LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2000 >> Contour SE, 2.5 L, Standard >> Repair and Diagnosis >> External Pages >> Different car >> Section 2614 (Engine Mechanical - 2.5L (Except Hybrid)) >> In-Vehicle Repair >> Cylinder Head >> Removal

Cylinder Head: Removal

WARNING: This page is about a different car, the 2011 Mercury Milan and 2011 Ford Fusion. However, it is still accessible from the selected car via links, so may be relevant.
NOTE: Do not loosen or remove the crankshaft pulley bolt without first installing the special tools as instructed in this procedure. The crankshaft pulley and the crankshaft timing sprocket are not keyed to the crankshaft. The crankshaft, the crankshaft sprocket and the pulley are fitted together by friction, using diamond washers between the flange faces on each part. For that reason, the crankshaft sprocket is also unfastened if the pulley bolt is loosened. Before any repair requiring loosening or removal of the crankshaft pulley bolt, the crankshaft and camshafts must be locked in place by the special service tools, otherwise severe engine damage can occur.
NOTE: During engine repair procedures, cleanliness is extremely important. Any foreign material, including any material created while cleaning gasket surfaces, that enters the oil passages, coolant passages or the oil pan can cause engine failure.
  1. With the vehicle in NEUTRAL, position it on a hoist. For additional information, refer to JACKING & LIFTING article.
  2. Release the fuel system pressure. For additional information, refer to FUEL SYSTEM - GENERAL INFORMATION - FUSION, MILAN & MKZ article.
  3. Check the valve clearance. For additional information, refer to VALVE CLEARANCE CHECK  in this service information.
  4. Drain the engine cooling system. For additional information, refer to ENGINE COOLING SYSTEM (EXCEPT HYBRID) article.
  5. Disconnect the degas bottle-to-radiator hose from the degas bottle.
  6. Remove the nut and bolt and position the degas bottle to access the lower degas bottle hose.
  7. Disconnect the lower degas bottle hose and remove the degas bottle.
  8. Remove the generator. For additional information, refer to CHARGING SYSTEM -- FUSION, MILAN & MKZ article.
  9. Remove the fuel supply rail. For additional information, refer to FUEL CHARGING & CONTROLS - 2.5L -- FUSION & MILAN (EXCEPT HYBRID) article.
  10. Remove the intake manifold. For additional information, refer to INTAKE MANIFOLD  in this service information.
  11. Remove the exhaust manifold. For additional information, refer to EXHAUST MANIFOLD  in this service information.
  12. Remove the bolt and the engine mount damper from the engine mount bracket.
  13. Remove the bolt and the ground wire from the engine mount bracket.
  14. Remove the engine mount bracket bolt.
  15. Install the Engine Lifting Brackets and a suitable length of chain to the threaded hole in the LH side of the engine block.
    Fig 1: Identifying Engine Lifting Bracket And Chain On LH Side Of Engine Block
    G07780697Courtesy of FORD MOTOR CO.
  16. Using the Engine Support Bar and Engine Lifting Brackets, lift the engine 25 mm (0.98 in).
    Fig 2: Lifting Engine Using Engine Support Bar And Engine Lifting Brackets
    G07780698Courtesy of FORD MOTOR CO.
  17. Remove the nut, 2 bolts and the engine mount.
  18. Lower the engine 25 mm (0.98 in).
  19. Remove the 2 nuts and the engine mount bracket.
  20. Remove the timing drive components. For additional information, refer to TIMING DRIVE COMPONENTS  in this service information.
  21. Remove the Camshaft Alignment Plate.
    Fig 3: Identifying Camshaft Alignment Plate
    G07780699Courtesy of FORD MOTOR CO.
  22. Mark the position of the camshaft lobes on the No. 1 cylinder for installation reference.
    Fig 4: Locating Camshaft Lobe Position On The No. 1 Cylinder
    G07780700Courtesy of FORD MOTOR CO.
  23. Remove the bolt and the Variable Camshaft Timing (VCT) solenoid.
    24. NOTE: Failure to follow the camshaft loosening procedure can result in damage to the camshafts.
    NOTE: Mark the location and orientation of each camshaft bearing cap.
    Fig 5: Identifying Camshaft Bearing Cap Bolts Loosening Sequence
    G07780701Courtesy of FORD MOTOR CO.
  24. Remove the camshafts from the engine.
    • Loosen the camshaft bearing cap bolts, in the sequence shown in the illustration, one turn at a time until all tension is released from the camshaft bearing caps.
    • Remove the bolts and the camshaft bearing caps.
    • Remove the camshafts.
    25. NOTE: If the camshafts and valve tappets are to be reused, mark the location of the valve tappets to make sure they are assembled in their original positions.
    NOTE: The number on the valve tappets only reflects the digits that follow the decimal. For example, a tappet with the number 0.650 has the thickness of 3.650 mm.
  25. Remove and inspect the valve tappets. For additional information, refer to ENGINE SYSTEM - GENERAL INFORMATION article.
  26. Disconnect the upper radiator hose, coolant bypass hose and heater hose from the engine coolant outlet.
  27. Disconnect the EGR valve electrical connector.
  28. Disconnect the coolant hose from the EGR valve.
  29. Remove the 10 bolts and the cylinder head.
scientia non olet · About LEMON Manuals