LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2000 >> Taurus LX, 3.0 2, AX4N >> Repair and Diagnosis >> External Pages >> Different car >> Section 1599 (Automatic Transmission - Automatic Transaxle/Transmission - 4R70E/4R75E) >> In-Vehicle Servicing >> Manual Control Lever Shaft and Seal >> Installation

Manual Control Lever Shaft and Seal: Installation

WARNING: This page is about a different car, the 2010 Lincoln Town Car. However, it is still accessible from the selected car via links, so may be relevant.
  1. Using the special tool, install the manual control lever shaft seal.
    2. Fig 1: Installing Manual Control Lever Shaft Seal
    GF0012362Courtesy of FORD MOTOR CO.
  2. Install the manual control lever shaft.
    1. Install the manual control lever shaft.
    2. Install the manual control lever nut.
      • Tighten to 32 Nm (24 lb-ft).
    3. Install the manual control lever shaft retaining pin.
    3. Fig 2: Installing Manual Control Lever Shaft
    GF0014073Courtesy of FORD MOTOR CO.
  3. Install the manual valve detent lever spring and bolt.
    • Tighten to 10 Nm (89 lb-in).
    4. Fig 3: Locating Manual Valve Detent Lever Spring & Bolt
    G04584283Courtesy of FORD MOTOR CO.
    CAUTION: If installing a new transmission fluid filter and the seal remains in the main control bore, carefully use a small screwdriver to remove the seal. Use care not to damage the main control bore.
    NOTE: If transmission is being serviced for a contamination-related failure, use a new transmission fluid filter and seal. The transmission fluid filter may be reused if no excessive contamination is present.
  4. Install a new transmission fluid filter and seal as required.
    5. Fig 4: Installing A New Transmission Fluid Filter And Seal
    GF0003479Courtesy of FORD MOTOR CO.
  5. Position the magnet into the transmission fluid pan.
    6. Fig 5: Locating Pan Magnet In Transmission Fluid Pan
    G03888537Courtesy of FORD MOTOR CO.
    NOTE: The transmission fluid pan gasket is reusable, clean and inspect for damage, if not damaged, the transmission fluid pan gasket should be reused.
  6. Install the transmission fluid pan and transmission fluid pan gasket.
    1. Position the transmission fluid pan and transmission fluid pan gasket in place.
    2. Install the transmission fluid pan bolts.
      • Tighten to 14 Nm (10 lb-ft).
    7. Fig 6: Transmission Fluid Pan & Bolts
    GF0014074Courtesy of FORD MOTOR CO.
  7. Install the digital TR sensor and loosely install the bolts.
    8. Fig 7: Identifying Digital TR Sensor And Bolts
    G04584370Courtesy of FORD MOTOR CO.
    NOTE: Manual control lever must be in the NEUTRAL position.
  8. Using the special tool, align the digital TR sensor slots. The tool is designed to fit snugly.
    9. Fig 8: Aligning Digital TR Sensor Slots Using Special Tool (307-351)
    G04584268Courtesy of FORD MOTOR CO.
    CAUTION: Tightening one screw before tightening the other may cause the sensor to bind or become damaged.
  9. Tighten the screws in an alternating sequence.
    • Tighten to 9 Nm (80 lb-in).
    10. Fig 9: Aligning Digital TR Sensor Slots With Special Tool
    G04584269Courtesy of FORD MOTOR CO.
  10. With the manual lever in overdrive, connect the selector lever cable.
    • Tighten to 30 Nm (22 lb-ft).
    11. Fig 10: Selector Lever Cable At Transmission
    GF0014071Courtesy of FORD MOTOR CO.
  11. Connect the digital TR sensor electrical connector.
    12. Fig 11: Transmission Range (TR) Sensor Electrical Connector
    GF0014070Courtesy of FORD MOTOR CO.
    NOTE: Start by filling the transmission with 4.7L (5 qt) of clean transmission fluid.
  12. Fill the transmission to the correct fluid level, using clean transmission fluid.
scientia non olet · About LEMON Manuals