Diagnostic Trouble Code (DTC) Charts

WARNING: This page is about a different car, the 2008 Ford RV Cutaway, 2008 Ford Econoline, 2008 Ford E450 Super Duty, and 2008 Ford Cutaway. However, it is still accessible from the selected car via links, so may be relevant.

NOTE: Some of the following DTC symptoms may experience multiple DTC symptoms. The loss of one or more gears could be experienced depending on transmission condition.

DTC CHART

Five Digit DTC	Component	Description	Condition	Symptom	Action
P0102, P0103, P1100, P1101	Mass Air Flow (MAF) Sensor	MAF concerns	MAF system inoperative may cause a transmission concern.	High/low line pressure, incorrect shift schedule, incorrect Torque Converter Clutch (TCC), engagement scheduling. Symptoms similar to Throttle Position (TP) failure.	REFER to the appropriate Engine Performance article^a .
P0112	Intake Air Temperature (IAT) Sensor	IAT indicates 125°C (254°F)	Voltage drops across IAT exceeds scale set for temperature 125°C (254°F).	High/low line pressure resulting in harsh or soft shifts.	REFER to the appropriate Engine Performance article^a .
P0113	IAT Sensor	IAT indicates -40°C (-40°F)	Voltage drop across IAT exceeds scale set for temperature -40°C (-40°F).	High/low line pressure, resulting in harsh or soft shifts.	REFER to the appropriate Engine Performance article^a .
P0114	IAT Sensor	IAT out of On-Board Diagnostic (OBD) range	IAT temperature higher or lower than expected during Key ON Engine OFF (KOEO) and Key ON Engine Running (KOER).	Rerun OBD test at normal operating temperature.	REFER to the appropriate Engine Performance article^a .
P0116	Engine Coolant Temperature (ECT) Sensor	ECT out of OBD range	ECT temperature higher of lower than expected during KOEO and KOER.	Rerun OBD test at normal operating temperature.	REFER to the appropriate Engine Performance article.
P0117	ECT Sensor	ECT indicates 125°C (254°F)	Voltage drop across ECT exceeds scale set for temperature 125°C (254°F).	TCC will always be off, resulting in reduced fuel economy.	REFER to the appropriate Engine Performance article.
P0118	ECT Sensor	ECT indicates -40°C (-40°F)	Voltage drop across ECT exceeds scale set for temperature -40°C (-40°F)	TCC will always be off, resulting in reduced fuel economy.	REFER to the appropriate Engine Performance article.
P0121, P0122, P0123, P1120, P1121, P1124, P1125	Throttle Position (TP) Sensor	TP concern	PCM has detected an error. This error may cause a transmission concern.	Harsh engagements, firm shift feel, abnormal shift schedule, TCC does not engage, TCC cycling.	REFER to the appropriate Engine Performance article^a .
P0300, P0308, P0320, P0340, P1351- 1364	Electronic Ignition (EI) System	EI concerns	EI system is inoperative, which may cause a transmission concern.	Harsh engagements, and shifts, late Wide Open Throttle (WOT) shifts, no TCC engagement.	REFER to the appropriate Engine Performance article^a .
P0500, P1502	ABS	Insufficient Vehicle Speed Sensor (VSS) input from ABS through Standard Corporate Protocol (SCP) link	PCM detected a loss of VSS signal through SCP link from ABS.	No transmission symptom, Instrument Cluster (IC), speedometer may be affected.	REFER to the appropriate Engine Performance article^a .
P0503	ABS	Intermittent VSS input from ABS through SCP link	PCM detected an intermittent loss of VSS signal through SCP link from ABS.	No transmission symptom, IC, speedometer may be affected.	REFER to the appropriate Engine Performance article^a .
P0700	PCM/Transmission Control Module (TCM)	Transmission control system DTC present	TCM has sent a DTC error code to PCM indicating that additional TCM DTCs may be present.	Malfunction Indicator Lamp (MIL) may be illuminated. Other transmission concerns present.	Code set in PCM to indicate that there is a transmission code(s) present and tech should check the TCM for codes. Rerun OBD test and retrieve transmission DTCs from TCM.
