Torque Specifications
WARNING: This page is about a different car, the 2007 Ford Pickup, 2007 Ford F550 Super Duty, 2007 Ford F450 Super Duty, and 2007 Ford Cab & Chassis. However, it is still accessible from the selected car via links, so may be relevant.
TORQUE SPECIFICATIONS
| Description | Nm | lb-ft | lb-in |
|---|---|---|---|
| A/C hose nut | 8 | - | 71 |
| A/C compressor bolts | 25 | 18 | - |
| Accessory drive belt idler pulley bolts | 47 | 35 | - |
| Accessory drive belt pulley bracket bolts | 25 | 18 | - |
| Accessory drive belt tensioner bolts | 25 | 18 | - |
| Air inlet duct clamp | 5 | - | 44 |
| Automatic transmission tube nut | 8 | - | 71 |
| Battery crossover cable nut | 8 | - | 71 |
| Battery cable nut | 12 | 9 | - |
| Battery ground cable-to-engine block bolts | 47 | 35 | - |
| Battery tray bolts | 16 | 12 | - |
| Battery cable bracket nut | 47 | 35 | - |
| Block heater | 41 | 30 | - |
| Coolant pump bolts | 23 | 17 | - |
| Coolant pump pulley bolts | 31 | 23 | - |
| Cooling fan stator bolts | 40 | 30 | - |
| Crankcase-to-head tube | 82 | 60 | - |
| Crankshaft pulley bolts (dual generators) | 47 | 35 | - |
| Cylinder block coolant drain pluga | 20 | 15 | - |
| Charge air cooler (CAC) duct clamps (metal duct) | 12 | 9 | - |
| CAC duct clamps (blow molded duct) | 12 | 9 | - |
| Connecting rod bearing cap boltsb | - | - | - |
| Crankcase breather screws | 7 | - | 62 |
| Cylinder head boltsb | - | - | - |
| Cam follower mounting bolt | 13 | 10 | - |
| Camshaft thrust plate-mounting bolts | 31 | 23 | - |
| Coolant pump mounting bolts | 23 | 17 | - |
| Crankshaft position (CKP) sensor | 13 | 10 | - |
| Camshaft position (CMP) sensor | 13 | 10 | - |
| Exhaust tube-to-exhaust manifold flange bolts (left side)c | 27 | 20 | - |
| Exhaust tube-to-exhaust manifold flange bolts (right side)c | 27 | 20 | - |
| Exhaust manifold flange boltsc | 38 | 28 | - |
| Exhaust pipe retaining nuts | 47 | 35 | - |
| Exhaust gas recirculation (EGR) valve mounting bolts | 13 | 10 | - |
| EGR clamp, V-band | 6 | - | 53 |
| EGR cooler bolts (M6 x 16) | 13 | 10 | - |
| EGR cooler stud bolts (M6 x 55 x 20) | 13 | 10 | - |
| EGR cooler coolant supply port cover (M6) | 10 | - | 89 |
| Engine bracket-to-cylinder block bolts | 62 | 46 | - |
| Engine coolant temperature (ECT) sensor | 18 | 13 | - |
| Engine oil temperature (EOT) sensor | 18 | 13 | - |
| Engine mount-to-engine bracket | 62 | 46 | - |
| Engine mount nuts | 103 | 76 | - |
| Exhaust pressure (EP) sensor tube assembly | 30 | 22 | - |
| EP sensor | 20 | 15 | - |
| EP sensor bracket nut | 13 | 10 | - |
| Engine ground strap bolt | 10 | - | 89 |
| Flywheel/flexplate mounting boltsb | - | - | - |
| Front, lifting eye (M10 x 30) | 41 | 30 | - |
| Fan clutch hub-to-coolant pump | 133 | 98 | - |
| Fuel tube banjo fittingsb | - | - | - |
| Fuel injector hold-down bolt | 35 | 26 | - |
| Fuel injector control module (FICM) nuts and bolts | 13 | 10 | - |
| FICM bracket nuts | 8 | - | 71 |
| Fuel tube bracket bolt | 13 | 10 | - |
| Front engine cover bolts | 24 | 18 | - |
