LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2000 >> Contour SE, 2.5 L, Standard >> Repair and Diagnosis >> External Pages >> Different car >> Section 2454 (Supplemental Restraint System) >> Diagnosis And Testing >> Air Bag and Safety Belt Pretensioner Supplemental Restraint System (SRS) >> Pinpoint Test - Restraints Control Module (RCM) >> Pinpoint Test D: DTCs B0010:11, B0010:12, B0010:13 and B0010:1A >> PINPOINT TEST D: DTCs B0010:11, B0010:12, B0010:13 AND B0010:1A

PINPOINT TEST D: DTCs B0010:11, B0010:12, B0010:13 AND B0010:1A

WARNING: This page is about a different car, the 2010 Mercury Mariner and 2010 Ford Escape. However, it is still accessible from the selected car via links, so may be relevant.
WARNING: Do not handle, move or change the original horizontal mounting position of the restraints control module (RCM) while the RCM  is connected and the ignition switch is ON. Failure to follow this instruction may result in the accidental deployment of the Safety Canopy® and cause serious personal injury or death.
WARNING: Never probe the electrical connectors on air bag, Safety Canopy® or side air curtain modules. Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.
NOTE: Use the correct probe adapter(s) from the Flex Probe Kit when taking measurements. Failure to use the correct probe adapter(s) may damage the connector.
Most faults are due to connector and/or wiring concerns. Carry out a thorough inspection and verification before proceeding with the pinpoint test.
NOTE: Supplemental Restraint System (SRS) components should only be disconnected or reconnected when instructed to do so within a pinpoint test step. Failure to follow this instruction may result in incorrect diagnosis of the SRS  .
NOTE: Always make sure the correct SRS  component is being installed. Parts released for other vehicles may not be compatible even if they appear physically similar. Check the part number listed in the Ford Catalog Advantage™ or equivalent to make sure the correct component is being installed. If an incorrect SRS  component is installed, DTCs may set.
NOTE: The SRS  must be fully operational and free of faults before releasing the vehicle to the customer.
  1. D1 RETRIEVE RCM DTCs 
    • Ignition ON.
    • Enter the following diagnostic mode on the scan tool: Self Test - RCM  .
    • Was DTC B0010:11, B0010:12, B0010:13 or B0010:1A retrieved on-demand during self-test? 
    • Yes:  This fault cannot be cleared until it is corrected and the DTC is no longer retrieved on-demand during self-test.

      For DTC B0010:13 or B0010:1A, GO to D2  .

      For DTC B0010:11, GO to  D9.

      For DTC B0010:12, GO to  D11.

    • No:  This is an intermittent fault when present as a CMDTC only.

      For DTC B0010:13 or B0010:1A, GO to  D14.

      For DTC B0010:11, GO to  D15.

      For DTC B0010:12, GO to  D16.

  2. D2 CHECK THE PASSENGER FRONTAL STAGE 1 DEPLOYMENT CONTROL RESISTANCE (DEPLOY_05_R) PID 
    • Enter the following diagnostic mode on the scan tool: DataLogger - RCM  .
      • DEPLOY_05_R PID
    • Does the PID value read between 1.7 and 2.78 ohms? 
    • Yes:  GO to  D13.
    • No:  GO to D3  .
  3. D3 CHECK THE PASSENGER FRONTAL STAGE 1 DEPLOYMENT CONTROL RESISTANCE (DEPLOY_05_R) PID WHILE CARRYING OUT THE HARNESS TEST 
    • While monitoring the DEPLOY_05_R PID, carry out the harness test of the passenger air bag module circuits and accessible connectors (including any in-line connectors) by wiggling connectors and flexing the wire harness.
    • Does the PID value read between 1.7 and 2.78 ohms while carrying out the harness test? 
    • Yes:  DEPOWER the SRS  and REPAIR the connector, terminals or wire harness as needed.

      Refer to appropriate SYSTEM WIRING DIAGRAMS article, Connector Repair Procedures for schematic and connector information.

      GO to  D18.

    • No:  For PID value less than 1.7 ohms, GO to D4  .

      For PID value greater than 2.78 ohms, GO to  D7.

