LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2000 >> Taurus LX, 3.0 2, AX4N >> Repair and Diagnosis >> External Pages >> Different car >> Section 1764 (Parking Aid System) >> Diagnosis And Testing >> Parking Aid >> Pinpoint Tests >> Pinpoint Test F: DTC C1742 or DTC C1743 >> Pinpoint Test F: DTC C1742 Or DTC C1743

Pinpoint Test F: DTC C1742 Or DTC C1743

WARNING: This page is about a different car, the 2011 Mercury Milan, 2011 Lincoln MKZ, and 2011 Ford Fusion. However, it is still accessible from the selected car via links, so may be relevant.
NOTE: Use the correct probe adapter(s) when making measurements. Failure to use the correct probe adapter(s) may damage the connector.
  1. F1 CHECK THE DTCs FROM THE PAM SELF-TESTS 
    • Ignition ON.
    • Retrieve the PAM DTCs from the continuous and on-demand self-tests.
    • Are parking aid DTCs other than C1742 or C1743 present? 
    1. Yes  : Diagnose other DTCs first. REFER to DTC CHARTS  in this service information.
    2. No  : GO to F2.
  2. F2 MEASURE THE PARKING AID SPEAKER RESISTANCE 
    • Disconnect: Parking Aid Speaker C4015.
    • Measure the resistance between the parking aid speaker pin 1, component side and the parking aid speaker pin 2, component side.
      Fig 1: Measuring Resistance Between Parking Aid Speaker Pin 2 And Parking Aid Speaker Pin 1
      G07787374Courtesy of FORD MOTOR CO.
    • Is the resistance between 40 and 60 ohms? 
    1. Yes  : If DTC C1742 was recorded, GO to F3.

      If DTC C1743 was recorded, GO to  F7.

    2. No  : INSTALL a new parking aid speaker. REFER to PARKING AID SPEAKER  in this service information. CLEAR the DTCs. REPEAT the self-test.
  3. F3 CHECK THE PARKING AID SPEAKER (+) CIRCUIT FOR A SHORT TO GROUND 
    • Connect: Parking Aid Speaker C4015.
    • Disconnect: PAM C4014.
    • Measure the resistance between the PAM C4014-2, circuit CMP09 (BN/BU), harness side and ground.
      Fig 2: Measuring Resistance Between PAM C4014-2, Circuit CMP09 (BN/BU), Harness Side And Ground
      G07787375Courtesy of FORD MOTOR CO.
    • Is the resistance greater than 10,000 ohms? 
    1. Yes  : GO to  F5.
    2. No  : GO to F4.
  4. F4 CHECK THE PARKING AID SPEAKER (+) CIRCUIT FOR A SHORT TO GROUND WITH THE PARKING AID SPEAKER DISCONNECTED 
    • Disconnect: Parking Aid Speaker C4015.
    • Measure the resistance between the PAM C4014-2, circuit CMP09 (BN/BU), harness side and ground.
      Fig 3: Measuring Resistance Between PAM C4014-2, Circuit CMP09 (BN/BU), Harness Side And Ground
      G07787376Courtesy of FORD MOTOR CO.
    • Is the resistance greater than 10,000 ohms? 
    1. Yes  : REPAIR circuit RMP09 (BU/GN). CLEAR the DTCs. TEST the system for normal operation.
    2. No  : REPAIR circuit CMP09 (BN/BU). CLEAR the DTCs. TEST the system for normal operation.
  5. F5 CHECK THE PARKING AID SPEAKER (+) CIRCUIT FOR AN OPEN 
    • Disconnect: Parking Aid Speaker C4015.
    • Measure the resistance between the PAM C4014-2, circuit CMP09 (BN/BU), harness side and the parking aid speaker C4015-2, circuit CMP09 (BN/BU), harness side.
      Fig 4: Measuring Resistance Between PAM C4014-2, Circuit CMP09 (BN/BU), Harness Side And Parking Aid Speaker C4015-2, Circuit CMP09 (BN/BU)
      G07787377Courtesy of FORD MOTOR CO.
    • Is the resistance less than 5 ohms? 
    1. Yes  : GO to F6.
    2. No  : REPAIR the circuit. CLEAR the DTCs. TEST the system for normal operation.
  6. F6 CHECK THE PARKING AID SPEAKER (-) CIRCUIT FOR AN OPEN 
    • Measure the resistance between the PAM C4014-6, circuit RMP09 (BU/GN), harness side and the parking aid speaker C4015-1, circuit RMP09 (BU/GN), harness side.
      Fig 5: Measuring Resistance Between PAM C4014-6, Circuit RMP09 (BU/GN), Harness Side And Parking Aid Speaker C4015-1, Circuit RMP09 (BU/GN)
      G07787378Courtesy of FORD MOTOR CO.
    • Is the resistance less than 5 ohms? 
    1. Yes  : GO to  F8.
    2. No  : REPAIR the circuit in question. CLEAR the DTCs. TEST the system for normal operation.
  7. F7 CHECK THE PARKING AID SPEAKER CIRCUITRY FOR SHORTS TO VOLTAGE 
    • Ignition ON.
    • Measure the voltage between the PAM C4014-2, circuit CMP09 (BN/ BU), harness side and ground; and between the PAM C4014-6, circuit RMP09 (BU/GN), harness side and ground.
      Fig 6: Measuring Voltage Between PAM C4014-2, Circuit CMP09 (BN/BU), Harness Side And Ground And Between PAM C4014-6, Circuit RMP09 (BU/GN), Harness Side And Ground
      G07787379Courtesy of FORD MOTOR CO.
    • Is any voltage present? 
    1. Yes  : REPAIR the circuit in question. CLEAR the DTCs. TEST the system for normal operation.
    2. No  : GO to F8.
  8. F8 CHECK FOR CORRECT PAM OPERATION 
    • Disconnect the PAM connector.
    • Check for:
      • corrosion
      • damaged pins
      • pushed-out pins
    • Connect the PAM connector and make sure it seats correctly.
    • Operate the system and determine if the concern is still present.
    • Is the concern still present? 
    1. Yes  : INSTALL a new PAM. REFER to PARKING AID MODULE (PAM)  in this service information. CLEAR the DTCs. REPEAT the self-test. CARRY OUT the scan tool data link test.
    2. No  : The system is operating correctly at this time. The concern may have been caused by a loose or corroded connector. CLEAR the DTCs. REPEAT the self-test.
scientia non olet · About LEMON Manuals