| Fuel filter plug assembly (back of head) | 27 | 20 | - |
| Gerotar cover bolt | 13 | 10 | - |
| Glow plug | 19 | 14 | - |
| Generator B+ wire nut | 8 | - | 71 |
| Glow plug module mounting bracket nuts | 9 | - | 80 |
| Generator mounting bracket bolts (dual Generators) | 47 | 35 | - |
| Glow plug module | 8 | - | 71 |
| Heater hose tube | 13 | 10 | - |
| High pressure oil pump cover bolts | 11 | 8 | - |
| High pressure oil pump mounting bolts | 31 | 23 | - |
| High pressure oil pump discharge tube mounting bolts | 11 | 8 | - |
| Injection control pressure (ICP) sensor | 12 | 9 | - |
| Injection pressure regulator (IPR) valve | 50 | 37 | - |
| Intake manifold boltsb | - | - | - |
| Intake air temperature 2 (IAT2) sensor | 18 | 13 | - |
| Lower crankcase main bearing cap boltsb | - | - | - |
| Lower crankcase outer bolts (M8 x 30) | 31 | 23 | - |
| Oil cooler mounting bolts (6 mm) | 10 | - | 89 |
| Oil cooler mounting bolts (8 mm) | 22 | 16 | - |
| Oil filter housing bolts (Torx) | 15 | 11 | - |
| Oil filter return tube bolt, new base | 6 | - | 53 |
| Oil filter return tube bolt, re-installation | 3 | - | 27 |
| Oil drain pan plug | 44 | 32 | - |
| Oil pickup tube flange bolts | 13 | 10 | - |
| Oil pan bolt - lower | 13 | 10 | - |
| Oil pan bolts - upper | 13 | 10 | - |
| Oil rail assemblyb | - | - | - |
| Piston cooling jet mounting boltd | 13 | 10 | - |
| Power steering cooler bolts | 11 | 8 | - |
| Power steering pump bolt | 25 | 18 | - |
| Rocker arm assembly bolts | 31 | 23 | - |
| Right and left head supply tubes at filter | 26 | 19 | - |
| Rear engine cover bolts | 24 | 18 | - |
| Rear engine tube assembly bolts | 13 | 10 | - |
| Rear, lifting eye (M10 x 35) | 41 | 30 | - |
| Rocker arm carrier bolts | 62 | 46 | - |
| Starter positive cable nut | 12 | 9 | - |
| Starter control wire nut | 6 | - | 53 |
| Starter mounting boltsb | 25 | 18 | - |
| Turbocharger flange-to-exhaust gas recirculation (EGR) tube bolts (right side)c | 27 | 20 | - |
| Turbocharger mounting bolts | 31 | 23 | - |
| Turbocharger pedestal bolts | 31 | 23 | - |
| Turbocharger oil supply tube bolts (at turbocharger) | 23 | 17 | - |
| Turbocharger oil supply tube bolt (at oil cooler) | 10 | - | 89 |
| Turbocharger heat shield bolts (M6 x 1.0 x 1.2) | 11 | 8 | - |
| Turbocharger heat shield bolt (M10 x 1.5 x 16) | 49 | 36 | - |
| Torque converter nut | 35 | 26 | - |
| Turbocharger adapter pipe nuts | 40 | 30 | - |
| Transmission-to-engine bolts | 47 | 35 | - |
| Transmission tubes mounting bracket bolts | 10 | - | 89 |
| Transmission cooler bolts | 8 | - | 71 |
| Turbocharger adapter pipe-to-exhaust manifold bolts | 27 | 20 | - |
| Thermostat housing retaining bolts | 23 | 17 | - |
| Upper radiator support bolts | 12 | 9 | - |
| Vibration damper mounting boltsb | - | - | - |
| Valve cover bolts and studs | 9 | - | 80 |
a Apply clean engine oil the O-ring seal before installing.
b Refer to the procedure.
c Apply High Temperature Nickel Anti-Seize Lubricant (XL-2) to the threads prior to assembly.
d Apply Threadlock 262 to bolt threads prior to assembly.