LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2000 >> Taurus LX, 3.0 2, AX4N >> Repair and Diagnosis >> External Pages >> Different car >> Section 165 (Instrument Panel And Console -- F250-F550 Super Duty) >> Removal And Installation >> Instrument Panel >> Installation

Instrument Panel: Installation

WARNING: This page is about a different car, the 2005 Ford Pickup, 2005 Ford F550 Super Duty, 2005 Ford F450 Super Duty, and 2005 Ford Cab & Chassis. However, it is still accessible from the selected car via links, so may be relevant.
    NOTE: This step requires an assistant.
  1. Install the instrument panel.
  2. Install the LH instrument panel cowl side bolts.
    Fig 1: LH Instrument Panel Cowl Side Bolts -- With Torque Specifications
    G03911695Courtesy of FORD MOTOR CO.
  3. Install the lower RH instrument panel cowl side bolt.
    Fig 2: RH Instrument Panel Cowl Side Bolt -- With Torque Specifications
    G03911696Courtesy of FORD MOTOR CO.
  4. Install the upper RH instrument panel cowl side bolt.
    Fig 3: Upper RH Instrument Panel Cowl Side Bolt -- With Torque Specifications
    G03911697Courtesy of FORD MOTOR CO.
  5. Install the LH instrument panel center support bolt.
    Fig 4: LH Instrument Panel Center Support Bolt -- With Torque Specifications
    G03911698Courtesy of FORD MOTOR CO.
  6. Install the LH instrument panel end finish panel.
    Fig 5: Installing LH Instrument Panel End Finish Panel
    G03911690Courtesy of FORD MOTOR CO.
  7. Install the instrument panel cowl top bolts.
    1. Install the bolts.
    2. Install the cowl top attaching bolt covers.
      Fig 6: Installing Instrument Panel Cowl Top Bolts - With Torque Specifications
      G03911700Courtesy of FORD MOTOR CO.
  8. Install the autolamp sunload sensor finish panel.
    • Connect the electrical connector.
      Fig 7: Locating Autolamp Sunload Sensor Finish Panel
      G03911688Courtesy of FORD MOTOR CO.
  9. Install the RH cowl side bolt cover.
    Fig 8: Installing RH Cowl Side Bolt Cover
    G03911687Courtesy of FORD MOTOR CO.
  10. Install the RH ground bolt.
    Fig 9: RH Ground Bolt -- With Torque Specifications
    G03925831Courtesy of FORD MOTOR CO.
  11. Connect the RH cowl side electrical connectors.
    Fig 10: Locating RH Cowl Side Electrical Connectors
    G03911685Courtesy of FORD MOTOR CO.
  12. Lower the glove compartment.
    1. Open the glove compartment.
    2. While releasing the glove compartment stops, lower the glove compartment.
      Fig 11: Lowering Glove Compartment
      G03911681Courtesy of FORD MOTOR CO.
  13. Connect the climate control vacuum harness connector.
    Fig 12: Identifying Climate Control Vacuum Harness Connector
    G03911683Courtesy of FORD MOTOR CO.
  14. Connect the blend door actuator electrical connector.
    Fig 13: Identifying Blend Door Actuator Electrical Connector
    G03911682Courtesy of FORD MOTOR CO.
  15. Close the glove compartment.
    1. Depress the glove compartment stops.
    2. Close the glove compartment.
      Fig 14: Closing Glove Compartment
      G03911684Courtesy of FORD MOTOR CO.
  16. Connect the ECS module electrical connector.
    1. Connect the ECS module electrical connector.
    2. Install the locking clip.
      Fig 15: Connecting ECS Module Electrical Connector
      G03911709Courtesy of FORD MOTOR CO.
  17. Install the ECS module cover.
    Fig 16: Locating ECS Module Cover
    G03911679Courtesy of FORD MOTOR CO.
  18. If equipped, connect the transmission shift cable to the steering column.
    1. Connect the cable to the steering column bracket.
    2. Connect the cable to the steering column shift lever.
      Fig 17: Connecting Transmission Shift Cable To Steering Column
      G03911711Courtesy of FORD MOTOR CO.
  19. Connect the intermediate shaft to the steering column.
    1. Connect the intermediate shaft to the steering column.
    2. Install the steering column shaft pinch bolt.
      Fig 18: Connecting Intermediate Shaft To Steering Column - With Torque Specifications
      G03911712Courtesy of FORD MOTOR CO.
  20. If equipped, connect the adjustable pedal motor harness electrical connector.
    Fig 19: Locating Adjustable Pedal Motor Harness Electrical Connector
    G03911676Courtesy of FORD MOTOR CO.
