENERAL INFORMATION - GASOLINE AND DIESEL .
  23. Connect the EVAP tube quick connect coupling to the intake manifold. For additional information, refer to FUEL SYSTEM-GENERAL INFORMATION - GASOLINE AND DIESEL .
  24. Connect the heater coolant hose to the coolant bypass.
  25. Connect the upper radiator hose to the thermostat housing.
  26. Install the generator. For additional information, refer to GENERATOR AND REGULATOR .
  27. Install the air cleaner. For additional information, refer to INTAKE AIR DISTRIBUTION & FILTERING .
  28. Fill and bleed the engine cooling system. For additional information, refer to ENGINE COOLING .
scientia non olet · About LEMON Manuals