LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2000 >> Contour SE, 2.5 L, Standard >> Repair and Diagnosis >> External Pages >> Different car >> Section 1800 (Rear Drive Axle/Differential - Ford 9.75-Inch Ring Gear -- F150 & Mark LT) >> In-Vehicle Servicing >> Differential Bearings >> Removal

Differential Bearings: Removal

WARNING: This page is about a different car, the 2007 Lincoln Mark LT and 2007 Ford Pickup. However, it is still accessible from the selected car via links, so may be relevant.
  1. Remove differential carrier. For additional information, refer to Differential Carrier  in this article.
  2. Remove the 2 differential bearings with the special tools.
    3. Fig 1: Removing Differential Bearing Using Special Tools
    G04583104Courtesy of FORD MOTOR CO.
  3. Index-mark the driveshaft flange and pinion flange for correct alignment during installation.
    4. Fig 2: Identifying Alignment Mark On Driveshaft Flange And Pinion Flange
    GF0003125Courtesy of FORD MOTOR CO.
  4. Remove the 4 driveshaft flange bolts.
    5. Fig 3: Identifying Driveshaft Flange Bolts
    GF0000834Courtesy of FORD MOTOR CO.
    NOTE: The driveshaft centering socket yoke fits tightly on the pinion flange pilot. Never hammer on the driveshaft or any of its components to disconnect the driveshaft centering socket yoke from the pinion flange. Pry only in the area shown with a suitable tool to disconnect the driveshaft centering socket yoke from the pinion flange.
  5. Using a suitable tool as shown, disconnect the driveshaft centering socket yoke from the pinion flange.
    • Using mechanic's wire, position the driveshaft aside.
    6. Fig 4: Disconnecting Driveshaft Flange Yoke From Pinion Flange
    G03878446Courtesy of FORD MOTOR CO.
  6. Using the special tool to hold the pinion flange, remove and discard the pinion nut.
    7. Fig 5: Holding Pinion Flange With Special Tool
    G03883491Courtesy of FORD MOTOR CO.
  7. Using the special tool, remove the pinion flange.
    8. Fig 6: Removing Pinion Flange Using Special Tool
    G03878593Courtesy of FORD MOTOR CO.
  8. Force up on the metal flange of the drive pinion seal. Install gripping pliers and strike with a hammer until the drive pinion seal is removed.
    9. Fig 7: Removing Drive Pinion Oil Seal
    G03878521Courtesy of FORD MOTOR CO.
  9. Remove the drive pinion shaft oil slinger.
    10. Fig 8: Identifying Drive Pinion Shaft Oil Slinger
    GF0003138Courtesy of FORD MOTOR CO.
  10. Install the special tool, then use a soft-faced hammer to drive the pinion gear out of the outer drive pinion bearing and remove the pinion gear.
    11. Fig 9: Identifying Special Tool To Remove Drive Pinion Gear
    G03884424Courtesy of FORD MOTOR CO.
  11. Remove the drive pinion collapsible spacer and discard it.
    12. Fig 10: Identifying Drive Pinion Collapsible Spacer
    GF0000836Courtesy of FORD MOTOR CO.
  12. Using the special tool and a suitable press, remove the inner pinion bearing.
    13. Fig 11: Inner Pinion Bearing And Special Tool
    G03878658Courtesy of FORD MOTOR CO.
  13. Using a brass drift, remove the 2 drive pinion bearing cups by tapping alternately on opposite sides of the 2 drive pinion bearing cups.
    14. Fig 12: Identifying Pinion Bearing Cups
    GF0000837Courtesy of FORD MOTOR CO.
scientia non olet · About LEMON Manuals