P0706	Transmission Range (TR) Sensor	TR sensor frequency fault detected	TR sensor signal frequency is out of normal range.	Only REVERSE, NEUTRAL and 5th gear detected. Engine may not crank.	For gasoline engines Go to Pinpoint Test C . For diesel engines Go to Pinpoint Test H .
P0707	TR Sensor	TR sensor circuit duty cycle low input	TR sensor signal duty cycle is below threshold, sensor/circuit electrical malfunction.	Only REVERSE, NEUTRAL and 5th gear detected. Engine may not crank.	For gasoline engines Go to Pinpoint Test C . For diesel engines Go to Pinpoint Test H .
P0708	TR Sensor	TR sensor circuit duty cycle high input	TR sensor signal duty cycle is above threshold, sensor/circuit electrical malfunction.	Only REVERSE, NEUTRAL and 5th gear detected. Engine may not crank.	For gasoline engines Go to Pinpoint Test C . For diesel engines Go to Pinpoint Test H .
P1702	TR Sensor	TR error	TR sensor error detected.	Only REVERSE, NEUTRAL and 5th gear detected. Engine may not crank.	For gasoline engines Go to Pinpoint Test C . For diesel engines Go to Pinpoint Test H .
P1705	TR Sensor	TR sensor not in P or N positions during KOEO or KOER	KOEO or KOER not run in P or N positions, or TR sensor circuit failure.	DTC is set.	RERUN KOEO and KOER in P or N position. For gasoline engines Go to Pinpoint Test C . For diesel engines Go to Pinpoint Test H .
P0711	Transmission Fluid Temperature (TFT) Sensor	No change if TFT during operation	PCM has detected no TFT voltage change during operation.	No 5th or 6th gears.	For gasoline engines Go to Pinpoint Test B . For diesel engines Go to Pinpoint Test G .
P0712, P0710	TFT Sensor	157°C (315°F) indicated, TFT sensor circuit grounded	Voltage drop across TFT sensor exceeds scale set for temperature of 157°C (315°F).	No 5th or 6th gears.	For gasoline engines Go to Pinpoint Test B . For diesel engines Go to Pinpoint Test G .
P0713, P0710	TFT Sensor	-40°C (-40°F) indicated, TFT sensor circuit open	Voltage drop across TFT sensor exceeds scale set for temperature of -40°C (-40°F).	No 5th or 6th gears.	For gasoline engines Go to Pinpoint Test B . For diesel engines Go to Pinpoint Test G .
P1711	TFT Sensor	TFT out of range during OBD test	Transmission not operating at temperature during OBD test.	DTC set: engine cold or overheated.	Warm or cool engine to normal operating temperature. For gasoline engines Go to Pinpoint Test B . For diesel engines Go to Pinpoint Test G .
P1783	TFT Sensor	Transmission over temp condition indicated	TFT exceeded 127°C (270°F).	Torque converter engages earlier than expected.	For gasoline engines Go to Pinpoint Test B . For diesel engines Go to Pinpoint Test G .
P0715	Turbine Shaft Speed (TSS) Sensor	Insufficient input from TSS	PCM detected a loss of TSS signal during operation.	Harsh shifts and engagements, engine RPM higher or lower than expected. No 1st, 3rd or 5th gear.	For gasoline engines Go to Pinpoint Test D . For diesel engines Go to Pinpoint Test I .
P0717	TSS Sensor	No TSS signal	PCM has not detected a TSS signal.	Harsh shifts and engagements, engine RPM higher or lower than expected. No 1st, 3rd or 5th gear.	For gasoline engines Go to Pinpoint Test D . For diesel engines Go to Pinpoint Test I .
P0718	TSS Sensor	TSS signal noisy	PCM has detected a noisy TSS signal.	-	For gasoline engines Go to Pinpoint Test D . For diesel engines Go to Pinpoint Test I .
P0720	Output Shaft Speed (OSS) Sensor	Insufficient input from OSS	PCM detected a loss of OSS signal during operation.	No 1st, 2nd, 3rd, 4th or 6th gear.	For gasoline engines Go to Pinpoint Test D . For diesel engines Go to Pinpoint Test I .
P0721	OSS Sensor	OSS signal noisy	PCM has detected a noisy OSS signal.	-	For gasoline engines Go to Pinpoint Test D . For diesel engines Go to Pinpoint Test I .
