LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2000 >> Contour SE, 2.5 L, Standard >> Repair and Diagnosis >> External Pages >> Different car >> Section 957 (Seat System -- F250-F550 Super Duty) >> Diagnosis And Testing >> Seats >> Pinpoint Tests >> Pinpoint Test E: The Passenger Power Seat Does Not Move Horizontally/Vertically - Vehicles Without Sir

Pinpoint Test E: The Passenger Power Seat Does Not Move Horizontally/Vertically - Vehicles Without Sir

WARNING: This page is about a different car, the 2005 Ford Pickup, 2005 Ford F550 Super Duty, 2005 Ford F450 Super Duty, and 2005 Ford Cab & Chassis. However, it is still accessible from the selected car via links, so may be relevant.

Test Step 

  1. E1 DETERMINE WHICH DIRECTION HAS FAILED 
    • Key in OFF position.
    • Operate the power seat forward and rearward.
    • Will the track move horizontally? 

    Result / Action to Take 

    • Yes  : GO to  E5.
    • No  : GO to  E6.
  2. E2 CHECK THE VOLTAGE TO FORWARD REVERSE SEAT MOTOR 
    • Disconnect: Power Seat Motor Assembly C3015.
    • Measure the voltage between power seat motor assembly C3015, circuit 986 (YE/WH), harness side and C3015, circuit 987 (RD/WH), harness side while pushing the forward/reverse switch forward and backward.
      Fig 1: Checking Voltage Between Connector Terminals
      G03890780Courtesy of FORD MOTOR CO.
    • Is the voltage greater than -10 volts when the forward/reverse switch is pressed forward, greater than +10 volts when the forward/reverse switch is pressed backward and 0 volts when the switch is in the rest position? 
  3. E3 CHECK CIRCUIT 986 (YE/WH) FOR AN OPEN AND SHORT TO GROUND 
    • Disconnect: Seat Control Switch C330.
    • Measure the resistance between seat control switch C330, circuit 986 (YE/WH), harness side and power seat motor assembly C3015, circuit 986 (YE/WH), harness side and between seat control switch C330, circuit 986 (YE/WH), harness side and ground.
      Fig 2: Checking Circuit 986 (YE/WH) For Open And Short To Ground
      G03911344Courtesy of FORD MOTOR CO.
    • Is the resistance less than 5 ohms between the power seat motor assembly and the seat control switch, and greater than 10,000 ohms between the seat control switch and ground? 
    • Yes  : GO to E4.
    • No  : REPAIR circuit 986 (YE/WH). TEST the system for normal operation.
  4. E4 CHECK CIRCUIT 987 (RD/WH) FOR AN OPEN AND SHORT TO GROUND 
    • Measure the resistance between seat control switch C330, circuit 987 (RD/WH), harness side and power seat motor assembly C3015, circuit 987 (RD/WH), harness side and between seat control switch C330, circuit 987 (RD/WH), harness side and ground.
      Fig 3: Checking Circuit 987 (RD/WH) For Open And Short To Ground
      G03925378Courtesy of FORD MOTOR CO.
    • Is the resistance less than 5 ohms between the power seat motor assembly and the seat control switch, and greater than 10,000 ohms between the seat control switch and ground? 
    • Yes  : INSTALL a new seat control switch. REFER to SEAT CONTROL SWITCH  in this article. TEST the system for normal operation.
    • No  : REPAIR circuit 987 (RD/WH). TEST the system for normal operation.
  5. E5 DETERMINE SEAT TILTING FAILURE 
    • Determine seat tilting failure.
    • Can the seat be tilted forward or backward? 
    • Yes  : If only the forward tilting operates, GO to E6.

      If only the rear tilting operates, GO to  E9.

