LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2000 >> Excursion 5.4 L, RWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 923 (Engine - 6.0L Diesel -- F250-F550 Super Duty 6.0L (99P F450/550)) >> In-Vehicle Servicing >> Engine Mount - LH >> All vehicles

All vehicles

WARNING: This page is about a different car, the 2007 Ford Pickup, 2007 Ford F550 Super Duty, 2007 Ford F450 Super Duty, and 2007 Ford Cab & Chassis. However, it is still accessible from the selected car via links, so may be relevant.
  1. Remove the cooling fan stator. For additional information, refer to ENGINE COOLING article.
  2. Disconnect the LH and RH battery ground cables. For additional information, refer to BATTERY, MOUNTING AND CABLES article.
    3. Fig 1: Charge-Air-Cooler (CAC) Clamp
    GF0005697Courtesy of FORD MOTOR CO.
  3. Loosen the clamp at the charge-air-cooler (CAC).
    • To install, tighten to 12 Nm (9 lb-ft).
    4. Fig 2: Charge-Air-Cooler (CAC) Clamp At Turbocharger
    GF0005698Courtesy of FORD MOTOR CO.
    NOTE: If there is any oil residue, clean both connecting ports and the inside surface of the CAC duct to prevent the duct from blowing off.
  4. Loosen the clamp at the turbocharger and remove the CAC duct.
    • To install, tighten to 12 Nm (9 lb-ft).
    5. Fig 3: Charge-Air-Cooler (CAC) Clamp At Engine
    GF0005778Courtesy of FORD MOTOR CO.
    NOTE: If there is any oil residue, clean both connecting ports and the inside surface of the CAC duct to prevent the duct from blowing off.
  5. Loosen the clamp and disconnect the CAC duct at the engine.
    • To install, tighten to 12 Nm (9 lb-ft).
    6. Fig 4: Charge-Air-Cooler (CAC) Clamp At Duct
    GF0005779Courtesy of FORD MOTOR CO.
  6. Loosen the clamp and remove the CAC duct.
    • To install, tighten to 12 Nm (9 lb-ft).
    7. Fig 5: Locating Engine Mount Retaining Nuts
    G03921670Courtesy of FORD MOTOR CO.
    NOTE: RH shown, LH similar.
  7. Remove the 4 RH and the 4 LH motor mount nuts.
    • To install, tighten to 103 Nm (76 lb-ft).


Fig 1: Locating Generator Bolts
G03907094Courtesy of FORD MOTOR CO.
  1. Remove the bolts and position the generator back.
    • To install, tighten to 47 Nm (35 lb-ft).
    2. Fig 2: Locating Hood Lift Assembly
    G03907095Courtesy of FORD MOTOR CO.
  2. Support the hood and disconnect the hood lift assemblies.
    3. Fig 3: 2 Lifting Eyes On Right Cylinder Head
    GF0005761Courtesy of FORD MOTOR CO.
  3. Install 2 lifting eyes on the RH cylinder head.
    4. Fig 4: Fuel Tube Bracket Bolt
    GF0005762Courtesy of FORD MOTOR CO.
  4. Remove the retaining bolts for the fuel lines.
    5. Fig 5: Identifying Clamp And Heater Hose
    G03921453Courtesy of FORD MOTOR CO.
  5. Disconnect the heater hose at the front cover.
    6. Fig 6: Lifting Eye On Left Cylinder Head
    GF0005763Courtesy of FORD MOTOR CO.
  6. Install one lifting eye on the LH cylinder head.
    7. Fig 7: Special Tool
    GF0005764Courtesy of FORD MOTOR CO.
    CAUTION: Do not use the special tool to raise the engine. Damage to the special tool or vehicle may occur.
    NOTE: The ball studs may have to be removed.
    NOTE: This procedure requires a second bolt hook assembly. The tools are available through Rotunda Tools with the following numbers: bolt hook 303-F070-6, handle 303-F070-8, bracket 303-F070-7 and washer 303-F070-12004.
  7. Install the special tool.
    8. NOTE: The engine must be raised evenly.
  8. Using a lifting crane, raise the engine until the turbocharger is almost touching the cowl. Secure the engine with the special tool.
  9. Remove the 4 engine mount-to-engine mount bracket bolts.
    • To install, tighten to 62 Nm (46 lb-ft).
  10. Remove the 4 engine mount bracket-to-cylinder block bolts, the engine mount bracket and the engine mount.
    • To install, tighten to 62 Nm (46 lb-ft).
  11. To install, reverse the removal procedure.
scientia non olet · About LEMON Manuals