LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2000 >> Taurus LX, 3.0 2, AX4N >> Repair and Diagnosis >> External Pages >> Different car >> Section 137 (Engine - 6.8L (3V) -- F250-F550 Super Duty) >> In-Vehicle Repair >> Valve Cover - RH >> Removal

Valve Cover - RH: Removal

WARNING: This page is about a different car, the 2005 Ford Pickup, 2005 Ford F550 Super Duty, 2005 Ford F450 Super Duty, and 2005 Ford Cab & Chassis. However, it is still accessible from the selected car via links, so may be relevant.
  1. Remove the RH ignition coils. For additional information, refer to ENGINE IGNITION - 5.4L AND 6.8L (3V) .
  2. If equipped, remove the automatic transmission filler tube. For additional information, refer to AUTOMATIC TRANSAXLE/TRANSMISSION - TORQSHIFT .
  3. Remove the throttle body adapter. For additional information, refer to FUEL CHARGING AND CONTROLS - 6.8L (3V) .
  4. Remove the generator. For additional information, refer to GENERATOR AND REGULATOR .
  5. Remove the cooling fan shroud. For additional information, refer to ENGINE COOLING .
  6. Install the special tools.
    Fig 1: Installing Special Tools
    G04647876Courtesy of FORD MOTOR CO.
    7. CAUTION: Only use hand tools when removing the transmission mount-to-crossmember nuts or damage to the transmission mount can occur.
    Fig 2: Identifying Transmission Mount-To-Crossmember Nuts
    G03963913Courtesy of FORD MOTOR CO.
  7. Loosen the transmission mount-to-crossmember nuts.
    8. CAUTION: Only use hand tools when installing the RH engine mount nut or damage to the engine mount can occur.
    NOTE: RH shown, LH similar.
    Fig 3: Identifying Engine Mount Nuts
    G03920590Courtesy of FORD MOTOR CO.
  8. Remove the 3 RH engine mount nuts and loosen the 3 LH engine mount nuts.
  9. Remove the 4 exhaust manifold-to-catalytic converter nuts.
    Fig 4: Locating Exhaust Manifold-To-Catalytic Converter Nuts
    G03920889Courtesy of FORD MOTOR CO.
  10. Disconnect the quick connect couplings and remove the evaporative emissions (EVAP) tube. For additional information, refer to FUEL SYSTEM-GENERAL INFORMATION - GASOLINE AND DIESEL .
    Fig 5: Disconnecting Quick Connect Couplings
    G03920575Courtesy of FORD MOTOR CO.
  11. Disconnect the engine wiring harness retainers from the valve cover and position out of the way.
    Fig 6: Disconnecting Engine Wiring Harness Retainers From Valve Cover
    G03920593Courtesy of FORD MOTOR CO.
  12. Disconnect the quick connect coupling and remove the positive crankcase ventilation (PCV) tube from the valve cover. For additional information, refer to FUEL SYSTEM-GENERAL INFORMATION - GASOLINE AND DIESEL .
  13. Using the special tools, raise the engine.
    Fig 7: Installing Special Tools
    G04647876Courtesy of FORD MOTOR CO.
    14. CAUTION: Do not use metal scrapers, wire brushes, power abrasive discs or other abrasive means to clean the sealing surfaces. These tools cause scratches and gouges which make leak paths. Use a plastic scraping tool to remove all traces of old sealant.
    NOTE: The bolts are part of the valve cover and should not be removed.
  14. Loosen the 16 fasteners in the sequence shown and remove the RH valve cover and gasket.
    • Clean the valve cover mating surface of the cylinder head with silicone gasket remover and metal surface prep. Follow the directions on the packaging.
    • Discard the valve cover gasket. Clean the valve cover gasket groove with soap and water or a suitable solvent.
      Fig 8: Identifying Valve Cover Tightening Sequence
      G03920595Courtesy of FORD MOTOR CO.
scientia non olet · About LEMON Manuals