LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2000 >> Contour SE, 2.5 L, Standard >> Repair and Diagnosis >> External Pages >> Different car >> Section 1991 (Engine - 2.3L - (Hybrid)) >> In-Vehicle Servicing >> Engine Front Cover >> Installation

Engine Front Cover: Installation

WARNING: This page is about a different car, the 2007 Mercury Mariner and 2007 Ford Escape. However, it is still accessible from the selected car via links, so may be relevant.
    CAUTION: Do not use metal scrapers, wire brushes, power abrasive disks or other abrasive means to clean sealing surfaces. These tools cause scratches and gouges which make leak paths.
  1. Clean and inspect the mounting surfaces of the engine and the front cover.
    2. NOTE: The engine front cover must be installed and the bolts tightened within 4 minutes of applying the silicone gasket and sealant.
  2. Apply a 2.5 mm (0.09 in) bead of silicone gasket and sealant to the cylinder head and oil pan joint areas. Apply a 2.5 mm (0.09 in) bead of silicone gasket and sealant to the front cover.
    3. Fig 1: Locating Silicone Gasket
    G03897744Courtesy of FORD MOTOR CO.
  3. Install the engine front cover. Tighten the bolts in the sequence shown, to the following specifications:
    • Tighten the 8-mm bolts to 10 Nm (89 lb-in).
    • Tighten the 13-mm bolts to 48 Nm (35 lb-ft).
    4. Fig 2: Identifying Engine Front Cover Bolts Tightening Sequence
    GF0024077Courtesy of FORD MOTOR CO.
    NOTE: Remove the through-bolt from the special tool.
    NOTE: Lubricate the oil seal with clean engine oil.
  4. Using the special tool, install the crankshaft front oil seal.
    5. Fig 3: Installing Crankshaft Front Oil Seal Using Special Tool
    G03897717Courtesy of FORD MOTOR CO.
  5. Install the accessory drive belt tensioner and the 3 bolts.
    • Tighten to 25 Nm (18 lb-ft).
  6. Install the coolant pump pulley and the 3 bolts.
    • Tighten to 20 Nm (15 lb-ft).
  7. Install the engine mount. For additional information, refer to Engine Mount .
  8. Install the crankshaft pulley. For additional information, refer to Crankshaft Pulley .
    9. CAUTION: Only hand-tighten the bolt or damage to the front cover can occur.
  9. Install a standard 6 mm (0.23 in) x 18 mm (0.7 in) bolt through the crankshaft pulley and thread it into the front cover.
    10. Fig 4: Aligning Crankshaft Pulley Bolt Holes
    G03897704Courtesy of FORD MOTOR CO.
    NOTE: Whenever the CKP sensor is removed, a new one must be installed using the alignment tool supplied with the new part.
  10. Install a new CKP sensor and the 2 bolts.
    • Do not tighten the bolts at this time.
    11. Fig 5: Locating CKP Sensor Bolts
    GF0024078Courtesy of FORD MOTOR CO.
    NOTE: The CKP sensor alignment tool is supplied with the new sensor and is not available separately.
  11. Adjust the CKP sensor with the alignment tool.
    • Tighten the 2 CKP bolts to 7 Nm (62 lb-in).
    12. Fig 6: Locating CKP Sensor Alignment Tool And Bolts
    GF0009614Courtesy of FORD MOTOR CO.
  12. Connect the CKP sensor electrical connector.
  13. Remove the 6 mm (0.23 in) x 18 mm (0.7 in) bolt.
    14. Fig 7: CKP Sensor Electrical Connector
    GF0024369Courtesy of FORD MOTOR CO.
  14. Install the accessory drive belt. For additional information, refer to ACCESSORY DRIVE - HYBRID article.
scientia non olet · About LEMON Manuals