P0722	OSS Sensor	No OSS signal	PCM has detected no OSS signal.	No 1st, 2nd, 3rd, 4th or 6th gear.	For gasoline engines Go to Pinpoint Test D . For diesel engines Go to Pinpoint Test I .
P0730	Clutch Control Solenoid or Internal Parts	Gear ratio error	PCM has detected a gear ratio error. One-Way Clutch (OWC) or clutches may have failed.	Incorrect gear selection depending on failure or mode and manual control position. Shift errors may also be due to other internal transmission concerns (stuck valves, damaged friction material). Engine RPM could be higher or lower than expected. May flash Transmission Control Indicator Lamp (TCIL).	SEE PID P0730_Status Chart. REFER to Diagnostic Parameters Identification (PID) Chart , for a specific failure. For gasoline engines Go to Pinpoint Test A . For diesel engines Go to Pinpoint Test F . REFER to the Solenoid Application charts located at the beginning of Pinpoint Tests - OSC Equipped Vehicle . If other solenoid DTCs are present, for gasoline engines Go to Pinpoint Test A . For diesel engines Go to Pinpoint Test F . If only P0730 and/or 2700 series DTCs are present, INSTALL the appropriate clutch solenoid. CLEAR the DTCs, road test vehicle. If the concern is still present, REPAIR/INSTALL new internal transmission components.
P0740^a	TCC Solenoid	TCC solenoid open circuit failure	TCC solenoid circuit fails to provide voltage drop across solenoid. Circuit open.	Open circuit: TCC never engages.	For gasoline engines Go to Pinpoint Test A . For diesel engines Go to Pinpoint Test F .
P0741	TCC Solenoid	TCC solenoid circuit performance error	Torque converter slippage detected during engagement command indicating a concern with mechanical or hydraulic operation of the converter clutch.	TCC slippage when commanded on indicating a concern with the mechanical or hydraulic TCC operation. No TCC engagement.	REFER to Diagnosis By Symptom .
P0742	TCC Solenoid	TCC solenoid circuit shorted to ground	TCC solenoid circuit fails to provide voltage drop across solenoid. Shorted to ground.	Short circuit: Only 5th gear at low vehicle speeds.	For gasoline engines Go to Pinpoint Test A . For diesel engines Go to Pinpoint Test F .
P0743	TCC Solenoid	TCC solenoid circuit failure	TCC solenoid circuit fails to provide voltage drop across solenoid. Circuit open, shorted or PCM driver failure during OBD test.	Open circuit: TCC never engages. Maximum Pressure Control Solenoid A (PCA) pressure, harsh engagement and shifts. Short circuit: Only 5th gear.	For gasoline engines Go to Pinpoint Test A . For diesel engines Go to Pinpoint Test F .
P0744	TCC Solenoid	TCC solenoid circuit shorted to power	TCC solenoid circuit fails to provide voltage drop across solenoid. Circuit shorted to power.	No TCC engagement.	For gasoline engines Go to Pinpoint Test A . For diesel engines Go to Pinpoint Test F .
P1744	TCC Solenoid	TCC solenoid circuit performance error	Torque converter slippage detected during engagement command indicating a concern with mechanical or hydraulic operation of the TCC.	TCC slippage when commanded on indicating a concern with the mechanical or hydraulic TCC operation. No TCC engagement.	REFER to Diagnosis By Symptom .
P0748^b	Line PCA	PCA circuit failure	Voltage through PCA is checked. An error will be noted if tolerance is exceeded.	Open circuit: maximum PCA pressure, harsh engagements and shift. Engine RPM higher than expected. Only 5th gear present. Maximum PCA pressure, harsh engagements and shifts. Engine RPM higher than expected.	For gasoline engines Go to Pinpoint Test E . For diesel engines Go to Pinpoint Test J .
P0960^b	Line PCA	PCA circuit open failure	Voltage through PCA is checked. An error will be noted if calibration is exceeded.	Open circuit: maximum PCA pressure, harsh engagements and shifts. Engine RPM higher than expected.	For gasoline engines Go to Pinpoint Test E . For diesel engines Go to Pinpoint Test J .
