LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2000 >> Contour SE, 2.5 L, Standard >> Repair and Diagnosis >> External Pages >> Different car >> Section 2321 (Supplemental Restraint System) >> Diagnosis And Testing >> Air Bag and Safety Belt Pretensioner Supplemental Restraint System (SRS) >> Pinpoint Test - Supplemental Restraint System (SRS) >> Pinpoint Test P: DTCs B0095:11 and B0095:93 >> PINPOINT TEST P: DTCs B0095:11 AND B0095:93

PINPOINT TEST P: DTCs B0095:11 AND B0095:93

WARNING: This page is about a different car, the 2010 Mercury Milan, 2010 Lincoln MKZ, and 2010 Ford Fusion. However, it is still accessible from the selected car via links, so may be relevant.
NOTE: Use the correct probe adapter(s) from the Flex Probe Kit when taking measurements. Failure to use the correct probe adapter(s) may damage the connector.

Most faults are due to connector and/or wiring concerns. Carry out a thorough inspection and verification before proceeding with the pinpoint test.

NOTE: Supplemental Restraint System (SRS) components should only be disconnected or reconnected when instructed to do so within a pinpoint test step. Failure to follow this instruction may result in incorrect diagnosis of the SRS  .
NOTE: Always make sure the correct SRS  component is being installed. Parts released for other vehicles may not be compatible even if they appear physically similar. Check the part number listed in the Ford Catalog Advantage™ or equivalent to make sure the correct component is being installed. If an incorrect SRS  component is installed, DTCs may set.
NOTE: The SRS  must be fully operational and free of faults before releasing the vehicle to the customer.
NOTE: Do not probe any impact sensor. The impact sensor can not be tested using a multi-meter.
  1. P1 RETRIEVE RCM DTCs 
    • Ignition ON.
    • Enter the following diagnostic mode on the scan tool: Self Test - RCM. 
    • Was DTC B0095:11, B0095:81, B0095:93 or B0095:96 retrieved on-demand during self-test? 
    • Yes  : This fault cannot be cleared until it is corrected and the DTC is no longer retrieved on-demand during self-test.

      For DTC B0095:11, GO to P2  .

      For DTC B0095:93, GO to  P5.

