Evaporative Emissions

The Evaporative Emission (EVAP) system consists of the:

• EVAP canister purge valve.
• EVAP canister (includes the dust separator and the vent solenoid).
• fuel vapor tube assembly (includes the Fuel Tank Pressure (FTP) sensor and the vapor blocking valve).
• Easy Fuel™ (capless) fuel tank filler pipe.

The EVAP system:

• prevents hydrocarbon emissions from reaching the atmosphere.
• stores fuel vapors in the EVAP canister, that are generated during vehicle operation or hot soak, until they can be consumed by the engine during normal engine operation.
• routes the stored fuel vapors to the engine during engine operation.
• is controlled by the PCM which, using various sensor inputs, calculates the desired amount of purge flow. The PCM regulates the purge flow, induced by the application of intake manifold vacuum, by varying the duty cycle applied to the EVAP canister purge valve.

The fuel vapors are routed:

• from the fuel tank through the fuel vapor vent valve.
• to the EVAP canisters through a vapor tube.
• from the EVAP canister to the engine when the EVAP canister purge valve is opened by the PCM.

The FTP sensor (part of fuel vapor tube assembly):

• monitors the pressure levels in the fuel tank.
• communicates the pressure reading to the PCM during the OBD II leak test.

The fuel vapor tube assembly:

• is located under the rear of the vehicle.
• is used to monitor fuel pressure and relay information to the PCM.
• includes the FTP sensor and the vapor blocking valve.

The EVAP canister:

• is located under the rear of the vehicle.
• includes the dust separator and vent solenoid.
• contains activated carbon.
• stores fuel vapors.

The Easy Fuel™ (capless) fuel tank filler pipe:

• relieves system vacuum below -3.5 kPa (-16.00 in H₂ O).

The EVAP canister vent solenoid:

• is normally open.
• seals the EVAP system for the inspection and maintenance (I/M 240) test and OBD II leak and pressure tests.
• is serviced as part of the EVAP canister.

The EVAP canister purge valve:

• is normally closed.
• regulates the purging of the EVAP canisters.
• is controlled by the PCM.
• is repaired as a separate item.
• is mounted to the intake manifold.

The dust separator:

• is attached to the EVAP canister vent solenoid.
• prevents suspended dust and dirt particles from entering the EVAP system.
• is serviced as part of the EVAP canister.

The EVAP system monitor:

• is a self-test strategy within the PCM which tests the integrity of the EVAP system.
• monitors the EVAP system for leaks.
• monitors electronic EVAP components for irrationally high or low voltages.
• monitors for correct EVAP system operation.
• uses negative and positive leak test methods to test and activate the EVAP system.

The engine ON EVAP leak-check monitor:

• is executed by the individual components of the enhanced EVAP system. Intake manifold vacuum is utilized to reach a target vacuum on the EVAP system. The FTP sensor is used by the engine ON EVAP leak-check monitor to determine if the target vacuum necessary to carry out the leak-check on the EVAP system has been reached. Once target vacuum on the EVAP system is achieved, the change in EVAP system vacuum over a calibrated period of time determines if a leak exists.

The Engine Off Natural Vacuum (EONV) EVAP leak-check monitor is executed:

• once the engine ON EVAP leak-check monitor is completed and the key is turned OFF. The EONV EVAP leak-check monitor determines if a leak is present when the naturally occurring change in the fuel tank pressure or vacuum does not exceed a calibrated limit during a calibrated amount of time. A separate, low-power consuming microprocessor in the PCM manages the EONV leak-check. The engine OFF EVAP leak-check monitor is executed by the individual components of the enhanced EVAP system.