P0962^b	Line PCA	PCA circuit open failure	Voltage through PCA is checked. An error will be noted if calibration is exceeded.	Short circuit: Only 5th gear present.	For gasoline engines Go to Pinpoint Test E . For diesel engines Go to Pinpoint Test J .
P0963	Line PCA	PCA short to power circuit failure	Voltage through PCA is checked. An error will be noted if calibration is exceeded.	Maximum PCA pressure, harsh engagements and shifts. Engine RPM higher than expected.	For gasoline engines Go to Pinpoint Test E . For diesel engines Go to Pinpoint Test J .
P0750^a	Shift Solenoid Pressure Control A (SSPCA) Coast Clutch	SSPCA solenoid circuit open	SSPCA circuit failed to provide voltage drop across solenoid. Circuit open or PCM driver failure during OBD test.	No 2nd, 4th or 6th gear.	For gasoline engines Go to Pinpoint Test A . For diesel engines Go to Pinpoint Test F .
P0751	SSPCA Coast Clutch	SSPCA clutch or solenoid failure - OFF	SSPCA clutch or solenoid failed in the OFF position during operation resulting in HIGH pressure in the hydraulic circuit.	Tow/Haul OFF: Normal driving mode. No 1st gear available. Tow/Haul ON: No 1st, 3rd or 5th gears available.	REFER to Diagnosis By Symptom .
P0752	SSPCA Coast Clutch	SSPCA clutch or solenoid failure - ON	SSPCA clutch or solenoid failed in the ON position during operation resulting in LOW pressure in the hydraulic circuit.	Tow/Haul OFF: Normal driving mode. Temperature below -15°C (4°F), only 4th gear is operative. Temperature above -15°C (4°F), only 6th gear is operative. Tow/Haul ON: No 2nd, 4th or 6th gears available.	REFER to Diagnosis By Symptom .
P0753^a	SSPCA Coast Clutch	SSPCA solenoid circuit failure	SSPCA circuit failed to provide voltage drop across solenoid. Circuit failure or PCM driver failure.	Tow/Haul OFF: No 2nd, 4th, 5th or 6th gears available. No gears available. Tow/Haul ON: No 1st, 2nd, 3rd, 4th or 6th gears available.	For gasoline engines Go to Pinpoint Test A . For diesel engines Go to Pinpoint Test F .
P0973	SSPCA Coast Circuit	SSPCA solenoid or circuit shorted to ground	Voltage through SSPCA solenoid circuit is checked. An error will be noted if calibration is exceeded. Short to ground failure detected.	Tow/Haul OFF: No 2nd, 4th, 5th or 6th gears available. Tow/Haul ON: No 1st, 2nd, 3rd, 4th or 6th gears available.	For gasoline engines Go to Pinpoint Test A . For diesel engines Go to Pinpoint Test F .
P0974	SSPCA Coast Clutch	SSPCA solenoid or circuit shorted to power	Voltage through SSPCA solenoid circuit is checked. An error will be noted if calibration is exceeded. Short to power failure detected.	Tow/Haul OFF: No gears available. Tow/Haul ON: No 2nd, 4th or 6th gears available.	For gasoline engines Go to Pinpoint Test A . For diesel engines Go to Pinpoint Test F .
P0755^a	Shift Solenoid Pressure Control B (SSPCB) O/D Clutch	SSPCB solenoid circuit open	SSPCB circuit, clutch or solenoid failed to provide voltage drop across solenoid. Circuit open or PCM driver failure during OBD test.	Tow/Haul OFF: Only 1st or 3rd gears available. Tow/Haul ON: Only 5th gear available.	For gasoline engines Go to Pinpoint Test A . For diesel engines Go to Pinpoint Test F .
P0756	SSPCB O/D Clutch	SSPCB clutch or solenoid - OFF	SSPCB clutch or solenoid failed in the OFF position during operation resulting in LOW pressure in the hydraulic circuit.	Tow/Haul OFF: No 2nd gear available. Tow/Haul ON: No 2nd, 4th or 6th gears available.	REFER to Diagnosis By Symptom .
P0757	SSPCB O/D Clutch	SSPCB clutch or solenoid failure - ON	SSPCB clutch or solenoid failed in the ON position during operation resulting in HIGH pressure in the hydraulic circuit.	No 1st, 3rd, or 5th gears available.	REFER to Diagnosis By Symptom .