  21. If equipped, connect the adjustable pedal motor electrical connector.
    Fig 20: Locating Adjustable Pedal Motor Electrical Connector
    G03911675Courtesy of FORD MOTOR CO.
  22. Through the steering column opening, connect the wiring harness electrical connector.
    Fig 21: Locating Wiring Harness Electrical Connector
    G03911715Courtesy of FORD MOTOR CO.
  23. If equipped, connect the CPP switch electrical connector.
    Fig 22: Connecting CPP Switch Electrical Connector
    G03925801Courtesy of FORD MOTOR CO.
  24. Connect the BPP switch electrical connector.
    Fig 23: Connecting BPP Switch Electrical Connector
    G03911673Courtesy of FORD MOTOR CO.
  25. Connect the parking brake switch electrical connector.
    Fig 24: Connecting Parking Brake Switch Electrical Connector
    G03911672Courtesy of FORD MOTOR CO.
  26. Position the CJB aside.
    1. Release the tab.
      Fig 25: Releasing Tab
      G03911671Courtesy of FORD MOTOR CO.
  27. Install the parking brake release handle.
    1. Position the parking brake release handle.
    2. Install the nuts.
      Fig 26: Installing Parking Brake Release Handle - With Torque Specifications
      G03911719Courtesy of FORD MOTOR CO.
  28. Connect the in-line electrical connector.
    Fig 27: Locating In-Line Electrical Connector
    G03911669Courtesy of FORD MOTOR CO.
  29. Connect the CJB electrical connectors.
    Fig 28: Locating CJB Electrical Connectors
    G03911668Courtesy of FORD MOTOR CO.
  30. Install the CJB.
    1. Connect the tab.
    2. Install the bolt.
      Fig 29: Installing CJB - With Torque Specifications
      G03911722Courtesy of FORD MOTOR CO.
  31. Install the instrument panel steering column cover.
    • Position the instrument panel steering column cover by positioning lower hooks into slots at bottom of instrument panel.
    • Push retainer clips into the instrument panel.
      Fig 30: Installing Instrument Panel Steering Column Cover
      G03925852Courtesy of FORD MOTOR CO.
  32. Route the antenna cable into the inner fender opening.
    1. Route the antenna cable into the inner fender opening.
    2. Seat the antenna cable grommet into the dash panel.
      Fig 31: Routing Antenna Cable Into Inner Fender Opening
      G03911724Courtesy of FORD MOTOR CO.
  33. Install the RH front fender splash shield.
    1. Position the front fender splash shield.
    2. Install the pin-type retainers.
    3. Install the screws.
    4. Install the three nuts.
      Fig 32: Installing RH Front Fender Splash Shield
      G03911725Courtesy of FORD MOTOR CO.
  34. Install the antenna base. For additional information, refer to ANTENNA .
  35. Install the LH and RH front door weatherstrips.
    Fig 33: Identifying Front Door Weatherstrips
    G03911663Courtesy of FORD MOTOR CO.
  36. Install the LH and RH A-pillar lower trim panels.
    1. Position the A-pillar lower trim panels.
    2. Install the pin-type retainers.
      Fig 34: Installing A-Pillar Lower Trim Panels
      G03911727Courtesy of FORD MOTOR CO.
  37. Install the LH and RH scuff plates.
  38. If equipped with a manual transmission, install the upper gearshift lever.
    • Install the bolts.
      Fig 35: Installing Upper Gearshift Lever Bolts - With Torque Specifications
      G03923392Courtesy of FORD MOTOR CO.
  39. If equipped with manual transmission, install the shift lever boot.
    • Install the screws.
      Fig 36: Identifying Gear Shift Lever Boot Screws
      G03923381Courtesy of FORD MOTOR CO.
  40. Feed the wiring harness into the engine compartment and connect the electrical connectors.
    Fig 37: Connecting Electrical Connectors
    G03911658Courtesy of FORD MOTOR CO.
  41. Connect the CJB cable at the junction block.
    • Feed the cable into the engine compartment and install the wiring harness grommet.
    • Install the nut.
      Fig 38: Installing Cable Nut
      G03911659Courtesy of FORD MOTOR CO.
  42. Clip the instrument panel harness locator into the pedal bracket.
    Fig 39: Clipping Instrument Panel Harness Locator Into Pedal Bracket
    G03911660Courtesy of FORD MOTOR CO.
  43. Clip the harness locator to the PCM bracket.
    Fig 40: Clipping Harness Locator To PCM Bracket
    G03911661Courtesy of FORD MOTOR CO.
  44. Repower the supplemental restraint system (SRS). For additional information, refer to Supplemental Restraint System (SRS) Depowering and Repowering in SUPPLEMENTAL RESTRAINT SYSTEM .
scientia non olet · About LEMON Manuals