  4. D4 CHECK THE PASSENGER FRONTAL STAGE 1 DEPLOYMENT CONTROL DTC FOR A FAULT STATUS CHANGE (LOW RESISTANCE INDICATED) 
    NOTE: This pinpoint test step will attempt to change the fault reported by the RCM  by inducing a different fault condition. If the fault reported changes, this indicates the RCM  is functioning correctly and is not the source of the fault.
    • Yes:  GO to  D12.
    • No:  GO to D5  .
  5. D5 CHECK FOR A SHORT BETWEEN PASSENGER AIR BAG STAGE 1 CIRCUITS 
    • Ignition OFF.
    • Depower the SRS  . Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Measure the resistance between passenger air bag C256A-2, circuit CR103 (GY/BU), harness side and C256A-1, circuit RR103 (VT/GN), harness side.
      Fig 1: Measuring Resistance Between Passenger Air Bag C256A-2, Circuit CR103 (GY/BU) And C256A-1, Circuit RR103 (VT/GN)
      G06063642Courtesy of FORD MOTOR CO.
    • Is the resistance greater than 10,000 ohms? 
    • Yes:  GO to  D13.
    • No:  GO to D6  .
  6. D6 CHECK RCM FOR LOW RESISTANCE 
    • Disconnect: RCM  C2041A and C2041B.
    • Measure the resistance between RCM  C2041A pins 1 and 2, component side.
      Fig 2: Measuring Resistance Between RCM C2041A Pins 1 And 2
      G06100017Courtesy of FORD MOTOR CO.
    • Is the resistance greater than 10,000 ohms? 
    • Yes:  REPAIR circuits CR103 (GY/BU) and RR103 (VT/GN). GO to  D18.
    • No:  GO to  D13.
  7. D7 CHECK THE PASSENGER AIR BAG STAGE 1 CIRCUITS FOR AN OPEN 
    • Ignition OFF.
    • Depower the SRS  . Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Remove and disconnect the passenger air bag module. Refer to PASSENGER AIR BAG MODULE .
    • Disconnect: RCM  C2041A and C2041B.
    • Measure the resistance between RCM  C2041A, harness side and passenger air bag module C256A, harness side using the following chart.
      RCM SPECIFICATION

      RCM  Circuit Passenger Air Bag Module
      C2041A-1 CR103 (GY/BU) C256A-2
      C2041A-2 RR103 (VT/GN) C256A-1
      Fig 3: Measuring Resistance Between RCM C2041A And Passenger Air Bag Module C256A
      G06063721Courtesy of FORD MOTOR CO.
    • Are the resistances less than 0.5 ohm? 
    • Yes:  GO to D8  .
    • No:  REPAIR circuit CR103 (GY/BU) or RR103 (VT/GN). GO to  D18.
  8. D8 CHECK THE PASSENGER FRONTAL STAGE 1 DEPLOYMENT CONTROL DTC FOR A FAULT STATUS CHANGE (OPEN INDICATED) 
    NOTE: This pinpoint test step will attempt to change the fault reported by the RCM  by inducing a different fault condition. If the fault reported changes, this indicates the RCM  is functioning correctly and is not the source of the fault.
    • Connect: RCM  C2041A and C2041B.
    • Connect a fused jumper wire between passenger air bag module C256A-2, circuit CR103 (GY/BU), harness side and C256A-1, circuit RR103 (VT/GN), harness side.
    • Repower the SRS  . Do not  prove out the SRS  at this time. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Ignition ON.
    • Enter the following diagnostic mode on the scan tool: Self Test - RCM  .
    • DIAGNOSTIC TIP:  When viewing DTCs with the passenger air bag module stage 1 circuits shorted together, a low resistance fault would normally be retrieved on stage 1. Stage 2 will show an open circuit fault due to the passenger air bag being removed.
    • Did the on-demand DTC change from B0010:13 to B0010:1A? 
    • Yes:  GO to  D12.
    • No:  GO to  D13.
  9. D9 CHECK THE PASSENGER FRONTAL STAGE 1 DEPLOYMENT CONTROL DTC FOR A FAULT STATUS CHANGE (SHORT TO GROUND INDICATED) 
    NOTE: This pinpoint test step will attempt to change the fault reported by the RCM  by inducing a different fault condition. If the fault reported changes, this indicates the RCM  is functioning correctly and is not the source of the fault.
    • Yes:  GO to  D12.
    • No:  GO to D10  .
  10. D10 CHECK THE PASSENGER AIR BAG STAGE 1 CIRCUITS FOR A SHORT TO GROUND 
    • Ignition OFF.
    • Depower the SRS  . Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Disconnect: RCM  C2041A and C2041B.
    • Measure the resistance between passenger air bag module:
      • C256A-2, circuit CR103 (GY/BU), harness side and ground.
      • C256A-1, circuit RR103 (VT/GN), harness side and ground.
        Fig 4: Measuring Resistance Between Passenger Air Bag Module And C256A-2, Circuit CR103 (GY/BU), Harness Side
        G06063644Courtesy of FORD MOTOR CO.
    • Are the resistances greater than 10,000 ohms? 
    • Yes:  GO to  D13.
    • No:  Due to the shorting bar feature in the RCM  electrical connector, the fault can exist in either circuit. Do not remove or defeat the shorting bar.