P0758^a	SSPCB O/D Clutch	SSPCB circuit failure	SSPCB circuit failed to provide voltage drop across solenoid. Circuit failure or PCM driver failure.	Tow/Haul OFF: Only 1st or 3rd gears available. No second available. Tow/Haul ON: No 5th gear available. Only 4th, 5th and 6th gears available.	For gasoline engines Go to Pinpoint Test A . For diesel engines Go to Pinpoint Test F .
P0976	SSPCB O/D Clutch	SSPCB solenoid or circuit shorted to ground	Voltage through SSPCB solenoid circuit is checked. An error will be noted if calibration is exceeded. Short to ground failure detected.	Tow/Haul OFF: No 2nd available. Tow/Haul ON: Only 4th and 6th gears available.	For gasoline engines Go to Pinpoint Test A . For diesel engines Go to Pinpoint Test F .
P0977^b	SSPCB O/D Clutch	SSPCB or circuit shorted to power	Voltage through SSPCB circuit is checked. An error will be noted if calibration is exceeded. Short to power failure detected.	Tow/Haul OFF: Only 1st and 3rd gears available. Tow/Haul ON: Only 5th gear available.	For gasoline engines Go to Pinpoint Test A . For diesel engines Go to Pinpoint Test F .
P0760^a	Shift Solenoid Pressure Control C (SSPCC) Intermediate Clutch	SSPCC circuit open	SSPCC circuit failed to provide voltage drop across solenoid. Circuit open or PCM drive failure during OBD test.	Tow/Haul OFF: Only 1st and 2nd gears available. Tow/Haul ON: Only 5th gear available.	For gasoline engines Go to Pinpoint Test A . For diesel engines Go to Pinpoint Test F .
P0761	SSPCC Intermediate Clutch	SSPCC clutch or solenoid failure - OFF	SSPCC clutch or solenoid failed in the OFF position during operation resulting in LOW pressure in the hydraulic circuit.	No 3rd and 4th gear available.	REFER to Diagnosis By Symptom .
P0762	SSPCC Intermediate Clutch	SSPCC clutch or solenoid failure - ON	SSPCC clutch or solenoid failed in the ON position during operation resulting in HIGH pressure in the hydraulic circuit.	Only 3rd and 4th gear available.	REFER to Diagnosis By Symptom .
P0763^a	SSPCC Intermediate Clutch	SSPCC solenoid circuit failure	SSPCC circuit failed to provide voltage drop across solenoid. Circuit failure or PCM driver failure.	Tow/Haul OFF: Only 1st, 2nd and 3rd gears available. Tow/Haul ON: Only 4th and 5th gear available.	For gasoline engines Go to Pinpoint Test A . For diesel engines Go to Pinpoint Test F .
P0979	SSPCC Intermediate Clutch	SSPCC solenoid or circuit shorted to ground	Voltage through SSPCC circuit is checked. An error will be noted if calibration is exceeded. Short to ground failure detected.	Tow/Haul OFF: Only 3rd gear available. Tow/Haul ON: Only 4th gear available.	For gasoline engines Go to Pinpoint Test A . For diesel engines Go to Pinpoint Test F .
P0980^b	SSPCC Intermediate Clutch	SSPCC solenoid or circuit shorted to power	Voltage through SSPCC circuit is checked. An error will be noted if calibration is exceeded. Short to power failure detected.	Tow/Haul OFF: Only 1st and 2nd gear available. Tow/Haul ON: Only 5th gear available.	For gasoline engines Go to Pinpoint Test A . For diesel engines Go to Pinpoint Test F .
P0765	Shift Solenoid Pressure Control D (SSPCD) Direct Clutch	SSPCD circuit open	SSPCD circuit failed to provide voltage drop across solenoid. Circuit open or PCM driver failure during OBD test.	Tow/Haul OFF: Only 5th gear available. Tow/Haul ON: Only 6th gear available.	For gasoline engines Go to Pinpoint Test A . For diesel engines Go to Pinpoint Test F .
P0766	SSPCD Direct Clutch	SSPCD clutch or solenoid failure - OFF	SSPCD clutch or solenoid failed in the OFF position during operation resulting in HIGH pressure in the hydraulic circuit.	Tow/Haul OFF: No 5th gear available. Tow/Haul ON: No 5th or 6th gears available.	REFER to Diagnosis By Symptom .
