LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2000 >> Mustang Base, 2D Convertible, Standard >> Repair and Diagnosis >> External Pages >> Different car >> Section 1792 (Wheel Hubs & Bearings - Full Floating Axle - Ford -- F250-F350 Super Duty) >> Removal And Installation >> Wheel Hub >> Removal

Wheel Hub: Removal

WARNING: This page is about a different car, the 2007 Ford Pickup and 2007 Ford Cab & Chassis. However, it is still accessible from the selected car via links, so may be relevant.
  1. Set the parking brake.
  2. Loosen the axle shaft bolts.
    3. Fig 1: Locating Axle Shaft Bolts
    GF0006576Courtesy of FORD MOTOR CO.
  3. Raise the vehicle to the desired working height, keeping the axle parallel with the floor. For additional information, refer to JACKING AND LIFTING article.
  4. Release the parking brake.
  5. Remove the wheel(s). For additional information, refer to WHEELS AND TIRES article.
  6. Remove the brake caliper and brake disc on the single rear wheel axle. For additional information, refer to REAR DISC BRAKE article.
  7. Remove the axle shaft bolts and axle shaft.
    8. Fig 2: Locating Axle Shaft Bolts And Axle Shaft
    GF0006600Courtesy of FORD MOTOR CO.
    CAUTION: The hub nuts are right-hand thread (right hub) and left-hand thread (left hub). Each hub nut is stamped RH or LH.
  8. Install the Ford Axle Locknut Socket so that the drive tangs of the tool engage the 4 slots in the hub nut.
    9. Fig 3: Identifying Ford Axle Locknut Socket
    GF0006601Courtesy of FORD MOTOR CO.
    CAUTION: Discard the hub nut if the hub nut comes apart during removal.
    CAUTION: Under no circumstances are power tools to be used when carrying out these operations.
    NOTE: The hub nut will ratchet during this operation.
  9. Remove the hub nut (counterclockwise for right-hand thread; clockwise for left-hand thread).
    10. Fig 4: Locating Hub Nut
    GF0006602Courtesy of FORD MOTOR CO.
  10. Install the Step Plate.
    11. Fig 5: Locating Step Plate
    GF0006603Courtesy of FORD MOTOR CO.
  11. Using a suitable 2-Jaw Puller, loosen the rear hub to the point of removal.
    12. Fig 6: Using A Suitable 2-Jaw Puller Loosen Rear Hub
    GF0006604Courtesy of FORD MOTOR CO.
    CAUTION: Do not drop the outer hub bearing when removing the hub.
  12. Remove the rear hub assembly.
    13. Fig 7: Locating Rear Hub Assembly
    GF0006605Courtesy of FORD MOTOR CO.
    CAUTION: Install a new hub seal each time the hub assembly is removed.
    NOTE: The inner bearing is located behind the hub seal.
  13. Pack each bearing and install new hub seals. For additional information, refer to Wheel Bearings, Wheel Hub Seal and Wheel Bearing Cups  in this article.
    14. CAUTION: Use extreme care not to scratch or gouge the seal or bearing surfaces.
  14. If after hub removal, the hub seal or seal inner sleeve remains on the spindle, remove it as shown using the Step Plate and the 2-Jaw Puller.
    15. Fig 8: Locating Hub Seal Or Seal Inner Sleeve Remains On Spindle
    GF0006606Courtesy of FORD MOTOR CO.
  15. Inspect the seal surface and inner shoulder for scratches and damage.
    • Remove all scratches, gouges or galling damage with No. 600 or finer crocus cloth.
Fig 9: Removing Scratches, Gouges Or Galling Damage With No. 600 Or Finer Crocus Cloth
GF0006607Courtesy of FORD MOTOR CO.
scientia non olet · About LEMON Manuals