LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2000 >> Contour SE, 2.5 L, Standard >> Repair and Diagnosis >> External Pages >> Different car >> Section 1680 (Seat System) >> Removal And Installation >> Seat Backrest - Front >> Removal and Installation

Removal and Installation

WARNING: This page is about a different car, the 2006 Mercury Montego, 2006 Ford Freestyle, and 2006 Ford Five Hundred. However, it is still accessible from the selected car via links, so may be relevant.
WARNING:
  1. Always wear safety glasses when repairing an air bag supplemental restraint system (SRS) vehicle and when handling an airbag module. This will reduce the risk of injury in the event of an accidental deployment.
  2. To reduce the risk of personal injury, do not use any memory saver devices.
  3. After deployment, the air bag surface can contain deposits of sodium hydroxide, a product of the gas generant combustion that is irritating to the skin. Wash your hands with soap and water afterwards.
  4. Never probe the connectors on the air bag module. Doing so can result in air bag deployment, which can result in personal injury.
CAUTION: It is necessary to rezero the occupant classification sensor (OCS) system when a front passenger seat cushion is disassembled, a new trim cover is installed, or an OCS service kit is installed. A diagnostic tool is used to trigger the active command to carry out rezeroing of the OCS system.
NOTE:
  1. If a seat equipped with a supplemental restraint system (SRS) component is being serviced, the supplemental restraint system (SRS) must be depowered.
  2. The air bag warning lamp illuminates when the RCM fuse is removed and the ignition switch is ON. This is normal operation and does not indicate a supplemental restraint system (SRS) fault.
  3. The SRS must be fully operational and free of faults before releasing the vehicle to the customer.

    All seats 

  1. Position the seat to access all the seat track-to-floor pan bolts and the safety belt anchor.
  2. Depower the SRS. For additional information, refer to DEPOWERING PROCEDURE .
  3. Remove the front seat. For additional information, REFER to SEAT - FRONT .

    4. Driver power seat 

  4. Remove the power seat track. For additional information, REFER to SEAT TRACK - FRONT .

    5. Seats with manual recline 

  5. Pull out and remove the manual backrest adjust handle.

    6. Passenger power seat 

  6. Remove the seat control switch knob.

    7. Seats with manual track, 2 and 4-way power seats 

  7. Remove the rear screw, pull out on the side and front and separate the side shield.
    • Vehicles with manual seats, remove the side shield.

    8. 2 and 4-way power seats 

  8. Remove the seat control switch, disconnect it and remove the side shield.

    9. Heated seats or seats with side air bags 

  9. Release the cushion trim cover J-clip at the back of the trim cover.
  10. Release the hook and loop strip at the rear of the cushion trim cover.

    11. Heated seats 

  11. Disconnect the backrest heated seat element electrical connector.

    12. Seats with seat side air bags 

  12. Disconnect and separate the side air bag module electrical connector and wire harness from the cushion pan.

    13. All seats 

  13. Drive out the 2 small roll pins holding the backrest adjuster to the latch/backrest.
  14. Remove the 2 cushion pan-to-lower latch/backrest frame bolts and remove the backrest frame.
  15. To install, reverse the removal procedure.
  16. Install the seat. For additional information, REFER to SEAT - FRONT .
  17. Repower the SRS. Do not prove out the SRS at this time.  For additional information, refer to REPOWERING PROCEDURE .

    18. Passenger seat 

    WARNING: Do not separate components.
    CAUTION: It is necessary to rezero the OCS system when a front passenger seat cushion is disassembled, a new trim cover is installed or an OCS service kit is installed. A diagnostic tool is used to trigger the active command to carry out rezeroing of the OCS system.
    CAUTION: Make sure the seat is completely assembled before rezeroing.
    CAUTION: The following precautions must be taken before rezeroing the OCS system.
    • Make sure the OCS system components are connected and no faults are present.
    • Make sure the OCS system is not at a temperature below 0°C (32°F) or above 45°C (113°F) when initiating the rezeroing process. If the vehicle has been exposed to extreme cold or hot temperatures, the vehicle must be exposed and kept at a temperature within the limits, 0°C to 45°C (32°F to 113°F) for a minimum of 30 minutes.
    • Make sure nothing is present on the passenger seat before rezeroing and nothing is placed on the seat during the rezeroing process.
    • Make sure a minimum 8-second time period has passed after cycling the ignition switch ON before the rezeroing process.
    NOTE:
    1. For best results in rezeroing, the OCS system should be at or near room temperature, 10°C to 29°C (50°F to 85°F).
    2. If the first attempt to rezero the OCS system is unsuccessful, a second attempt must be made.
  18. Rezero the occupant classification sensor.
    • With the front passenger seat empty, use a diagnostic tool to trigger the active command and rezero the OCS.
    19. NOTE: The ignition switch must be cycled after rezeroing the OCS system.
  19. Cycle the ignition switch from ON to OFF.

    20. All seats 

  20. Prove out the supplemental restraint system (SRS) as follows:

Turn the ignition key from ON to OFF. Wait 10 seconds, then turn the key back to ON and visually monitor the air bag indicator with the air bag modules installed. The air bag indicator will light continuously for approximately 6 seconds and then turn off. If an air bag supplemental restraint system (SRS) fault is present, the air bag indicator will:

The flashing might not occur until approximately 30 seconds after the ignition switch has been turned from the OFF to the ON position. This is the time required for the restraints control module (RCM) to complete the testing of the SRS. If the air bag indicator is inoperative and a SRS fault exists, a chime will sound in a pattern of 5 sets of 5 beeps. If this occurs, the air bag indicator and any SRS fault discovered must be diagnosed and repaired.

Clear all continuous DTCs from the restraints control module using a diagnostic tool.

scientia non olet · About LEMON Manuals