P0767	SSPCD Direct Clutch	SSPCD clutch or solenoid failure - ON	SSPCD clutch or solenoid failed in the ON position during operation resulting in LOW pressure in the hydraulic circuit.	No 1st, 2nd, 3rd or 4th gears available.	REFER to Diagnosis By Symptom .
P0768	SSPCD Direct Clutch	SSPCD circuit failure	SSPCD circuit failed to provide voltage drop across solenoid. Circuit failure or PCM driver failure.	Tow/Haul OFF: Only 1st, 2nd, and 5th gears available. Tow/Haul ON: Only 5th and 6th gear available.	For gasoline engines Go to Pinpoint Test A . For diesel engines Go to Pinpoint Test F .
P0982^b	SSPCD Direct Clutch	SSPCD solenoid or circuit shorted to ground	Voltage through SSPCD solenoid circuit is checked. An error will be noted if calibration is exceeded. Short to ground failure detected.	Tow/Haul OFF: Only 1st and 2nd gears available. Tow/Haul ON: Only 5th gear available.	For gasoline engines Go to Pinpoint Test A . For diesel engines Go to Pinpoint Test F .
P0983^b	SSPCD Direct Clutch	SSPCD solenoid or circuit shorted to power	Voltage through SSPCD circuit is checked. An error will be noted if calibration is exceeded. Short to power failure detected.	Tow/Haul OFF: Only 5th gear available. Tow/Haul ON: Only 6th gear available.	For gasoline engines Go to Pinpoint Test A . For diesel engines Go to Pinpoint Test F .
P0770	Shift Solenoid Pressure Control E (SSPCE) Low/ Reverse Clutch	SSPCE circuit open	SSPCE circuit failed to provide voltage drop across solenoid. Circuit open or PCM drive failure during OBD test.	Tow/Haul OFF: Only 1st and 2nd gears available. Tow/Haul ON: Only 5th gear available.	For gasoline engines Go to Pinpoint Test A . For diesel engines Go to Pinpoint Test F .
P0771	SSPCE Low/ Reverse Clutch	SSPCE circuit, clutch or solenoid failure - OFF	SSPCE circuit, clutch or solenoid failed in the ON position during operation resulting in LOW pressure in the hydraulic circuit.	Tow/Haul OFF: No 1st gear available. Tow/Haul ON: No 1st or 2nd gears available.	REFER to Diagnosis By Symptom .
P0772	SSPCE Low/ Reverse Clutch	SSPCE clutch or solenoid failure - ON	SSPCE clutch or solenoid failed in the ON position during operation resulting in HIGH pressure in the hydraulic circuit.	Tow/Haul OFF: Only 1st gear available. Tow/Haul ON: Only 1st or 2nd gears available.	REFER to Diagnosis By Symptom .
P0773	SSPCE Low/ Reverse Clutch	SSPCE circuit failure	SSPCE circuit failed to provide voltage drop across solenoid. Circuit failure or PCM driver failure.	Tow/Haul OFF: Only 1st and 2nd gears available. Tow/Haul ON: Only 5th gear available.	For gasoline engines Go to Pinpoint Test A . For diesel engines Go to Pinpoint Test F .
P0985^b	SSPCE Low/ Reverse Clutch	SSPCE solenoid or circuit shorted to ground	Voltage through SSPCE circuit is checked. An error will be noted if calibration is exceeded. Short to ground failure detected.	Tow/Haul ON: Only 5th gear available.	For gasoline engines Go to Pinpoint Test A . For diesel engines Go to Pinpoint Test F .
P0986^b	SSPCE Low/ Reverse Clutch	SSPCE solenoid or circuit shorted to power	Voltage through SSPCE circuit is checked. An error will be noted if calibration is exceeded. Short to power failure detected.	Tow/Haul OFF: Only 1st and 2nd gears available. Tow/Haul ON: Only 5th gear available.	For gasoline engines Go to Pinpoint Test A . For diesel engines Go to Pinpoint Test F .
