Instrument Cluster Dealer Test Mode
WARNING: This page is about a different car, the 2005 Ford RV Cutaway, 2005 Ford Econoline, and 2005 Ford E450 Super Duty. However, it is still accessible from the selected car via links, so may be relevant.
To enter the Instrument Cluster Dealer Test Mode, press and hold the instrument cluster SELECT/RESET button, then turn the ignition switch to the RUN position. Continue pressing the SELECT/RESET button (5 seconds) until TEST is displayed in the odometer. The SELECT/RESET button must be released within 5 seconds of the odometer displaying TEST to begin the dealer test mode. Press the SELECT/RESET button to advance through the following steps until the DTC is displayed. Pressing the SELECT/RESET button repeatedly will display all continuous DTCs stored before proceeding to the next step.
ODOMETER DISPLAY & DESCRIPTION
| Odometer Display | Description |
|---|---|
| SWEEP GAUGE | Carries out the gauge sweep of all the gauges, then displays the present gauge values. Also carries out the checksum tests on ROM and EE. |
| TEST BULBS/LEDS | Illuminates all the following micro-controlled lamps and light emitting diodes (LEDs). ABS, Brake, Low Fuel, Check Gauge, Check Fuel Cap, Safety Belt, Check Engine, Wait to Start, Water in Fuel, Electronic Throttle Control (ETC). |
| All segments illuminated | Proves out all the trip/ODO segments. |
| 5C2T PREFIX | Displays the alpha numeric part number prefix (first 4 digits). |
| XXXX SUFFIX | Suffix (last 2 digits of the part number are displayed as a 2-byte hexadecimal number). |
| Cluster Type XX | Displays the end item configuration byte. |
| KEY IGN X | Displays the key-in-ignition status. |
| ROMXXXX FAIL | Return to normal operation of all micro-controlled lamps/LEDs and displays hexadecimal ROM level. |
| NR XXXX FAIL | Displays the hexadecimal ROM level and type as stored in NVM. |
| EE XXXX FAIL | Displays the hexadecimal EE level. |
| MN DATE XXXX | Displays the hexadecimal coding of final manufacturing test date. |
| CF1-CF-4 XX | Displays the hexadecimal coding of 1st through 4th byte on module configuration settings. |
| DTC XXXX | Displays a 16-bit DTC in hexadecimal format. DTCs displayed are those detected in continuous operation and not during self-test. |
| MPH XXX.X | Displays the English speed value being input. The speedometer indicates the present speed. |
| KPH XXX.X | Displays the metric speed value being input. The speedometer indicates the present speed. |
| TACH XXXX | Displays the tachometer value being input. The tachometer indicates the present RPM. |
| FUEL AD XXX | Displays the present fuel level A/D input ratio in decimal. The fuel gauge indicates the present level. |
| FUEL PR XXX | Displays the present fuel level percent status in decimal. |
| C TEMP XXX | Displays the last temperature gauge input value from the HS CAN in degrees C, temperature gauge indicates the present temperature. |
| FSCXX | Displays the last received FSC message input. |
| ODO CNT XXX | Displays the odometer input received via the HS CAN, in decimal. |
| OIL PR XXX | Displays the last A/D reading of the oil pressure switch contact resistance. |
| BRKE FL XXX | Displays the brake fluid level received from the switch. |
| PR BRKE X | Displays the parking brake input. |
| PRNDL XX | Displays the PRNDL position. |
| BATTERY XX.X | Displays the present SBATT reading in volts. |
| RXX LXX VF XXXX | R- RHEO (RAD counts) L-LED output VF- VF display output. |
| DOOR 1-D X | Displays the input status of driver door ajar input. |
| DOOR2-P X | Displays the input status of passenger door ajar input. |
| DOOR3-S X | Displays the input status of sliding door ajar input. |
| SEATBLT X | Displays the input status of safety belt switch. |
| CHECK ENG XX | Displays the 8-bit hexadecimal value of the HS CAN service engine soon (MIL) telltale command. |
| PA, PB, PE, PH, PJ, PK, PL, PM, PP, PS, PY, PU, PV, PW XX | Displays the 8-bit hexadecimal value of the port readings. |
| PAD00, PAD01, AD00, AD01, AD02, AD03, AD04, AD05, AD06, AD07, AD10, AD11, AD12, AD13, AD14, AD15, AD16, AD17 XX | Displays the 8 bit hexadecimal value of the port A/D read. |
| SWEEP GAUGE | Repeats the test cycle. |
Turn the ignition switch to the OFF position to exit Instrument Cluster Dealer Test Mode. If no DTCs related to the concern are retrieved, GO to SYMPTOM CHART .