      REPAIR circuit CR103 (GY/BU) or RR103 (VT/GN). GO to  D18.

  11. D11 CHECK THE PASSENGER AIR BAG STAGE 1 CIRCUITS FOR A SHORT TO VOLTAGE 
    • Yes:  Due to the shorting bar feature in the RCM  electrical connector, the fault can exist in either circuit. Do not remove or defeat the shorting bar.

      REPAIR circuit CR103 (GY/BU) or RR103 (VT/GN). GO to  D18.

    • No:  GO to  D13.
  12. D12 CONFIRM THE PASSENGER AIR BAG MODULE FAULT 
    NOTE: Make sure all restraint system components and the RCM  electrical connectors are connected before carrying out the self-test. If not, DTCs will be recorded.
    • Ignition OFF.
    • Depower the SRS  . Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • If previously installed, remove the fused jumper wire from the air bag module electrical connector.
    • Prior to reconnecting any previously disconnected SRS  component:
      • inspect connector(s) (including any in-line connectors) for pushed-out, loose or spread terminals and loose or frayed wire connections at terminals.
      • inspect wire harness for any damage, pinched, cut or pierced wires.
      • inspect C2041A and C2041B CPA lever/lock for correct operation. Refer to RESTRAINTS CONTROL MODULE (RCM) .
      • repair any concerns found.

        Refer to appropriate SYSTEM WIRING DIAGRAMS article, Connector Repair Procedures for schematic and connector information.

    • Connect and install the passenger air bag module (if previously disconnected). Refer to PASSENGER AIR BAG MODULE .
    • Repower the SRS  . Do not  prove out the SRS  at this time. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Ignition ON.
    • Enter the following diagnostic mode on the scan tool: Self Test - RCM  .
    • Was the original DTC retrieved on-demand during self-test? 
    • Yes:  INSTALL a new passenger air bag module. REFER to PASSENGER AIR BAG MODULE . GO to  D18.
    • No:  In the process of diagnosing the fault, the fault condition has become intermittent. Do not install any new SRS components at this time. SRS components should only be installed when directed to do so in the pinpoint test. 

      For DTC B0010:13 or B0002:1A, GO to  D14.

      For DTC B0010:11, GO to  D15.

      For DTC B0010:12, GO to  D16.

  13. D13 CONFIRM THE RCM FAULT 
    NOTE: Make sure all restraint system components and the RCM  electrical connectors are connected before carrying out the self-test. If not, DTCs will be recorded.
    • Ignition OFF.
    • Depower the SRS  . Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • If previously installed, remove the fused jumper wire from the air bag module electrical connector.
    • Prior to reconnecting any previously disconnected SRS  component:
      • inspect connector(s) (including any in-line connectors) for pushed-out, loose or spread terminals and loose or frayed wire connections at terminals.
      • inspect wire harness for any damage, pinched, cut or pierced wires.
      • inspect C2041A and C2041B CPA lever/lock for correct operation. Refer to RESTRAINTS CONTROL MODULE (RCM) .
      • repair any concerns found.

        Refer to appropriate SYSTEM WIRING DIAGRAMS article, Connector Repair Procedures for schematic and connector information.

    • Connect and install the passenger air bag module (if previously disconnected). Refer to PASSENGER AIR BAG MODULE .
    • Connect: RCM  C2041A and C2041B.
    • Repower the SRS  . Do not  prove out the SRS  at this time. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Ignition ON.
    • Enter the following diagnostic mode on the scan tool: Self Test - RCM  .
    • Was the original DTC retrieved on-demand during self-test? 
    • Yes:  INSTALL a new RCM  . REFER to RESTRAINTS CONTROL MODULE (RCM) . GO to  D18.
    • No:  In the process of diagnosing the fault, the fault condition has become intermittent. Do not install any new SRS components at this time. SRS components should only be installed when directed to do so in the pinpoint test. 

      For DTC B0010:13 or B0010:1A, GO to D14  .