    • No  : INSTALL a new seat control switch. REFER to SEAT CONTROL SWITCH  in this article. TEST the system for normal operation.
  6. E6 CHECK THE VOLTAGE TO THE REAR HEIGHT MOTOR 
    • Disconnect: Power Seat Motor Assembly C3015.
    • Measure the voltage between power seat motor assembly C3015, circuit 989 (RD/LG), harness side and C3015, circuit 988 (YE/LG), harness side while depressing the rear tilt switch up and down.
      Fig 4: Checking Voltage To Rear Height Motor
      G03890786Courtesy of FORD MOTOR CO.
    • Is the voltage greater than +10 volts when the rear tilt switch is pressed up, greater than -10 volts when the rear tilt switch is pressed down and 0 volts when the switch is in the rest position? 
  7. E7 CHECK CIRCUIT 989 (RD/LG) FOR OPEN AND SHORT TO GROUND 
    • Disconnect: Seat Control Switch C330.
    • Measure the resistance between seat control switch C330, circuit 989 (RD/LG), harness side and power seat motor assembly C3015, circuit 989 (RD/LG), harness side and between seat control switch C330, circuit 989 (RD/LG), harness side and ground.
      Fig 5: Checking Circuit 989 (RD/LG) For Open And Short To Ground
      G03911347Courtesy of FORD MOTOR CO.
    • Is the resistance less than 5 ohms between the power seat motor assembly and the seat control switch, and greater than 10,000 ohms between the seat control switch and ground? 
    • Yes  : GO to E8.
    • No  : REPAIR circuit 989 (RD/LG). TEST the system for normal operation.
  8. E8 CHECK CIRCUIT 988 (YE/LG) FOR OPEN AND SHORT TO GROUND 
    • Measure the resistance between seat control switch C330, circuit 988 (YE/LG), harness side and power seat motor assembly C3015, circuit 988 (YE/LG), harness side and between seat control switch C330, circuit 988 (YE/LG), harness side and ground.
      Fig 6: Checking Circuit 988 (YE/LG) For Open And Short To Ground
      G03911348Courtesy of FORD MOTOR CO.
    • Is the resistance less than 5 ohms between the power seat motor assembly and the seat control switch, and greater than 10,000 ohms between the seat control switch and ground? 
    • Yes  : INSTALL a new seat control switch. REFER to SEAT CONTROL SWITCH  in this article. TEST the system for normal operation.
    • No  : REPAIR circuit 988 (YE/LG). TEST the system for normal operation.
  9. E9 CHECK THE VOLTAGE TO FRONT HEIGHT MOTOR 
    • Disconnect: Power Seat Motor Assembly C3015.
    • Measure the voltage between power seat motor assembly C3015, circuit 985 (RD/LB), harness side and C3015, circuit 984 (YE/LB), harness side while pushing the rear tilting switch up and down.
      Fig 7: Checking Voltage To Front Height Motor
      G03890783Courtesy of FORD MOTOR CO.
    • Is the voltage greater than +10 volts when the front tilt switch is pressed up, greater than -10 volts when the front tilt switch is pressed down and 0 volts when the switch is in the rest position? 
  10. E10 CHECK CIRCUIT 985 (RD/LB) FOR OPEN AND SHORT TO GROUND 
    • Disconnect: Seat Control Switch C330.
    • Measure the resistance between control switch C330, circuit 985 (RD/LB), harness side and power seat motor assembly C3015, circuit 985 (RD/LB), harness side and between seat control switch C330, circuit 985 (RD/LB), harness side and ground.
      Fig 8: Checking Circuit 985 (RD/LB) For Open And Short To Ground
      G03911350Courtesy of FORD MOTOR CO.
    • Is the resistance less than 5 ohms between the power seat motor assembly and the seat control switch, and greater than 10,000 ohms between the seat control switch and ground? 
    • Yes  : GO to E11.
    • No  : REPAIR circuit 985 (RD/LB). TEST the system for normal operation.
  11. E11 CHECK CIRCUIT 984 (YE/LB) FOR OPEN 
    • Measure the resistance between seat control switch C330, circuit 984 (YE/LB), harness side and power seat motor assembly C3015, circuit 984 (YE/LB), harness side and between seat control switch C330, circuit 984 (YE/LB), harness side and ground.
      Fig 9: Checking Circuit 984 (YE/LB) For Open
      G03911351Courtesy of FORD MOTOR CO.
    • Is the resistance less than 5 ohms between the power seat motor assembly and the seat control switch, and greater than 10,000 ohms between the seat control switch and ground? 
    • Yes  : INSTALL a new seat control switch. REFER to SEAT CONTROL SWITCH  in this article. TEST the system for normal operation.
    • No  : REPAIR circuit 984 (YE/LB). TEST the system for normal operation.
scientia non olet · About LEMON Manuals