LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2000 >> Contour SE, 2.5 L, Standard >> Repair and Diagnosis >> External Pages >> Different car >> Section 1825 (Windows And Glass - F-150 & Mark LT) >> Diagnostic Tests >> Glass, Frames and Mechanisms >> Pinpoint Tests >> Pinpoint Test E: A Single Power Window is Inoperative - Passenger Rear Window >> Pinpoint Test E: A Single Power Window Is Inoperative - Passenger Rear Window

Pinpoint Test E: A Single Power Window Is Inoperative - Passenger Rear Window

WARNING: This page is about a different car, the 2007 Lincoln Mark LT and 2007 Ford Pickup. However, it is still accessible from the selected car via links, so may be relevant.
  1. E1 CHECK THE VOLTAGE TO THE PASSENGER REAR WINDOW CONTROL SWITCH - CIRCUIT 193 (YE/LG) 
    • Disconnect: Passenger Rear Window Control C801
    • Key in ON position.
      • NOTE: Set the driver window control switch to the UNLOCK position.
      Fig 1: Checking Voltage To Passenger Rear Window Control Switch - Circuit 193 (YE/LG)
      GF0001968Courtesy of FORD MOTOR CO.
    • Measure the voltage between passenger rear window control switch C801-4, circuit 193 (YE/LG) harness side and ground.
    • Is the voltage greater than 10 volts? 
    1. YES  : Go to  E2.
    2. NO  : REPAIR the circuit. TEST system for normal operation.
  2. E2 CHECK THE GROUNDS TO THE PASSENGER REAR WINDOW CONTROL SWITCH - CIRCUITS 320 (RD/BK) AND 319 (YE/BK) 
    • Key in OFF position.
    • Measure the resistance between passenger rear window control switch C801-3, circuit 320 (RD/BK) and ground, and between C801-5, circuit 319 (YE/BK) harness side and ground.
      Fig 2: Checking Grounds To Passenger Rear Window Control Switch - Circuits 320 (RD/BK) And 319 (YE/BK)
      GF0001969Courtesy of FORD MOTOR CO.
    • Is the resistance less than 5 ohms? 
    1. YES  : Go to  E4.
    2. NO  : Go to  E3.
  3. E3 CHECK CIRCUITS 320 (RD/BK) AND 319 (YE/BK) FOR AN OPEN 
    • Key in OFF position.
    • Disconnect: Driver Window Control Switch C504a
    • Measure the resistance between driver window control switch C504a-3, circuit 320 (RD/BK) and passenger rear window control switch C801-3, circuit 320 (RD/BK), harness side.
      Fig 3: Checking Circuits 320 (RD/BK) And 319 (YE/BK) For Open (1 Of 2)
      GF0001970Courtesy of FORD MOTOR CO.
    • Measure the resistance between driver window control switch C504a-4, circuit 319 (YE/BK) and passenger rear window control switch C801-5, circuit 319 (YE/BK), harness side.
      Fig 4: Checking Circuits 320 (RD/BK) And 319 (YE/BK) For Open (2 Of 2)
      GF0001971Courtesy of FORD MOTOR CO.
    • Are the resistances less than 5 ohms? 
    1. YES  : INSTALL a new passenger rear window control switch. REFER to Window Control Switch - Rear  in this article. TEST the system for normal operation.
    2. NO  : REPAIR circuit 320 (RD/BK) or circuit 319 (YE/BK). TEST the system for normal operation.
  4. E4 CHECK THE PASSENGER REAR WINDOW CONTROL SWITCH 
    • Disconnect: Passenger Rear Window Control Switch C801
    • Key in ON position.
      NOTE: Set the driver window control switch to the UNLOCK position.
    • Connect a fused jumper wire between passenger rear window control switch C801-5, circuit 319 (YE/BK) and C801-2, circuit 882 (BN/YE); and a second fused jumper wire between C801-4, circuit 193 (YE/LG) and C801-6, circuit 881 (BN) harness side. The window should operate in the upward direction.
      Fig 5: Checking Passenger Rear Wiudow Control Switch (1 Of 2)
      GF0001972Courtesy of FORD MOTOR CO.
    • Connect a fused jumper wire between passenger rear window control switch C801-3, circuit 320 (RD/BK) and C801-6, circuit 881 (BN); and a second fused jumper wire between C801-4, circuit 193 (YE/LG) and C801-2, circuit 882 (BN/YE) harness side. The window should operate in the downward direction.
      Fig 6: Checking Passenger Rear Window Control Switch (2 Of 2)
      GF0001973Courtesy of FORD MOTOR CO.
    • Does the window operate correctly? 
    1. YES  : If the passenger rear window did not operate with the passenger rear window control switch, INSTALL a new passenger rear window control switch. REFER to Window Control Switch - Rear  in this section. If the passenger rear power window did operate with the passenger rear window control switch but not with the driver front window control switch, INSTALL a new passenger front window control switch. REFER to Window Control Switch - Front  in this article. TEST the system for normal operation.
    2. NO  : Go to  E5.
  5. E5 CHECK CIRCUITS 882 (BN/YE) AND 881 (BN) FOR AN OPEN 
    • Key in OFF position.
    • Disconnect: Passenger Rear Window Motor C803
    • Measure the resistance between passenger rear window control switch C801-6, circuit 881 (BN) and passenger rear window motor C803-1, circuit 881 (BN) harness side.
      Fig 7: Checking Circuits 882 (BN/YE) And 881 (BN) For Open (1 Of 2)
      GF0001974Courtesy of FORD MOTOR CO.
    • Measure the resistance between passenger rear window control switch C801-2, circuit 882 (BN/YE) and passenger rear window motor C803-2, circuit 882 (BN/YE) harness side.
      Fig 8: Checking Circuits 882 (BN/YE) And 881 (BN) For Open (2 Of 2)
      GF0001975Courtesy of FORD MOTOR CO.
    • Are the resistances less than 5 ohms? 
    1. YES  : INSTALL a new passenger rear window motor. REFER to Window Regulator and Motor - Rear Door, SuperCab  or Window Regulator and Motor - Rear Door, SuperCrew  in this article. TEST the system for normal operation.
    2. NO  : REPAIR circuit 881 (BN) or circuit 882 (BN/YE). TEST the system for normal operation.
scientia non olet · About LEMON Manuals