LEMON Manuals: Even more car manuals for everyone
Home >> Ford >> 2000 >> Contour SE, 2.5 L, Standard >> Repair and Diagnosis >> External Pages >> Different car >> Section 1561 (HVAC Control System - F250-F550 Super Duty) >> Removal And Installation >> Clutch and Clutch Field Coil >> Installation

Clutch and Clutch Field Coil: Installation

WARNING: This page is about a different car, the 2006 Ford Pickup, 2006 Ford F550 Super Duty, 2006 Ford F450 Super Duty, and 2006 Ford Cab & Chassis. However, it is still accessible from the selected car via links, so may be relevant.
    NOTE: If installing a new A/C compressor, the A/C clutch components should be reused unless obvious signs of damage are found. If excessive grooving is found, a new A/C clutch disc and hub and A/C compressor pulley must be installed together. Otherwise, each component can be installed individually where needed.
  1. Visually inspect the A/C clutch disc and hub, A/C compressor pulley and A/C clutch field coil for damage.
    • Inspect for physical damage, including cracked or melted components or discoloration due to excessive heat.
    • Inspect for excessive wear, including grooving in the A/C clutch disc and hub or A/C compressor pulley that is more than fingernail depth.
    • Inspect for roughness in the A/C compressor pulley bearing.
  2. Clean the A/C clutch field coil and the pulley bearing mounting surfaces.
    3. CAUTION: Do not use air tools. The A/C clutch field coil can be easily damaged.
  3. Install the A/C clutch field coil.
    1. Place the A/C clutch field coil on the A/C compressor with the A/C clutch field coil electrical connector correctly positioned.
    2. Place the special tool on the A/C clutch field coil.
    3. Place the special tool on the special tool.
    4. Use the special tool to install the A/C clutch field coil until bottomed completely against the A/C compressor.
      Fig 1: Identifying A/C Clutch Field Coil Until Bottomed Completely Against A/C Compressor
      G04645162Courtesy of FORD MOTOR CO.
    4. NOTE: The A/C clutch pulley is a tight fit on the A/C compressor head; it must be correctly aligned during installation.
    Fig 2: Identifying A/C Clutch Pulley
    G04645163Courtesy of FORD MOTOR CO.
  4. Install the A/C clutch pulley.
  5. Install the pulley snap ring with the bevel side out.
    Fig 3: Locating Pulley Snap Ring With Bevel Side Out
    G04645164Courtesy of FORD MOTOR CO.
  6. Place one nominal thickness A/C clutch disc and hub spacer inside the clutch hub spline opening.
    Fig 4: Locating Nominal Thickness A/C Clutch Disc And Hub Spacer Inside Clutch Hub Spline Opening
    G04645165Courtesy of FORD MOTOR CO.
  7. Install the A/C clutch disc and hub.
    Fig 5: Locating A/C Clutch Disc & Hub
    G03902426Courtesy of FORD MOTOR CO.
  8. Install the A/C clutch disc and hub retaining bolt.
    1. Hold the A/C clutch disc and hub with the special tool.
    2. Tighten the bolt to 13 Nm (10 lb-ft).
      Fig 6: Using Special Tool To Hold A/C Disc And Hub Assembly
      G03952015Courtesy of FORD MOTOR CO.
  9. Measure and adjust the clutch air gap by removing or adding the A/C clutch disc and hub spacer.
    Fig 7: Checking A/C Compressor Clutch Air Gap
    G03879165Courtesy of FORD MOTOR CO.
  10. Install the A/C compressor. For additional information, refer to AIR CONDITIONING (A/C) COMPRESSOR .
scientia non olet · About LEMON Manuals