      For DTC B0010:11, GO to  D15.

      For DTC B0010:12, GO to  D16.

  14. D14 CHECK THE PASSENGER FRONTAL STAGE 1 DEPLOYMENT CONTROL RESISTANCE (DEPLOY_05_R) PID FOR AN INTERMITTENT LOW RESISTANCE OR OPEN CIRCUIT FAULT 
    • Enter the following diagnostic mode on the scan tool: DataLogger - RCM  .
      • DEPLOY_05_R PID
    • Attempt to recreate the fault by wiggling connectors (including any in-line connectors) and flexing the wire harness frequently.
    • Does the PID value read between 1.7 and 2.78 ohms? 
    • Yes:  DEPOWER the SRS  and REPAIR as necessary.

      Refer to appropriate SYSTEM WIRING DIAGRAMS article, Connector Repair Procedures for schematic and connector information.

      GO to  D17.

    • No:  The fault is not present and cannot be recreated at this time. Do not install any new SRS components at this time. SRS components should only be installed when directed to do so in the pinpoint test.  GO to  D18.
  15. D15 CHECK THE PASSENGER FRONTAL STAGE 1 DEPLOYMENT CONTROL FOR AN INTERMITTENT SHORT TO GROUND FAULT 
    • Attempt to recreate the fault by wiggling connectors (including any in-line connectors) and flexing the wire harness.
    • Was DTC B0010:11 retrieved on-demand during self-test? 
    • Yes:  DEPOWER the SRS  and REPAIR as necessary.

      Refer to appropriate SYSTEM WIRING DIAGRAMS article, Connector Repair Procedures for schematic and connector information.

      GO to  D18.

    • No:  The fault is not present and cannot be recreated at this time. Do not install any new SRS components at this time. SRS components should only be installed when directed to do so in the pinpoint test.  GO to  D17.
  16. D16 CHECK THE PASSENGER FRONTAL STAGE 1 DEPLOYMENT CONTROL FOR AN INTERMITTENT SHORT TO BATTERY FAULT 
    • Yes:  DEPOWER the SRS  and REPAIR as necessary.

      Refer to appropriate SYSTEM WIRING DIAGRAMS article, Connector Repair Procedures for schematic and connector information.

      GO to  D18.

    • No:  The fault is not present and cannot be recreated at this time. Do not install any new SRS components at this time. SRS components should only be installed when directed to do so in the pinpoint test.  GO to D17  .
  17. D17 CHECK THE HARNESS AND CONNECTORS 
    • Ignition OFF.
    • Depower the SRS  . Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Remove and disconnect the passenger air bag module. Refer to PASSENGER AIR BAG MODULE .
      • inspect connector(s) (including any in-line connectors) for corrosion, loose or spread terminals and loose or frayed wire connections at terminals.
      • inspect wire harness for any damage, pinched, cut or pierced wires.
      • inspect C2041A and C2041B Connector Position Assurance (CPA) lever/lock for correct operation. Refer to RESTRAINTS CONTROL MODULE (RCM) .
    • Were any concerns found? 
    • Yes:  REPAIR as necessary.

      Refer to appropriate SYSTEM WIRING DIAGRAMS article, Connector Repair Procedures for schematic and connector information.

      GO to D18  .

    • No:  The fault is not present and cannot be recreated at this time. Do not install any new SRS components at this time. SRS components should only be installed when directed to do so in the pinpoint test.  GO to D18  .
  18. D18 CHECK FOR ADDITIONAL SRS DTCs 
    • Ignition OFF.
      • WARNING: Turn the ignition OFF and wait one minute to deplete the backup power supply. Failure to follow this instruction may result in serious personal injury or death in the event of an accidental deployment.
    • Reconnect all SRS  components (if previously disconnected).
    • If previously directed to depower the SRS  , repower the SRS  . Do not  prove out the SRS  at this time. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Ignition ON.
    • Enter the following diagnostic mode on the scan tool: Self Test - Restraints.
      • NOTE: When selecting Restraints from the Self Test menu, DTCs will be retrieved from the RCM  and OCSM  .
    • Are any RCM and/or OCSM DTCs retrieved on-demand during self-test? 
    • Yes:  Do not clear any DTCs until all DTCs have been resolved. GO to the DTC CHARTS  for pinpoint test direction.
    • No:  CLEAR all RCM  and OCSM CMDTCs  . PROVE OUT the SRS  . Repair is complete. RETURN the vehicle to the customer.
scientia non olet · About LEMON Manuals