P0791	Intermediate Shaft Speed Sensor	Insufficient input from intermediate shaft speed sensor	PCM detected an insufficient signal from the intermediate shaft speed sensor during operation.	Harsh shifts or engagements, engine RPM higher or lower than expected. No 1st, 3rd or 5th gears.	For gasoline engines Go to Pinpoint Test D . For diesel engines Go to Pinpoint Test I .
P0793	Intermediate Shaft Speed Sensor	No input from intermediate shaft speed sensor	PCM detected a loss of intermediate shaft speed sensor signal during operation.	Harsh shifts or engagements, engine RPM higher or lower than expected. No 1st, 3rd or 5th gears.	For gasoline engines Go to Pinpoint Test D . For diesel engines Go to Pinpoint Test I .
P0794	Intermediate Shaft Speed Sensor	Intermediate shaft speed sensor signal intermittent	PCM has detected an intermittent intermediate shaft speed sensor signal.	-	For gasoline engines Go to Pinpoint Test D . For diesel engines Go to Pinpoint Test I .
P0657	Transmission Solenoid Power Control	Transmission solenoid power control high side power supply circuit failed	Transmission Solenoid Power Control high side power supply circuit failed.	Only REVERSE, NEUTRAL and 5th gear available. Engine RPM at idle is about 1,000 RPM when transmission solenoid power control is off as a Failure Mode and Effects Management action.	Power to all solenoids has been interrupted. CHECK for opens, short to ground and harness disconnection. REPAIR as required. When transmission solenoid power control is commanded OFF as a Failure Mode and Effects Management action, CHECK all solenoids for correct function as listed in the band, clutch, solenoid and switch application chart. For gasoline engines Go to Pinpoint Test A . For diesel engines Go to Pinpoint Test F .
P1910	Reverse Lamp Driver Circuit	Reverse lamp driver control circuit failed	Reverse lamp driver control circuit failed.	No reverse lamps in REVERSE. TR sensor is OK.	REFER to EXTERIOR LIGHTING article and/or vehicle wiring diagrams.
P1124	TP Sensor	TP voltage high/low for OBD test	TR was not in the correct position for OBD test.	Rerun at appropriate TP per application.	REFER to the appropriate Engine Performance article^a .
P1460	A/C Switch	A/C pressure cycling switch error	A/C or defrost ON condition may result from A/C clutch being ON during OBD test.	DTC set during OBD: rerun with A/C off. Failed ON: line pressure slightly low with A/C off.	REFER to the appropriate Engine Performance article^a .
P1572	Brake Pedal Position (BPP) Switch	BPP switch circuit failed	Brake ON circuit failure during normal operation.	Failed ON or not connected: TCC will not engage at less than one-third throttle. Failed OFF or not connected: TCC will not disengage when the brake is applied.	REFER to the appropriate Engine Performance article^a .
P1703	BPP Switch	Brake not cycled during OBD KOER or BPP switch circuit failed	Brake not cycling during KOER or brake ON circuit failure during KOEO.	Failed ON or not connected: TCC will not engage at less than one-third throttle. Failed OFF or none connected: TCC will not disengage when the brake is applied.	REFER to the appropriate Engine Performance article^a .
P1780	Transmission Control Switch (TCS)	TCS input incorrect per selected position	TCS voltage incorrect.	No Tow/Haul feature when TCS is pressed during Self Test.	RERUN OBD test and cycle switch. If concern is still present, REFER to AUTOMATIC TRANSAXLE/TRANSMISSION EXTERNAL CONTROLS article.
P1636	Shift Solenoid x (SSx)	SSx communication error	PCM has detected an internal error.	None.	INSTALL a new PCM.
P2700	Coast Clutch	Coast clutch failed ON or OFF	The PCM has detected a failure within the coast clutch system.	Not all gears available. Tow/Haul OFF: No 1st, 2nd, 3rd or 5th gears available. Tow/Haul ON: No 1st, 2nd, 4th or 5th gears available.	Coast clutch failed ON or OFF. SEE PID P0730_Status Chart. REFER to Diagnostic Parameters Identification (PID) Chart . For gasoline engines Go to Pinpoint Test A . For diesel engines Go to Pinpoint Test F . REFER to the Solenoid Application charts located at the beginning of Pinpoint Tests - OSC Equipped Vehicle . If other solenoid DTCs are present, for gasoline engines Go to Pinpoint Test A . For diesel engines Go to Pinpoint Test F . If only P0730 and/or 2700 series DTCs are present, INSTALL the appropriate clutch solenoid. CLEAR the DTCs, road test vehicle. If the concern is still present, REPAIR/INSTALL new internal transmission components.
