LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2000 >> Contour SE, 2.5 L, Standard >> Repair and Diagnosis >> External Pages >> Different car >> Section 633 (Safety Belt System) >> Removal And Installation >> Safety Belt Buckle and Pretensioner >> Removal and Installation

Removal and Installation

WARNING: This page is about a different car, the 2004 Ford RV Cutaway, 2004 Ford Econoline, 2004 Ford E450 Super Duty, and 2004 Ford Cutaway. However, it is still accessible from the selected car via links, so may be relevant.
WARNING: The safety belt pretensioner is a pyrotechnic device. Always wear safety glasses when repairing an air bag equipped vehicle and when handling a safety belt buckle pretensioner or safety belt retractor pretensioner. Never probe a pretensioner electrical connector. Doing so could result in pretensioner or air bag deployment and could result in personal injury.
WARNING: To reduce the risk of personal injury, do not use memory saver devices.
NOTE: If a seat equipped with a supplemental restraint system (SRS) component is being serviced, THE (SRS) MUST BE DEPOWERED. 
NOTE: The air bag warning lamp illuminates when the RCM fuse is removed and the ignition switch is ON. This is normal operation and does not indicate a supplemental restraint system (SRS) fault.
NOTE: The SRS must be fully operational and free of faults before releasing the vehicle to the customer.
NOTE: The driver seat is shown unless otherwise noted.

    ALL SEATS 

  1. Depower the SRS. Refer to DISABLING & ACTIVATING AIR BAG SYSTEM .
  2. Remove the seat with the affected safety belt buckle and pretensioner. For additional information, refer to SEATING .

    3. SEATS WITH POWER SEAT TRACK AND MANUAL LUMBAR 

  3. Pull and remove the lumbar adjustment knob.
    Fig 1: Removing Lumbar Adjustment Knob
    G02767541Courtesy of FORD MOTOR CO.
  4. Remove the screw.
    Fig 2: Removing Screw
    G02767542Courtesy of FORD MOTOR CO.

    5. SEATS WITH POWER SEAT TRACK AND INBOARD SIDE SHIELDS 

  5. Remove the screw from the underside of the inboard seat side shield.
    Fig 3: Removing Screw From The Underside Of The Inboard Seat Side Shield
    G02767543Courtesy of FORD MOTOR CO.
  6. Remove the screw from the front of the inboard side shield.
    Fig 4: Removing Screw From The Front Of The Inboard Side Shield
    G02767544Courtesy of FORD MOTOR CO.
  7. Remove the inboard side shield.
    1. Pull the inboard side shield away to clear the safety belt buckle and pretensioner.
    2. Rotate the inboard side shield upward to release the rear pin-type retainer.
      • Install a new pin-type retainer if damaged during removal.
    3. Hold the inboard side shield in one hand and release the retaining clips holding the safety belt buckle and pretensioner boot to the inboard side shield.
    4. Remove the inboard side shield.
      Fig 5: Removing Inboard Side Shield
      G02767545Courtesy of FORD MOTOR CO.

    8. SEATS WITH MANUAL SEAT TRACK AND INBOARD SIDE SHIELD 

    NOTE: Passenger seat shown.
    Fig 6: Removing Inboard Side Shield Screws From Underneath The Seat
    G02767546Courtesy of FORD MOTOR CO.
  8. Remove the inboard side shield screws from underneath the seat.
    9. NOTE: Passenger seat shown.
    Fig 7: Pulling The Inboard Side Shield Away To Clear The Safety Belt Buckle Pretensioner
    G02767547Courtesy of FORD MOTOR CO.
  9. Rotate the inboard side shield upward to disengage the front and center upper hooks.
    • Pull the inboard side shield away to clear the safety belt buckle pretensioner.
    10. NOTE: Passenger seat shown.
    Fig 8: Removing Inboard Side Shield
    G02767548Courtesy of FORD MOTOR CO.
  10. Remove the inboard side shield.
    1. Rotate the inboard side shield upward to release the rear pin-type retainer.
      • Install a new pin-type retainer if damaged during removal.
    2. Hold the inboard side shield in one hand and release the retaining clips holding the safety belt buckle pretensioner boot to the inboard side shield.
    3. Remove the inboard side shield.

    11. SEATS WITHOUT INBOARD SIDE SHIELD 

  11. Release the hook-and -loop strip on the inboard cushion flap.
    Fig 9: Releasing The Hook-And -Loop Strip On The Inboard Cushion Flap
    G02767549Courtesy of FORD MOTOR CO.
  12. Release the J-clip.
    Fig 10: Releasing The J-Clip
    G02767550Courtesy of FORD MOTOR CO.
  13. Release the push pin and position aside the inboard seat cushion flap.
    Fig 11: Releasing The Push Pin And Position Aside The Inboard Seat Cushion Flap
    G02767551Courtesy of FORD MOTOR CO.

    14. ALL SEATS 

    NOTE: The power seat track is shown, the manual track is similar.
    Fig 12: Removing Safety Belt Buckle Electrical Connector
    G02767552Courtesy of FORD MOTOR CO.
  14. Loosen the four bolts and separate the seat track and pedestal from the seat cushion to allow removal of the safety belt buckle electrical connector.
  15. Separate the electrical connector and wire harness pin-type retainers from the seat.
    Fig 13: Separating The Electrical Connector And Wire Harness Pin-Type Retainers From The Seat
    G02767553Courtesy of FORD MOTOR CO.
  16. Separate the wire harness pin-type retainer from the seat.
    Fig 14: Separating The Wire Harness Pin-Type Retainer From The Seat
    G02767554Courtesy of FORD MOTOR CO.
    17. NOTE: Seat with inboard side shield shown, seat without inboard side shield similar.
    Fig 15: Removing Safety Belt Buckle Pretensioner
    G02767555Courtesy of FORD MOTOR CO.
  17. Remove the safety belt buckle and pretensioner.
    1. Remove the bolt.
      • To install, tighten to 40 Nm (30 lb-ft).
    2. Separate the safety belt buckle and pretensioner.
    3. Route out the wire harness and remove the safety belt buckle pretensioner.
  18. To install, reverse the removal procedure.
  19. Install the seat with the affected safety belt buckle pretensioner. For additional information, refer to SEATING .
  20. Repower the SRS. Refer to DISABLING & ACTIVATING AIR BAG SYSTEM .
  21. Check the active restraint system for correct operation.
scientia non olet · About LEMON Manuals