    • No  : The fault is intermittent when present as a CMDTC only. GO to  P10.
  2. P2 CHECK THE RIGHT FRONT RESTRAINTS SENSOR DTC FOR A FAULT STATUS CHANGE (SHORT TO GROUND INDICATED) 
    NOTE: This pinpoint test step will attempt to change the fault reported by the RCM  by inducing a different fault condition. If the fault reported changes, this indicates the RCM  is functioning correctly and is not the source of the fault.
  3. P3 CHECK THE RH FRONT IMPACT SEVERITY SENSOR FEED CIRCUIT FOR A SHORT TO GROUND 
    • Ignition OFF.
    • Depower the SRS  . Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Disconnect: RCM  C310A and C310B.
    • Measure the resistance between RH front impact severity sensor C1465-1, circuit VR214 (WH/BU), harness side and ground.
      Fig 1: Measuring Resistance Between RH Front Impact Severity Sensor C1465-1, Circuit VR214 (WH/BU), Harness Side And Ground
      G06100054Courtesy of FORD MOTOR CO.
    • Is the resistance greater than 10,000 ohms? 
    • Yes  : GO to P4  .
    • No  : REPAIR circuit VR214 (WH/BU). GO to  P11.
  4. P4 CHECK FOR A SHORT BETWEEN RH FRONT IMPACT SEVERITY SENSOR CIRCUITS 
    • Measure the resistance between RH front impact severity sensor C1465-1, circuit VR214 (WH/BU), harness side and C1465-2, circuit RR130 (GN/BU), harness side.
      Fig 2: Checking Short Between RH Front Impact Severity Sensor Circuits
      G06063750Courtesy of FORD MOTOR CO.
    • Is the resistance greater than 10,000 ohms? 
    • Yes  : GO to  P9.
    • No  : REPAIR circuits VR214 (WH/BU) and RR130 (GN/BU). GO to  P11.
  5. P5 CHECK THE RH FRONT IMPACT SEVERITY SENSOR AND RCM CONNECTIONS (NO OPERATION INDICATED) 
    • Ignition OFF.
    • WARNING: Turn the ignition OFF and wait one minute to deplete the backup power supply. Failure to follow this instruction may result in serious personal injury or death in the event of an accidental deployment.
    • Inspect RH front impact severity sensor C1465 to be fully seated and locked.
    • Gain access to the RCM  and inspect C310A and C310B to be fully seated and locked. Refer to RESTRAINTS CONTROL MODULE (RCM) .
    • Ignition ON.
    • Enter the following diagnostic mode on the scan tool: Self Test - RCM. 
    • Was DTC B0095:93 retrieved on-demand during self-test? 
    • Yes  : GO to P6  .
    • No  : Fault corrected. GO to  P11.
  6. P6 CHECK THE RH FRONT IMPACT SEVERITY SENSOR FEED CIRCUIT FOR A SHORT TO VOLTAGE (NO OPERATION INDICATED) 
    • Ignition OFF.
    • Depower the SRS  . Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Disconnect: RH Front Impact Severity Sensor C1465.
    • Disconnect: RCM  C310A and C310B.
    • Repower the SRS  . Do not  prove out the SRS  at this time. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Ignition ON.
    • Measure the voltage between RH front impact severity sensor C1465-1, circuit VR214 (WH/BU), harness side and ground.
      Fig 3: Measuring Voltage Between RH Front Impact Severity Sensor C1465-1, Circuit VR214 (WH/BU), Harness Side And Ground
      G06255033Courtesy of FORD MOTOR CO.
    • Is any voltage present? 
    • Yes  : REPAIR circuit VR214 (WH/BU). GO to  P11.
    • No  : GO to P7  .
  7. P7 CHECK THE RH FRONT IMPACT SEVERITY SENSOR CIRCUITS FOR AN OPEN (NO OPERATION INDICATED) 
    • Ignition OFF.
    • Depower the SRS  . Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Measure the resistance between RCM  C310B, harness side and RH front impact severity sensor C1465, harness side using the following chart.
      RCM REFERENCE CHART

      RCM  Circuit RH Front Impact Severity Sensor 
      C310B-30 VR214 (WH/BU) C1465-1
      C310B-29 RR130 (GN/BU) C1465-2
      Fig 4: Measuring Resistance Between RCM C310B And RH Front Impact Severity Sensor C1465, Harness Side
      G06100069Courtesy of FORD MOTOR CO.
    • Are the resistances less than 0.5 ohm? 
    • Yes  : GO to P8  .
    • No  : REPAIR circuit VR214 (WH/BU) or RR130 (GN/BU). GO to  P11.
  8. P8 CHECK THE RIGHT FRONT RESTRAINTS SENSOR DTC FOR A FAULT STATUS CHANGE (NO OPERATION INDICATED) 
    NOTE: This pinpoint test step will attempt to change the fault reported by the RCM  by inducing a different fault condition. If the fault reported changes, this indicates the RCM  is functioning correctly and is not the source of the fault.
    • Connect: RCM  C310A and C310B.
    • Connect a fused jumper wire between RH front impact severity sensor C1465-1, circuit VR214 (WH/BU), harness side and C1465-2, circuit RR130 (GN/BU), harness side.
    • Repower the SRS  . Do not  prove out the SRS  at this time. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Ignition ON.
    • Enter the following diagnostic mode on the scan tool: Self Test - RCM. 
    • Did the DTC change from B0095:93 to B0095:11? 
  9. P9 CONFIRM THE RCM FAULT 
    NOTE: Make sure all restraint system components and the RCM  electrical connectors are connected before carrying out the self-test. If not, DTCs will be recorded.
    • Ignition OFF.
    • Depower the SRS  . Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • If previously installed, remove the fused jumper wire from the RH front impact severity sensor electrical connector.
    • Prior to reconnecting any previously disconnected SRS  component:
      • inspect connector(s) (including any in-line connectors) for pushed out, loose or spread terminals and loose or frayed wire connections at terminals.
      • inspect wire harness for any damage, pinched, cut or pierced wires.
      • inspect C310A and C310B Connector Position Assurance (CPA) lever/lock for correct operation. Refer to RESTRAINTS CONTROL MODULE (RCM) .
      • repair any concerns found.

