LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2000 >> Contour SE, 2.5 L, Standard >> Repair and Diagnosis >> External Pages >> Different car >> Section 1917 (Steering Column - F250-F550) >> Disassembly And Assembly >> Steering Column - Automatic Transmission >> Disassembly >> All vehicles

All vehicles

WARNING: This page is about a different car, the 2007 Ford Pickup, 2007 Ford F550 Super Duty, 2007 Ford F450 Super Duty, and 2007 Ford Cab & Chassis. However, it is still accessible from the selected car via links, so may be relevant.
  1. Remove the steering column. For additional information, refer to Steering Column  in this article.
  2. Remove the clockspring. For additional information, refer to SUPPLEMENTAL RESTRAINT SYSTEM article.
    3. CAUTION: Carefully note the position of the steering column lock gear, bearing and retainer prior to removal.
    Fig 1: Locating Snap Ring
    GF0007835Courtesy of FORD MOTOR CO.
  3. Remove the snap ring.
  4. Remove the steering column lock housing bearing.
    Fig 2: Locating Steering Column Lock Housing Bearing
    GF0007836Courtesy of FORD MOTOR CO.
  5. Remove the steering column lock gear.
    Fig 3: Locating Steering Column Lock Gear
    GF0007837Courtesy of FORD MOTOR CO.
  6. Remove the gearshift lever pin and the gearshift lever.


  1. Remove the steering column bearing tolerance ring from the steering column shaft.
    Fig 1: Locating Steering Column Bearing Tolerance Ring
    GF0007839Courtesy of FORD MOTOR CO.
  2. Remove the 2 lock cylinder housing pivot screws.
    Fig 2: Locating Lock Cylinder Housing Pivot Screws
    GF0007813Courtesy of FORD MOTOR CO.
    3. WARNING: The steering column position spring is under tension and can come out with great force. Failure to follow these instructions may result in personal injury.
    Fig 3: Identifying Shop Fabricated Tool And Steering Column Position Spring
    G04309597Courtesy of FORD MOTOR CO.
  3. Remove the steering column lock cylinder housing and the steering column shaft from the steering actuator housing.
    • Pry up on the steering column locking levers using a shop fabricated tool.
    • On tilt steering columns, remove the steering column position spring.
  4. Using a flat-blade screwdriver, pry up on the flush surface of the turn indicator cancel cam and remove.
    Fig 4: Prying Up On Flush Surface Of Turn Indicator Cancel Cam Using Flat-Blade Screwdriver
    GF0007840Courtesy of FORD MOTOR CO.
  5. Remove the snap ring.
    Fig 5: Locating Snap Ring
    G03884923Courtesy of FORD MOTOR CO.
  6. Remove the steering column upper bearing spring.
    Fig 6: Locating Steering Column Bearing Spring
    G03884924Courtesy of FORD MOTOR CO.
  7. Remove the steering column bearing sleeve.
    Fig 7: Locating Steering Column Bearing Sleeve
    G04708925Courtesy of FORD MOTOR CO.
  8. Remove the steering column bearing tolerance ring.
    • Slide the steering column shaft in toward the steering column lock cylinder housing.
    • Slide the steering column bearing tolerance ring from the steering column shaft and remove the shaft.
    Fig 8: Identifying Steering Column Bearing Tolerance Ring
    GF0007815Courtesy of FORD MOTOR CO.
  9. Using a punch, remove the steering column upper bearing from the steering column lock cylinder housing.
    Fig 9: Removing Steering Column Bearing Using Suitable Punch
    GF0007816Courtesy of FORD MOTOR CO.


    CAUTION: If installing a new transmission shift selector position insert, make sure that the correct part is being installed.
    Fig 1: Identifying Brake Shift Interlock Solenoid Transmission Shift Position Insert
    GF0007841Courtesy of FORD MOTOR CO.
  1. Remove the brake shift interlock solenoid and the transmission shift position insert.
    • Remove the 3 bolts.
    • Remove the brake shift interlock solenoid and the transmission shift position insert.
  2. Remove the shift tube.
    • Remove the 4 bolts.
    • Remove the 2 shift tube clamps.
    • Remove the shift tube.
    Fig 2: Identifying Shift Tube
    GF0007842Courtesy of FORD MOTOR CO.
  3. Remove the transmission shift arm assembly.
    • Remove the 2 bolts.
    • Remove the transmission shift arm assembly.
    Fig 3: Removing Transaxle Shift Arm Assembly
    GF0007843Courtesy of FORD MOTOR CO.
  4. Remove the spring.
    Fig 4: Locating Gearshift Selector Tube Spring
    G03884933Courtesy of FORD MOTOR CO.
  5. Drive out the gearshift lever pin from the shift tube.
    Fig 5: Locating Gearshift Lever Pin
    GF0007844Courtesy of FORD MOTOR CO.
  6. Remove the gearshift lever.
    Fig 6: Locating Gearshift Lever
    G03884935Courtesy of FORD MOTOR CO.
  7. Remove the column shift selector lever plunger.
    • If it is bent, replace the column shift selector lever plunger.
    Fig 7: Locating Column Shift Selector Lever Plunger
    GF0007845Courtesy of FORD MOTOR CO.
  8. Remove the 2 gearshift lever socket bushings and the transmission control selector lever spring clip.
    Fig 8: Locating Gearshift Lever Socket Bushings And Transmission Control Selector Lever Spring Clip
    GF0007846Courtesy of FORD MOTOR CO.
  9. Remove the steering column lock pawl.
    • Drive out the steering column lock lever pin.
    • Remove the steering column lock pawl.
    Fig 9: Removing Steering Column Lock Pawl
    GF0007847Courtesy of FORD MOTOR CO.
  10. Remove the ignition switch.
    • Remove the 2 screws.
    • Remove the ignition switch.
    Fig 10: Removing Ignition Switch
    GF0007806Courtesy of FORD MOTOR CO.
  11. Remove the steering column lower bearing and sleeve.
    Fig 11: Locating Steering Column Lower Bearing And Sleeve
    GF0007848Courtesy of FORD MOTOR CO.
  12. Remove the steering column lower bearing retainer.
    • Remove the bolts.
    • Remove the steering column lower bearing retainer.
    Fig 12: Identifying Steering Column Lower Bearing Retainer
    GF0007849Courtesy of FORD MOTOR CO.
  13. Remove the steering column upper and lower lock actuators.
    Fig 13: Removing Steering Column Upper And Lower Lock Actuators
    GF0007850Courtesy of FORD MOTOR CO.
scientia non olet · About LEMON Manuals