P2701	O/D Clutch	O/D clutch failed ON or OFF	The PCM has detected a failure within the O/D clutch system.	Not all gears available. Tow/Haul OFF: No 1st, 2nd, 3rd or 5th gears available. Tow/Haul ON: No 2nd, 4th or 6th gears available.	O/D clutch failed ON or OFF. SEE PID P0730_Status Chart. REFER to Diagnostic Parameters Identification (PID) Chart . For gasoline engines Go to Pinpoint Test A . For diesel engines Go to Pinpoint Test F . REFER to the Solenoid Application charts located at the beginning of Pinpoint Tests - OSC Equipped Vehicle . If other solenoid DTCs are present, for gasoline engines Go to Pinpoint Test A . For diesel engines Go to Pinpoint Test F . If only P0730 and/or 2700 series DTCs are present, INSTALL the appropriate clutch solenoid. CLEAR the DTCs, road test vehicle. If the concern is still present, REPAIR/INSTALL new internal transmission components.
P2702	Intermediate Clutch	Intermediate clutch failed ON or OFF	The PCM has detected a failure within the intermediate clutch system.	Not all gears available. No 3rd and 4th gears available. Only 3rd and 4th gears available.	Intermediate clutch failed ON or OFF. SEE PID P0730_Status Chart. REFER to Diagnostic Parameters Identification (PID) Chart . For gasoline engines Go to Pinpoint Test A . For diesel engines Go to Pinpoint Test F . REFER to the Solenoid Application charts located at the beginning of Pinpoint Tests - OSC Equipped Vehicle . If other solenoid DTCs are present, for gasoline engines Go to Pinpoint Test A . For diesel engines Go to Pinpoint Test F . If only P0730 and/or 2700 series DTCs are present, INSTALL the appropriate clutch solenoid. CLEAR the DTCs, road test vehicle. If the concern is still present, REPAIR/INSTALL new internal transmission components.
P2703	Direct Clutch	Direct clutch failed ON or OFF	The PCM has detected a failure within the direct clutch system.	Not all gears available. Tow/Haul OFF: No 1st, 2nd, 3rd or 4th gears available. No 5th or 6th gears available.	Direct clutch failed ON or OFF. SEE PID P0730_Status Chart. REFER to Diagnostic Parameters Identification (PID) Chart . For gasoline engines Go to Pinpoint Test A . For diesel engines Go to Pinpoint Test F . REFER to the Solenoid Application charts located at the beginning of Pinpoint Tests - OSC Equipped Vehicle . If other solenoid DTCs are present, for gasoline engines Go to Pinpoint Test A . For diesel engines Go to Pinpoint Test F . If only P0730 and/or 2700 series DTCs are present, INSTALL the appropriate clutch solenoid. CLEAR the DTCs, road test vehicle. If the concern is still present, REPAIR/INSTALL new internal transmission components.
P2704	Low Reverse Clutch	Low reverse clutch failed ON or OFF	The PCM has detected a failure within the low reverse clutch system.	Not all gears available. Tow/Haul OFF: No 1st gear available. Only 1st gear available. Tow/Haul ON: No 1st or 2nd gears available. Only 1st or 2nd gears available.	Low reverse clutch failed ON or OFF. SEE PID P0730_Status Chart. REFER to Diagnostic Parameters Identification (PID) Chart . For gasoline engines Go to Pinpoint Test A . For diesel engines Go to Pinpoint Test F . REFER to the Solenoid Application charts located at the beginning of Pinpoint Tests - OSC Equipped Vehicle . If other solenoid DTCs are present, for gasoline engines Go to Pinpoint Test A . For diesel engines Go to Pinpoint Test F . If only P0730 and/or 2700 series DTCs are present, INSTALL the appropriate clutch solenoid. CLEAR the DTCs, road test vehicle. If the concern is still present, REPAIR/INSTALL new internal transmission components.

^a Output circuit check, generated only by electrical symptoms.

^b May also generate by some other non-electrical transmission hardware system.