        Refer to appropriate SYSTEM WIRING DIAGRAMS article for schematic and connector information.

    • Connect: RH Front Impact Severity Sensor C1465.
    • Connect: RCM  C310A and C310B (if previously disconnected).
    • Repower the SRS  . Do not  prove out the SRS  at this time. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Ignition ON.
    • Enter the following diagnostic mode on the scan tool: Self Test - RCM. 
    • Was the original DTC retrieved on-demand during self-test? 
    • Yes  : INSTALL a new RCM  . REFER to RESTRAINTS CONTROL MODULE (RCM) . GO to  P11.
    • No  : In the process of diagnosing the fault, the fault condition has become intermittent. Do not install any new SRS  components at this time. SRS components should only be installed when directed to do so in the pinpoint test.  GO to P10  .
  10. P10 CHECK FOR AN INTERMITTENT FAULT 
    • Ignition OFF.
    • Depower the SRS  . Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Disconnect: RH Front Impact Severity Sensor C1465.
    • Disconnect: RCM  C310A and C310B.
    • Inspect for the following:
      • inspect harness and component connectors for loose or spread terminals and loose or frayed wire connections at terminals.
      • inspect wire harness for any damage, pinched, cut or pierced wires.
      • inspect RCM  C310A and C310B CPA lever/lock for correct operation. Refer to RESTRAINTS CONTROL MODULE (RCM) .
      • repair any concerns found.

        Refer to appropriate SYSTEM WIRING DIAGRAMS article for schematic and connector information.

    • Connect: All Previously Disconnected Component(s)/Connector(s).
    • Repower the SRS  . Do not  prove out the SRS  at this time. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Ignition ON.
    • Enter the following diagnostic mode on the scan tool: Self Test - RCM. 
    • Was DTC B0095:11, B0095:81, B0095:93 or B0095:96 retrieved on-demand during self-test? 
    • Yes  : This fault cannot be cleared until it is corrected and the DTC is no longer retrieved on-demand during self-test.

      This fault cannot be cleared until it is corrected and the DTC is no longer retrieved on-demand during self-test.

      For DTC B0095:11, GO to  P2.

      For DTC B0095:93, GO to  P5.

    • No  : The fault is not present and cannot be recreated at this time. Do not install any new SRS  components at this time. SRS components should only be installed when directed to do so in the pinpoint test.  GO to P11  .
  11. P11 CHECK FOR ADDITIONAL SRS DTCs 
    • Ignition OFF.
    • WARNING: Turn the ignition OFF and wait one minute to deplete the backup power supply. Failure to follow this instruction may result in serious personal injury or death in the event of an accidental deployment.
    • Reconnect all SRS  components (if previously disconnected).
    • If previously directed to depower the SRS  , repower the SRS  . Do not  prove out the SRS  at this time. Refer to SUPPLEMENTAL RESTRAINT SYSTEM (SRS) DEPOWERING AND REPOWERING .
    • Ignition ON.
    • Enter the following diagnostic mode on the scan tool: Self Test - Restraints.
      NOTE: When selecting Restraints from the Self Test menu, DTCs will be retrieved from the RCM  and Occupant Classification System Module (OCSM).
    • Are any RCM  and/or OCSM retrieved on-demand during self-test? 
    • Yes  : Do not clear any DTCs until all DTCs have been resolved. GO to the DTC CHARTS  for pinpoint test direction.
    • No  : CLEAR all RCM  and OCSM CMDTCs  . PROVE OUT the SRS  . Repair is complete. RETURN the vehicle to the customer.
scientia non olet · About LEMON Manuals